Conlan 460116 User manual

secure open
Conlan ApS • Speditorvej 2A • DK-9000 Aalborg • Tel: [phone] • Fax: [phone]
www.conlan.eu • [email protected]
Wiegand
Controller
Art. No.: 460116
User manual
Wiegand_usermanual_ENGjun15

2
Two way - One door controller
Specikations:
• Controller for one door, 2 readers
• Space for 511 user codes/tags + 1 Master code/tag
• 3584o-lineeventswithdateandtimestamp
• Real time clock
• Backup battery for clock, EEProm memory
• Dual-processor
• Fully stand alone or networkable
• Possibillityforstandaloneadd/deletecodes/tagsincludinglostordamagedtagswithoutneedtodeleteall
users or connect to a PC
• PCconnectionviaRS485orRS232
• Network connection or direct connection to RS232 serial port
• Lockingdevicerelay,NO/NCselectablebyJumper/software
• Alarmrelay,NO/NCselectablebyJumper/software
• Door contact input (NC)
• Request to exit button (REX) (NC)
• Inputs for two 26 bit Wiegand readers (In and Out)
• Open collector outputs for reader LED and buzzer
• Stand alone reset using wire
• Tamperswitch(NC)
• 12 Vcc, 500 mA max. power input.
Connections
!!! Caution-readalltheinstructionsinordertoassureaproperworkingofthecontroller
12V; GND Power supply, 12 Vcc, 500 mA max.
T;T Tamperswitch(NC)
GND Ground
x-; x+ RS485 port
LK;LK Lockingdevicerelay
AL; AL Alarm relay
BUZ Open collector output for buzzer
LED Open collector output for LED
COM Common door contact and REX
CM Door contact input
REX Request to exit input (REX)
D0; D1 Data from readers
Power supply
12 V / 500 mA
CM REX
W26CTRL COM CM REX D0 D1 D0 D1LEDBUZ
GND12VTTGNDX-X+LKLKALAL
J1 J2
J3
485 232
Entry Exit
Exit
reader
Entry
reader

Note:
1. Incasethatyouareusingjustonereaderlettheotherinputsunconnected
2. Incasethatyouarenotusingdoorcontactinput,shortcircuitwithawirebetweenCOMandCM.Bydefault
door contact input is NC.
Jumper conguration:
J1 - Alarm relay NO or NC J2-LockingdevicerelayNOorNC J3 - Communication port , RS232 or RS485
Programming:
Bydefault,thefollowingparametersareset:
• Mastercodedened(4711)
• Nousercodes/tagsdened
• Door unlock time = 5 seconds
• Door open time = 30 seconds
• Alarm time = 5 seconds
• Invalidcode/tagstatustime=2seconds
• Re-lockdoor-active
• Re-lockonopening-active
• Door contact type - NC
• REX type NC
Parameters description:
• Door unlock timeisthemaximumactivationtimeforthelockingdevicerelayincaseofavalidcode/tagor
REXactivation.Denedinsecondsfrom1to255.
• Door open timeisthemaximumallowedtimeforthedoortobeleftopen.Thistimestartfromthemoment
ofunlockingthedoor,that’swhythemandatoryistobehigherthenthedoorunlocktime.Ifattheendof
thedoorunlocktimethedoorisstillopen,and“Doorstillopen”eventisgeneratedandloggedandalarm
relayisactivated.Ifyouwanttoletthedoortobeopenedforinnitetime,youshouldsetthistimeatdoor
opentimeto255.Denedinsecondsfrom1to255.
• Alarm Timeisthetimeforalarmrelayactivation.Itstartsfromthemomentofalarmgenerationandend
ofalarmcondition.Ifthedoorisforcedopenwhenalarmrelaywillbestillactiveforalarmtimeafterclosing
thedoor.Sameifthedoorisleftopen.
• Invalid code/card status timeisthetimeforthereaderstoshowtheinvalidstatusofacode/tagusing
LED’sandbuzzer
• Re-lock door-ifactivethedoorisre-lockedwhenitisclosedoropened,dependingofthefollowingsetting
• Relock on opening-isvalidonlyiftheprevioussettingisactive.Ifactivated,thedoorisre-lockedwhenthe
doorisopened,otherwisewhenitisclosing,withoutwaitingfordoorunlocktimetoexpire.
Codes/tags programming:
Forcodes/tagsprogrammingaMastercode/tagisneeded.Thiscanbekeyed/enrolledeitherbystandalonere-
setorbyaPC.Controllermemoryistableconstructed,from0upto511,where0isMasterposition.Werecom-
mendtokeepatableinthefollowingformattobeabletomadeacompletecode/tagprogramming.
Position Code/tag number User name
0 xx:xxxxx Mastercode/tag(4711-default)
1 xx:xxxxx User name 1
2 xx:xxxxx User name 2
... ... ...
511 xx:xxxxx User name 511
Withsystempowered,keyin/presentMastercode/tag.Thesystemgoesintostandaloneprogramming.Pro-
grammingphasesareindicatedbyLEDclippingandbuzzersounds,followedbyapprox.1secondpause.Each
keying/presentationofMastercode/tagputsthesysteminthenextprogrammingphase.
1. Oneshortactivation-keyin/enrollcode/tagintherstfreeposition
2. Twoshortactivations-deleteanexistingcode/tag
3. 3Threeshortactivations-deletealostordamagedtag
3

!!! ATTENTION - It is very important to know each code/tag position.
Program code/tag in the rst free position.
Withsystemon“Programcode/tagintherstfreeposition”keyin/presentthecode/tagyouwanttokeyin/en-
roll.Thiswillbestoredintherstfreepositioninthetable(writedowntheposition).Ifsomeerroroccurswhile
keying/enrolling,thesystemwillsignalwith“invalidcode/tag”,meaningthatthecode/tagisalreadystoredorthe
memory is full.
Afterprogrammingacode/tag,othercodes/tagscanbeprogrammeddirectly.
Delete an existing code/card.
Withthesystemon“Deleteanexistingcode/tag”keyin/presentthecode/tagyouwanttodelete.Thatcode/tag
willbedeletedfromthememoryandthatpositionbecomesfree.Writedownthatpositionasfreepsition.Ifde-
letioncannotbemadean“invalidcode/tag”signalwillbeshownonthereaders,meaningthatthecode/tagdid
notexistinthedatabase.Afterdeletingacode/tag,otherscanbekeyed/presentedtobedeleteddirectly.
Delete a lost/damaged tag.
Withthisoptionyoucandeleteatagwithouthavingthattag.Itisveryusefulincaseoflost/stolen/damaged
tags.Itispossibletodeleteatagwithoutdeletingallcodes/tagsandwithoutusingaPC-fullystandalone.In
thisphaseitisveryimportanttoknowtheuserpositionsinthedatabase.
Withthesystemon”Deletealost/damagedtag”presentthetaginthepositionlowerthanthecardwewnatto
delete.Forinstance,ifwewanttodeletetaginposition37wewillpresentthetaginposition36.Ifwedonthave
ataginposition36(36isfree)wewillpresentthetaginposition35andsoon.Inohterwords,thisphasecanbe
“Deletersttagenrolledafter(asposition)presentedtag”.
Again,itisveryimportanttonoteallpositionsoftagsenrolledordeleted.
Stand alone reset and Master code/tag programming.
TheMastercode/tagcanbeprogrammedinthefollowingsteps:
1. Powero
2. DisconnecttheCMinput
3. ShortcircuitawirebetweenLEDoutputandCMinput
4. Power on
5. Waitapprox.3secondsofLEDashing,thesystemgoesinto“Programcode/tag”phase,asshownbyLED/
buzzer
6. Keyin/presentthecode/tagthatyouwanttobecomeMastercode/tag
7. Atexitofprogramminguserphasepowerothesystem
8. RemovethewirebetweenCMandLED
9. ReconnecttheCMwirefromthemagneticcontact
10. Power on
Forsecurityreasons,alluserswillbedeletedbeforekeying/enrollingMastercode/tag.Thesystemgoesin“Pro-
gramcode/tag”andsinceallusersaredeleted,therstcode/tagprogrammedinposition0becomesMaster
code/tag.
ThankyouforchoosingConlan’sproducts.
Forfurtherassistance,pleasecontact
Oursupportservice.