Contractors Wardrobe uDivide User manual

Partition & Divider System
™
Parts and Assembly Instructions
Sample of uDivide™ configuration shown above.
Assembly Video
QR Link

PART NUMBER
DESCRIPTIONQTY
ITEM
5970SC
F2050
A5900MF144
A5930SC153
S83125
A5910SC292
A5910SC292
AIS - 2323**
A5960
S0153
P4100CL
A5950SC
S82075
W8011
Base Plate
Aluminum Square Stem
Felt 1/16” Pads with Adhesive
One Sided Round Post
#8 x 3/8” FH Screw
Frame Bar - Horizontal
Frame Bar - Vertical
**
**
**
**
23-1/2” x 23-1/2” Insert Sheet
23-1/2” x 23-1/2” Insert Sheet
Aluminum Divider Lock 2 PC
10-24 3/8” Phil Pan Set Screw
N6080
B0060
Rigid PVC Glide Strip
Aluminum Post Cap
Wrench - 5mm Hex Key
10-24 Weld Nut
Rubber Bumper / Screw
#8 1-1/2” FH SMS Screw
2
A
2
6
B
C
2
2
4
D
E
G3
F
1
1
1
H
AIS - 2348**
I
2
4
1
J
K
M
N
O
P
Q
L
A
Q
B
G
L M
K
C
IH
D
E
OF
N
P
D
J
IH
Black-BLA
Blue-BLU
Green-GRE
Orange-ORA
Red-RED
White-WHT
Yellow-YEL
Bronze Translucent-BZT
Alpine Oak-ALO
Cherry-CHE
Clear Fir-CLE
Maple-MAP
Walnut-WAL
Wheat Oak-WHO
Chalkboard-CHA
*Dry Erase-DRE
*Note: We recommend Expo
®
Low Odor
dry erase markers. Test all other markers
before using them.
**Insert quantity varies on the size and configuration of your uDivide™
Set Screw
Sample of uDivide™ configuration shown above.
Illustrated Parts Breakdown (IPB)
Model uDivide™
Page 2

Option. You can choose to lock the Main Post to the base and Square Post by
using the provided screws to fasten them together, as shown in Fig #2.
3
Repeat these steps for other Post assembly.
4
Fig #2
Set Screw
2
Square Post
Round Post
Stem Post
Connect the Base Plate to the Square Stem using the
two screws provided. Countersunk holes should be
facing down to the oor.
1
Base
Screws
Felt
Pad
Slip Square Post into Round Post slot making sure the
slot in the Round Post is facing as shown in Fig #1. Align
the hole in the Square Post with the hole in the Round Post.
Fig #1
Assembling Horizontal Bars, Vertical Bars and Panel Inserts
Page 3

The Hex Key is used to tighten the framework together
as you assemble your uDivide™. Make sure the
Glide Strip
is rmly in place to help cushion your Insert Panels.
7
Fig #3
First locate the Horizontal Bar with one (1) Glide Strip and
slide it into place at the bottom of the two Round Post
slots as shown in Fig #3.
6
Fig #4
8
Remember to peel away all protective lm from Insert
Panels before Assembling. Slide Panels down inside the
vertical slots of the Round Posts on top of the Horizontal
Bar. If your congurations include Vertical Bars then insert
the middle Vertical Bar with Glide Strips as shown in Fig #4.
5
Locking Assembly
Horizontal / Vertical Bar
To install locking assemblies into
the horizontal frame bars, rst
remove the Hex Screw, then place a
Locking Assembly into the end of
the bar and insert the Hex Screw
back into the Locking Assembly
Page 4

Repeat these steps for assembling all Horizontal
and Vertical Bars; remember to tighten all
Hex Screws.
9
Post Caps
Install Post Caps by removing backing of the
two-way tape provided.
10
Note: We recommend Expo
®
Low Odor dry erase markers.
Test all other markers before using them.
Page 5
Final Assembly

™
®
®
Contractors Wardrobe
®
Designers & Manufacturers
®
Contractors Wardrobe
®
26121 Avenue Hall, Valencia, CA 91355 Phone: [phone] Fax: [phone] www.CwDoor.com