Connects2 Connects2Vision CAM-LR2-AD User manual

www.connects2.com
Application:
Land Rover Evoque 2011>, Range Rover 2004 - 2013,
Range Rover Vogue (L322) 2002 - 2012,
Discovery 2012 - 2014, Freelander 2013 - 2017
For Touch Screen Nav Version 3 (Resistive Touch), 3.1
(Capacitive Touch)
CAM-LR2-AD
Rear View Camera Input and Video In Motion

www.connects2.com
2
ABOUT THIS PRODUCT...
CAM-LR2-AD
Reversing Camera Add-On and Video in Motion Interface for Land Rover touch
screen navigation version 3 systems 2012>. Add on Camera interface designed to
allow the addition of an aftermarket reverse camera to the OEM screen -
compatible with NTSC cameras only.
Prior to Installation
Read the manual prior to installation. Technical knowledge is necessary for
installation. The place of installation must be free of moisture and away from heat
sources. Please ensure you use the correct tools to avoid damage to the vehicle or
product.
Connects2 can not be held responsible for the installation of this product.
Technical Support
Connects2 want to provide a fast and suitable resolution should you encounter any
technical issues. With this in mind, when contacting Connects2, try to provide as
much Information as possible. This will speed up the process and help us to help you.
Please use our dedicated online technical support centre: support.connects2.com
Subscribe to our YouTube Channel for installation
guides and tips... www.youtube.com/connects2

www.connects2.com 3
FITTING GUIDE
Dipswitch Settings
Vehicle/ navigation Dip 1 Dip 2 Dip 3 Dip 4 Dip 5 Dip 6
Video-in-motion permanent ON ON OFF OFF ON ON
Video-in-motion selective* OFF ON OFF OFF ON ON
* With Dip1 set to “OFF”, the included green cable is used to activate the
video in motion function
Dipswitch Functionality:
Dip 1 – Activation of Video in Motion
Dip 2 – Existing Rear View Camera
Dip 3 – TV icon simulation
Dip 4 – No function
Dip 5 – CAN-bus termination resistor on the vehicle side
Dip 6 – CAN-bus termination resistor on the head-unit side
Setting Dip2 to “ON” codes the factory rear-view camera input, which is located
on the brown fakra male connector of the factory monitor. When reverse gear is
engaged, the navigation will automatically switch to this input.

www.connects2.com
4
PIN-ASSIGNMENTS/CONNECTION DIAGRAM
Factory Monitor Connector Pin Assignment
Cable Colour Assignment
Orange/Grey CAN-HIGH Pin 2
Orange/Purple CAN-LOW Pin 1
8pin Molex Pin Assignment
Cable Colour Pin-No. Assignment
Yellow Pin 4 CAN-HIGH – connection to the head-unit
Blue Pin 3 CAN-LOW – connection to the head-unit
Yellow/Black Pin 8 CAN-HIGH – connection to the vehicle
Blue/Black Pin 7 CAN-LOW – connection to the vehicle
Red Pin 1 +12V Permanent
Black Pin 5 Ground
Green Pin 6 Activation of the video-in-motion function
(+12V = TV-free activated)
White Pin 2 Trigger output (+12V DC 500mA)
Connection Schema
Supplied
Adapter
Interface
Harness

www.connects2.com 5
INSTALLATION
NB: Before installation, switch off ignition, disconnect the vehicle battery and
remove the vehicle’s head unit.
The interface is installed behind the vehicle’s head unit. The RCA connectors
provide the factory aux signal and must remain connected.
Connecting Interface, harness and factory navigation monitor
1. Connect the female 8pin Molex connector of the harness to the male 8pin
Molex connector of the interface.
2. Transfer the female 16pin connector of vehicle harness from the rear of the
factory head unit into the male 16pin connector of the harness.
3. Plug the female 16pin connector of the harness into the male 16pin
connector on the rear of the factory navigation system.
Interface
Harness

www.connects2.com
6
INSTALLATION
Rear View Camera Connections
1. Connect the female Fakra-connector of the supplied adapter to the male
purple Fakra connector on the rear of the factory navigation monitor.
2. Connect the video RCA of the rear-view camera to the female RCA
connector of the supplied adapter
NB: Only compatible with NTSC-cameras.
Supplied
Adapter

www.connects2.com 7
VIDEO IN MOTION/SPECIFICATIONS
Activating Video in Motion
The video-in-motion can be activated and deactivated by Dip 1 or alternative-
ly by the included loose green cable in connection with a switch
(not included)
Video-in-motion permanent
With Dip1 set to “ON”, the video-in-motion function is permanently activated
Video-in-motion selective
With Dip1 set to “OFF”, the included green cable is used to activate the vid-
eo-in-motion function.
Connect a switch to the green cable and connect the green cable to +12V
ACC.
● +12V = Video in Motion is activated
● 0V = Video in Motuon is not activated
Note: The loose white cable is not required and must be isolated.

www.connects2.com
8
NOTES