Contractors Wardrobe Style Lite Vanity Flair User manual

Installation Instructions
Model
Style Lite
®
Vanity Flair
Contractors Wardrobe®
DESIGNERS • MANUFACTURERS • TOLL FREE: (800) CW-DOORS • [phone] • www.cwdoor.com
26121 Avenue Hall • Valencia, CA 91355 • [phone] • FAX: [phone]
Style Lite Vanity Flair Instr. 2/3/09 5:18 PM Page 1

Illustrated Parts Breakdown (IPB)
Model Style Lite®Vanity Flair
NO. QTY PART # PART DESCRIPTION
#1 3 Mirrored Glass Panels
#2 6 A3510 Top Mold / Bottom Mold with 2-Way Tape
#3 6 A3510 Side Mold
#4 2 HMBFA Mirror Handles with 2-Way Tape
#5 12 50075 #8 x 1″Corner Screw
#6 4 H6020 Pivot Hinges
#7 24 S0055 #8 x 1/2″Screw
#8 2 A6000 Bracket
#9 6 S0084 #6 x 3/8″Screw
#10 2 S0180 Anchors
#11 8 S0095 #8 x 1-1/2″PH SMS Screw
#12 2 C2060 Wing Clips
#13 2 S0130 #6 x 3/4″Clip Catch Screw
2Style Lite®Vanity Flair - 0209
3
13 12
2
4
3
3
3
4
13
12
3
5
2
7
6
7
6
2
5
2
5
7
6
7
6
2
2
5
3
9
9
9
9
8
11
11
11
11
1
1
1
Style Lite Vanity Flair Instr. 2/3/09 5:18 PM Page 2

Congratulations on purchasing your new CW®Style Lite®
Vanity Flair. Now that you have opened the package, we
want you to verify that you have all the necessary hard-
ware supplied with your vanity.
PARTS CHECK LIST:
NO. QTY DESCRIPTION
(#1) 3 Mirrored Glass Panels
(#4) 2 Mirror Handles
with 2-Way Tape
(#10) 2 Anchors
(#11) 8 #8 x 1-1/2″PH SMS Screws
(#12) 2 Wing Clips
(#13) 2 #6 x 3/4″Clip Catch Screws
If you find that any parts are damaged or missing, refer to
the parts list and IPB Drawing and contact
Contractors Wardrobe® ’ s Customer Service Department
at [phone].
TOOL CHECK LIST
You will need:
• Phillips Screwdriver
• Tape Measure
• Hammer
• Pencil
• 3/8″Drill Motor and 3/16″and 1/8″Drill Bits
• Square or Level
Style Lite®Vanity Flair - 0209
STEP 2 Mounting the Vanity Flair
Place the Mirrored Glass Panels (#1) against
the wall where you want to install it. Open the
left wing and mark the wall through all the holes
in the Bracket (#8). Next, open the right wing
and mark the wall through all the holes in the
Bracket (#8). Next, move the Mirrored Glass
Panels (#1) out of the way. Carefully drill a 1/8″
hole in the wall where you marked the holes
through the Bracket (#8). If you did not drill into
a wooden stud, you will need to use wall
anchors. After you drill all of the holes and
install the anchors, if necessary, move the
Mirrored Glass Panels (#1) back into place.
Next, insert the #8 x 1-1/2″PH SMS Screws
(#11) through the holes in each Bracket (#8).
STEP 3 Installing the Wing Clips
Your next step is to install your Wing Clips (#12)
to the wall. Place a Wing Clip (#12) at the upper
right corner of the right wing. With a Pencil
mark a hole in Wing Clip (#12). Open vanity
wing and install #6 x 3/4″Clip Catch Screw
(#13) and Wing Clip (#12). Repeat this on the
left wing as well using #6 x 3/4″Clip Catch
Screw (#13) and Wing Clip (#12). This Wing
Clip (#12) will hold the vanity wings against
the wall.
STEP 4 Installing the Mirror Handles
Clean mirror in the area where the Mirror Handles
(#4) will be applied. Peel paper off the back of the
Mirror Handles (#4). Position each Mirror Handle
(#4) 36″from the bottom of the Mirrored Glass
Panels (#1) and 1-1/2″from Side Mold (#3) on
each Mirrored Glass Panel (#1). (See drawing on
Page 2).
INSTALLING THE STYLE LITE ®VANITY FLAIR
STEP 1 Measure for Center of Opening
Place Mirrored Glass Panels (#1) onto back
splash. Using a Tape Measure, measure left
and right sides to find center of opening (You
may need a second person to hold the Mirrored
Glass Panels (#1) in place, while measuring the
opening to find the center).
Thank you for purchasing a CW®Wardrobe Door. This
is only part of a large line of wardrobe doors and high
quality bath enclosure products. If you like this product,
please contact Contractors Wardrobe®for more
information about our many beautiful bath enclosures
available in a vast array of colors and finishes to suit
your designing needs.
3
Style Lite Vanity Flair Instr. 2/3/09 5:18 PM Page 3