9.Admin Card Operation
9.1 Add Card
10.User Operation
10.1 Acknowledging the Alarm
9.2 Delete Card
10.2 Reset to Factory Default
Note：
The Admin Delete card is used to delete card users continuously and quickly. When you
present the Admin Delete card,you will hear short "BEEP" sounds twice and the indicator light
turns orange. You have entered into Delete user programming mode.You can now present the
cards for deletion.When it is completed, you can present the Admin Delete card and you will
hear a long "BEEP" sound once and the indicator light turns red,indicating that you have exited
the Delete card user programming mode.
Note：
When the alarm is activated, users can acknowledge and stop the alarm by reading valid
user or Inputting valid fingerprint or pressing admin code.
Note：
Note: Registered user data won’t be deleted when reset to factory default.
Users can reset to device to its factory default if the Admin code is forgotten or the user wants
to place the device back to factory original settings.
Power off the device. Hold down the Exit button. Power on. Release the Exit button only when
you hear the beep sound twice. The Admin code has been reset to 999999, factory and the
device has defaulted to factory setting
To reset, follow the procedures below:
Function Operation steps Notes
Function Operation steps Notes
Read admin delete card Read the 1
st
user card Read the 2
nd
user card Read admin delete card
…
Read admin card Read valid user card Input valid fingerprint Press Admin code
Note：
The Admin Add card is used to add card users continuously and quickly. When you
present the Admin Add card. you will hear short "BEEP" sounds twice and the indicator light
turns orange. You have entered into Add user programming mode.You can present the cards for
programming now.After all the cards are added, present the Admin Add card again.You will hear
long "BEEP" sound once and the indicator light turns red, indicating that you have exited the Add
card user programming mode.
Read admin add card Read the 1
st
user card Read the 2
nd
user card Read admin add card
…
910
# #
*3 0
Admin code
# #
#
*60
Admin code
# #
*6 1
Admin code
# #
*6 2
Admin code
# #
*8 0
Admin code
# #
*81
Admin code
# #
*82
Admin code
# #
*8 3
Admin code
# #
*70
Admin code
# #
*7 1
Admin code
# #
*7 2
Admin code
#
#
*40-300
Admin code
#
#
*50-99
Admin code
# #
*31
Admin code
# #
*32
Admin code
# #
*3 3
Admin code
# #
*3 4
Admin code
# #
*35
Admin code
# #
*36
Admin code
Door unlock time
Door opening time range: 0-300S
0 equals to 50mS, factory default value
is 5S
Alarm time range: 0-99 min. Alarm time
set at 0 means no alarm. Factory default
value is 0
To put the device back to its default factory
operation mode
If enabled, the door will be kept open until
the exit button is pressed. To disable,
return the device back to standalone
access mode as above.
WG26 Output
Without alarm & locked function
Indicator light is on under standby
Indicator light is off under standby
Sound activated during the operation
No sound during the operation
The device will alarm if invalid cards or
codes were presented 10 times continuously
The device will be locked for 10 minutes if
invalid cards or codes are presented 10
times continuously
Alarm time
Reader mode
Locked mode
Alarm mode
Enable light indicator
Disable light indicator
Enable buzzer
Disable buzzer
Normal mode
Relay toggle mode
Standalone access
control mode
Card or facial
recognition or
fingerprint
Entry by card, fingerprint or
facial recognition(default value)
Multiple users
Fingerprint
Facial recognition
Card Entry by card only
Entry by fingerprint only
Entry by multiple cards/mutiple
faces/multiple fingerprints
Entry by card + fingerprint
Entry by Card +
Facial recognition
Entry by facial recognition only
Card + Fingerprint
Card +
Facial recognition
Access ways
Advanced Settings
or or or
