Continental Fireplaces CDVS280N User manual

1
W415-0149 / D / 02.14.11
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.continentalfireplaces.com • ask@continentalfire.on.ca
1.24A
$10.00
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
SAFETY INFORMATION
!WARNING
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the supplier.
This appliance may be installed as an OEM
installation in manufactured home (USA only) or
mobile home and must be installed in accordance
with the manufacturer’s instructions and the
Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280, in the United
States or the Standard for Installation in Mobile
Homes, CAN/CSA Z240 MH, in Canada.
This appliance is only for use with the type(s) of
gas indicated on the rating plate. A conversion kit
is supplied with the appliance.
If the information in these instructions
are not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ANSI Z21.88 • CSA 2.33 FOR VENTED GAS FIREPLACE HEATERS.
CDVS280N & CS280N
NATURAL GAS
CDVS280P & CS280P
PROPANE
Model CS280 is made up of Model CDVS280 and B-Vent
Adapter Kit GS-150KT

2
W415-0149 / D / 02.14.11
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 GENERAL INSTRUCTIONS 5
2.3 GENERAL INFORMATION 7
2.4 RATING PLATE INFORMATION 8
3.0 VENTING 9
3.1 VENTING LENGTHS AND COMPONENTS 10
3.2 TYPICAL VENT INSTALLATION 11
3.3 SPECIAL VENT INSTALLATIONS 12
3.3.1 PERISCOPE TERMINATION 12
3.4 VENT TERMINAL CLEARANCES 13
3.5 VENTING APPLICATION FLOW CHART 14
3.6 DEFINITIONS 14
3.7 ELBOW VENT LENGTH VALUES 14
3.8 TOP EXIT HORIZONTAL TERMINATION 15
3.9 TOP EXIT VERTICAL TERMINATION 17
3.10 VERTICAL THROUGH EXISTING CHIMNEY 19
4.0 INSTALLATION 20
4.1 MINIMUM CLEARANCES TO COMBUSTIBLES 20
4.2 WALL AND CEILING PROTECTION 21
4.2.1 HORIZONTAL INSTALLATION 21
4.2.2 VERTICAL INSTALLATION 22
4.2.3 HORIZONTAL AIR TERMINAL INSTALLATION - MODEL CDVS280 22
4.2.4 VERTICAL AIR TERMINAL INSTALLATION 23
4.3 APPLIANCE VENT CONNECTION 24
4.4 MOBILE HOME INSTALLATION - MODEL CDVS280 24
4.5 GAS INSTALLATION 25
4.6 OPTIONAL WALL SWITCH / THERMOSTAT / REMOTE 25
4.7 B-VENT SPECIFICS 26
4.7.1 CHIMNEY INSTALLATION 26
4.7.2 INSTALLING "B" VENT 27
4.7.3 B-VENT 27
4.7.4 COMBUSTION AIR 28
4.7.5 ADDING VENT SECTIONS 28
5.0 FINISHING 29
5.1 DOOR CLOSING AND OPENING 29
5.2 LOG PLACEMENT 30
5.3 GLOWING EMBERS 31
5.4 CHARCOAL EMBERS 31
5.5 LOGO PLACEMENT 31
6.0 OPERATION 32
6.1 OPERATING/LIGHTING INSTRUCTIONS 33
7.0 ADJUSTMENT 34
7.1 PILOT BURNER ADJUSTMENT 34
7.2 VENTURI ADJUSTMENT 34
7.3 FLAME CHARACTERISTICS 35
7.4 RESTRICTING VERTICAL VENTS - MODEL CDVS280 35
8.0 MAINTENANCE 36
8.1 CARE OF GLASS 36
8.2 BLOWER REPLACEMENT 37
9.0 REPLACEMENTS 38
10.0 TROUBLE SHOOTING 42
11.0 WARRANTY 45
12.0 SERVICE HISTORY 46

3
W415-0149 / D / 02.14.11
Door, see “DOOR CLOSING /
OPENING” section.
Rating plate, see
“RATING PLATE” section.
Logo, see “LOGO
PLACEMENT” section.
Vent, see “VENTING” section.
1.0 INSTALLATION OVERVIEW

4
W415-0149 / D / 02.14.11
3.1C
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• ANY CHANGES TO THIS APPLIANCE OR IT’S CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
according to operating instructions could cause fire or injury.
• Risk of fire or asphyxiation do not operate appliance with fixed glass removed.
• Do not connect 110 volts to the control valve.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be
sharp.
• Do not burn wood or other materials in this appliance.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or
clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces.
These screens and guards must be fastened to the floor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• The appliance is a vented gas-fired appliance. Do not burn wood or other materials in the appliance.
• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance
and venting system are kept clean. The appliance and its venting system should be inspected before use and at least
annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting,
bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.
• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any gas control which has been under water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done
by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust
fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these
openings can also cause the surrounding combustible materials to overheat and catch fire.Only doors / optional fronts
certified with the unit are to be installed on the appliance.
• Only doors / optional fronts certified with the unit are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic
bags, these are not toys and should be kept away from children and infants.
• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as
having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated
temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a
T.V. or other electronic components.
• This appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by
Wolf Steel Ltd.
2.0 INTRODUCTION

5
W415-0149 / D / 02.14.11
2.1 DIMENSIONS
22 1/2”
11 1/4”
26 3/4”
7” Ø AIR
INTAKE
4” Ø
FLUE
18 1/2”
5 1/2”
17 3/4”12”10”
GAS LINE ACCESS HOLE
LOCATED IN PEDESTAL
BASE
VIEWING
AREA
2.2 GENERAL INSTRUCTIONS
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE
FRONT FACE OF THE UNIT.
SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT
WHEN THE APPLIANCE IS OPERATING.
FIRE RISK. EXPLOSION HAZARD.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE
TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG.
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.
USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING
COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
!
WARNING

6
W415-0149 / D / 02.14.11
4.1A
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to
conform with local codes. Installation practices vary from region to region and it is important to know the
specifics that apply to your area, for example in Massachusetts State:
• This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth
of Massachusetts.
• The appliance damper must be removed or welded in the open position prior to installation of a appliance
insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches.
• A Carbon Monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
A
NSI Z223.1 and NFPA 54 in the United States.
A
s long as the required clearance to combustibles is
maintained, the most desirable and beneficial location for an appliance is in the center of a building, thereby
allowing the most efficient use of the heat created. The location of windows, doors and the traffic flow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a floor or roof joist.
If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
® (NFI) as NFI Gas
Specialists
www.ncertied.org

7
W415-0149 / D / 02.14.11
2.3 GENERAL INFORMATION
CDVS280 CS280
NG LP NG LP
Altitude (FT) 0-4,500 0-4500 0-4500 0-4500
Max. Input (BTU/HR) 30,000 26,000 30,000 26,000
Max. Output (BTU/HR) 25,500 22,360 24,600 21,600
Max. Steady State
Efficiency (w/the fan
on)
85% 86% 82% 83%
Max. A.F.U.E. 76% 77%
Min. Inlet Gas Supply
Pressure
4.5" Water Column 11" Water Column 4.5" Water Column 11" Water Column
Max. Inlet Gas Supply
Pressure
7" Water Column 13" Water Column 7" Water Column 13" Water Column
Manifold Pressure
(Under Flow
Conditions)
3.5" Water Column 10" Water Column 3.5" Water Column 10" Water Column
When the appliance is installed at elevations above 4,500 ft, and in the absence of specific recommendations from
the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each
additional 1,000 ft.
Change in flame appearance from "HI" to "LO" is more evident in natural gas than in propane.
Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.
This appliance may be installed in an aftermarket permanently located, manufactured mobile home, where not
prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases, unless a certified kit is used.
This appliance is approved for bedroom and bed-sitting room installations.
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION
AND QUALITY!

8
W415-0149 / D / 02.14.11
INSTALLER: It is your
responsibility to check off the
appropriate box on the rating
plate according to the model,
venting and gas type of the
appliance.
For rating plate location, see
“INSTALLATION OVERVIEW”
section.
This illustration is for reference
only. Refer to the rating plate on the
appliance for accurate information.
MODEL CDVS280/GDS28 APPROVEDFOR BEDROOM,
BATHROOM & BEDSITTING ROOM INSTALLATION. SUITABLE
FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCOR-
DANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH
SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN
THE UNITED STATES THE MANUFACTURED HOME
CONTRUCTIONANDSAFETYSTANDARD,TITLE24CFR,PART
3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE
THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANU-
FACTURED HOME INSTALLATIONS, SITES AND COMMUNI-
TIES, ANSI / NFPA 501A.
HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A
COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE
POUR INSTALLATION DANS UNE MAISON MOBILE SI SON
INSTALLATION CONFORME AUX EXIGENCES DE LA NORME
CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES
AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE
LA NORME DE SECURITE ET DE CONSTRUCTION DE
MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280.
DANS LE CAS OU CETTE NORME D'ETATS-UNIS NE PEUT
ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVE AU
CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE
POUR LES INSTALLATIONS DANS LES MAISONS MANUFAC-
TURES,LES SITES ETLESCOMMUNAUTES,ANSI/NFPA501A
.
STEADY STATE EFFICIENCY (NG): 75% FAN OFF / 78% FAN ON
STEADY STATE EFFICIENCY (LP): 75% FAN OFF / 79% FAN ON
EFFICACITE CONSTANTE (GN): 75% VENT.ARRETE
78% VENT. FONCTIONNE
EFFICACITE CONSTANTE (GP): 75% VENTILATEURARRETE
79% VENTILATEUR FONCTIONNE
STEADYSTATEEFFICIENCYAPPLIES TOCANADAONLY / L'EFFICACITE
CONSTANTE S'APPLIQUENTSEULEMENTAU CANADA.
AFUE (NG/LP) (GN/GP): 64% / 65%
MINIMUMAND MAXIMUM HORIZONTALVENT LENGTHSARE
25 INCHES AND 20 FEETRESPECTIVELY. LES LONGUEURS
HORIZONTALES MINIMALE ET MAXIMALE SONT 25 POUCES
ET20 PIEDS RESPECTIVEMENT.
THE APPLIANCE MUST BE VENTED USING THE APPROPRI-
ATE NAPOLEON VENT KITS. SEE OWNERS INSTALLATION
MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLA-
TION AND RESEALING IS NECESSARY AFTER SERVICING
THE VENT-AIR INTAKE SYSTEM.
L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT
L'ENSEMBLE D'EVACUATION PROPRE A NAPOLEON.
REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE
POUR L'EVACUATION PRECISE. ILEST IMPORTANT DE BIEN
REINSTALLER ET RESCELLER L'EVENT APRES AVOIR AS-
SURE LE MAINTIEN DU SYSTEME DE PRISE D'AIR.
W385-0165 / F
SERIALNUMBER
NO.DESERIE
MANIFOLDPRESSURE:3.5INCHESW.C.(NG)/10INCHESW.C.(LP)
PRESSIONAU COLLECTEUR: 3.5"D'UNECOLONNED'EAU(GN)
10" D'UNE COLONNE D'EAU (PG)
MIN SUPPLY PRESSURE: 4.5" W.C.(NG) / 11" W.C. (LP)
PRESSIOND'ALIMENTATIONMIN:4.5"D'UNECOLONNED'EAU(GN)
11" D'UNE COLONNE D'EAU (PG)
MAX. SUPPLY PRESSURE: 7" W.C. (NG) / 13" W.C. (LP)
PRESSIOND'ALIMENTATIONMAX:7"D'UNECOLONNED'EAU(GN)
13" D'UNE COLONNE D'EAU (PG)
FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNITONLY.
UTILISER AVEC LES PORTES VITREES HOMOLOGUEES
SEULEMENTAVECCETTEUNITE.
WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE,
WHICHWILLCOMEINCONTACTWITHTHEFLAMES,OTHERTHAN
THATSUPPLIED BYTHE MANUFACTURERWITHTHEAPPLIANCE.
AVERTISSEMENT: N'AJOUTEZ PASACETAPPAREILAUCUN
MATERIAU DEVANT ENTRER EN CONTACT AVEC LES
FLAMMES AUTRE QUE CELUI QUI ESTFOURNI AVEC CET
APPAREIL PAR LE FABRICANT.
MINIMUMCLEARANCETO COMBUSTIBLE MA
DEGAGEMENTSMINIMAUXDESMATERIAUX
A7" D17½"
B2" E6¼"
C1" F9½"
20"TO CEILINGFROMSTOVE TOP
20" ENTRE LE DESSUS DU FOYER ET LE PLAFOND
ELECTRICAL RATING / CLASS.: 115V 1.5AMP 60HZ
MODEL CS280/GS28 APPROVED FOR BEDROOM, &
BEDSITTING ROOM INSTALLATION. HOMOLOGUE POUR IN-
STALLATION DANS UNE CHAMBRE A COUCHER, & UN
STUDIO.
STEADY STATEEFFICIENCY(NG): 80% FANOFF /82% FANON
STEADY STATEEFFICIENCY(LP): 80%FAN OFF / 83%FAN ON
EFFICACITE CONSTANTE (GN): 80% VENT.ARRETE
82% VENT. FONCTIONNE
EFFICACITECONSTANTE(GP): 80% VENTILATEURARRETE
83% VENTILATEUR FONCTIONNE
STEADYSTATEEFFICIENCYAPPLIESTOCANADAONLY /L'EFFICACITE
CONSTANTE S'APPLIQUENTSEULEMENTAU CANADA.
AFUE (NG/LP) (GN/GP): 66% / 68%
THISAPPLIANCEMUSTBEINSTALLEDUSINGANADAPTERKIT
GS-150KT. CETAPPAREIL DOIT ETRE INSTALLE EN UTILISANT
UNENSEMBLEADAPTATEURGS-150KT.
NOT FOR USE WITH SOLID FUEL
UN COMBUSTIBLE SOLIDE NE DOIT PAS
ETRE UTILISEAVEC CET APPAREIL GDS28
ALTITUDE/ELEVATION
INPUT / ALIMENTATION
REDUCED INPUT /ALIMENTATION REDUITE
OUTPUT(CDVS280/GDS28)RENDEMENT
OUTPUT(CS280/GS28)RENDEMENT
DIRECTVENTMODEL
‘B’VENTMODEL
0-4500FT (0-1370m)
30,000 BTU/h
18,000 BTU/h
22,500 BTU/h
24,000 BTU/h
0-4500FT(0-1370m)
26,000 BTU/h
15,000 BTU/h
19,500 BTU/h
20,800 BTU/h
CERTIFIEDUNDER:CSA2.33-2009, ANSIZ21.88-2009 VENTEDGASFIREPLACEHEATER.
HOMOLOGUE SELON LES NORMES: CSA2.33-2009 , ANSI Z21.88-2009 FOYER DE CHAUFFAGE AU GAZAVEC EVACUATION.
CDVS280-N
CS280-N
GDS28-N
GS28-N
GDS28-P
GS28-P
CDVS280-P
CS28-P
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA
2.4 RATING PLATE INFORMATION
SAMPLE
8
APPROVEDAPPROV
ROOMOOM
IN
SINS
T
ALLLL
T
AA
TIOT
AA
LLLL
AA
TIOTIO
AAA
NN
IF I
NN
SS
TT
AA
TT
T
L
LLL
E
D
RENREN
TT
SS
TT
ANDARDANDARD
TT
T
CAN/CSCAN/CS
AA
ED
MO
BIL
EOBILE
HO
MES,
HOMES
I
N
CANADA
CANADA
T
A
TE
S
TH
EHE
M
AN
UMANU
F
F
ACTUREDCTURED
AND
S
AFE
T
Y
S
T
ANDARD,ANDARD,
T
TITLETITLE
2424
TT
HH
I
SIS
U
S
S
T
A
T
NDA
R
DI
SIS
NN
OO
TT
APPAPP
DARDDARD
F
ORFO
FIR
E
S
AFE
T
Y
CRITERCRITE
EDD
HO
M
EHOME
IN
SINS
T
ALL
T
A
TIONS,ONS,
A
SITETE
ANSI
/
NF
NF
PP
AA
PPP
501501
A
A
..
MOLOGUEMOLOGUE
P
OUROUR
IN
SINS
TT
ALLALL
TT
T
AA
TIONTION
AA
A
C
OO
UCHUCH
EE
RR
,,
UNUN
E
S
A
A
L
LLL
EE
D
D
EE
BAI
BAI
NN
ETE
POURPOUR
IN
SINS
TT
ALLALL
TTT
A
TIONN
A
DAN
SDANS
UNU
I
I
NN
SS
TT
A
T
L
L
AA
TIOTIO
AA
A
NN
C
O
N
F
O
R
M
RM
EE
AA
C
AN
/CS
A
CAN/CSA
Z24
0
M
HZ240
S
ERI
E
D
A
UAU
G
AZ,
GAZ,
E
NEN
VI
GU
E
UR
A
LA
LA
NN
OO
R
M
ERME
D
E
SEC
M
AI
SO
N
SAISONS
MANUFAMAN
DAN
SDANS
L
ELE
C
A
SCAS
OO
ETREETR
APPLIQUPPLIQ
CRCR
IT
EITE
R
E
DD
P
OURPOUR
LEL
TURESURES
STEAS
STS
E
..
CU
NN
C
LELE
S
VECEC
CECE
TT
ER
E
T
L
E
PLAF
ONAFON
D
D
ASS.:SS.:
11
1
5V15
1.
5
AM
P
60H60H
Z
Z
280/GS2880/G
APPR
O
VED
APPROVED
F
ORFOR
BEBE
ROOMROOM
IN
SINS
TT
ALL
T
A
L
TIONON
A
..
HH
OO
MM
OO
L
OG
U
ONON
DAN
SDANS
U
N
ENE
C
HAMBR
EMBRE
A
A
CO
O
.
AD
Y
SS
TT
AA
TT
T
TT
AA
A
EE
E
FFI
C
IEN
CEFFICIENC
Y
Y
(
NG
):(NG)
8
00
%%
Y
SS
TT
AA
TTT
TETE
AAA
E
FFI
C
IEN
CEFFICIENC
Y
Y
(
LP
):(LP)
8
0
ITETE
CON
SCONS
TT
ANTETE
T
(GN):(GN)
OO
NN
SS
TT
ANAN
TTT
TETE
((
GG
ENC
AM
AM
AM
AM
AM
AM
M
AM
AM
AM
AM
AM
M
M
AM
M
M
M
M
M
M
M
M
M
AM
M
M
SAMPLE
S

9
W415-0149 / D / 02.14.11
3.0 VENTING
7.1A
THIS APPLIANCE USES A 4” EXHAUST / 7” AIR INTAKE VENT PIPE SYSTEM.
Refer to the section applicable to your installation.
For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the
minimum vertical vent length can create difficulty in burner start-up and/or carboning. Under extreme vent
configurations, allow several minutes (5-15) for the flame to stabilize after ignition. Provide a means for
visually checking the vent connection to the appliance after the appliance is installed. Use a firestop, vent pipe
shield or attic insulation shield when penetrating interior walls, floor or ceiling.
NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions
provided for the initial installation.
!
WARNING
RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.
IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3 FEET
FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT
NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM
COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0370 OR EQUIVALENT
NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES
FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT
PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS
REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF
EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.
A terminal shall not terminate directly above a sidewalk or paved driveway which is located between
two single family dwellings and serves both dwellings. Local codes or regulations may require different
clearances.
Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled
tight. A 1-1/4" air gap all around between the inner liner and outer appliance pipe is required for safe
operation. Use a firestop when penetrating interior walls, floor or ceiling.

10
W415-0149 / D / 02.14.11
3.1 VENTING LENGTHS AND COMPONENTS
Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting
components. Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal
locations for either system are set out in this manual and must be adhered to. For Simpson Dura-Vent, Selkirk
Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure provided with the venting
components.
A starter adaptor must be used with the following vent systems and may be purchased from the corresponding
supplier:
* For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the
installation procedure found on the website for your venting supplier.
For vent systems that provide seals on the inner exhaust flue, only the outer air intake joints must be sealed using a
red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent
pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance flue collar
which must be sealed using the black high temperature sealant Mill Pac.
When using Wolf Steel venting components, use only approved Wolf Steel termination kits: wall terminal kit GD175
(7/12’ of venting included), or 1/12 to 7/12 pitch roof terminal kit GD110, 8/12 to 12/12 roof terminal kit GD111, flat
roof terminal kit GD112 or periscope kit GD180 (for wall penetration below grade) in conjunction with the appropriate
venting components.
For optimum flame appearance and appliance operation, keep the vent length and number of elbows to a
minimum. It is recommended that all horizontal runs have a minimum 1/4” rise per foot. The air terminal must
remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed
and undamaged. Rigid and flexible venting systems must not be combined. Different venting manufacturers
components must not be combined.
These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run
is 20 feet. The maximum allowable vertical vent length is 40 feet. The maximum number of vent connections is two
horizontally or three vertically (excluding the appliance and the air terminal connections) when using flexible venting.
Deviation from the minimum vertical vent length can create difficulty in burner start-up and/or carboning.
Use an adjustable pipe as the final length of rigid piping to the stove for ease of installation.
PART 4”/7” SUPPLIER WEBSITE
Duravent GDS924N Wolf Steel www.duravent.com
Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com
Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com
SuperSeal 4DNA Metal-Fab www.mtlfab.com
8.5