STEP 2 Mounting the Vanity Flair
Place the Mirrored Glass Panels (#1) against
the wall where you want to install it. Open the
left wing and mark the wall through all the holes
in the Vanity Bracket (#8). Next, open the right
wing and mark the wall through all the holes in
the Vanity Bracket (#8). Next, move the
Mirrored Glass Panels (#1) out of the way.
Carefully drill a 1/8″hole in the wall where you
marked the holes through the Vanity Bracket
(#8). If you did not drill into a wooden stud, you
will need to use wall anchors. After you drill all
of the holes and install the anchors, if
necessary, move the Mirrored Glass Panels
(#1) back into place. Next, insert the #8 x 1-1/2″
PH SMS Screws (#11) through the holes in each
Vanity Bracket (#8).
STEP 3 Installing the Wing Clips
Your next step is to install your Wing Clips (#12)
to the wall. Place a Wing Clip (#12) at the upper
right corner of the right wing. With a Pencil mark
a hole in Wing Clip (#12). Open vanity wing and
install #6 x 3/4″ Clip Catch Screw (#13) and
Wing Clip (#12). Repeat this on the left wing as
well using #6 x 3/4″ Clip Catch Screw (#13) and
Wing Clip (#12). This Wing Clip (#12) will hold
the vanity wings against the wall.
STEP 4 Installing the Mirror Handles
Clean mirror in the area where the Mirror Handles
(#4) will be applied. Peel paper off the back of the
Mirror Handles (#4). Position each Mirror Handle
(#4) 36″from the bottom of the Mirrored Glass
Panels (#1) and 1-1/2″from Side Mold (#3) on
each Mirrored Glass Panel (#1). (See drawing on
Page 2).
3Trim Line®Vanity Flair - 0109
INSTALLING THE TRIM LINE ®VANITY FLAIR
STEP 1 Measure for Center of Opening
Place Mirrored Glass Panels (#1) onto back
splash. Using a Tape Measure, measure left
and right sides to find center of opening (You
may need a second person to hold the Mirrored
Glass Panels (#1) in place, while measuring the
opening to find the center).
Thank you for purchasing a CW®Wardrobe Door. This
is only part of a large line of wardrobe doors and high
quality bath enclosure products. If you like this product,
please contact Contractors Wardrobe®for more
information about our many beautiful bath enclosures
available in a vast array of colors and finishes to suit
your designing needs.
Congratulations on purchasing your new CW®Trim Line®
Vanity Flair. Now that you have opened the package, we
want you to verify that you have all the necessary hard-
ware supplied with your vanity.
PARTS CHECK LIST:
NO. QTY DESCRIPTION
(#1) 3 Mirrored Glass Panels
(#4) 2 Mirror Handles
with 2-Way Tape
(#10) 2 Anchors
(#11) 8 #8 x 1-1/2″PH SMS Screws
(#12) 2 Wing Clips
(#13) 2 #6 x 3/4″Clip Catch Screws
If you find that any parts are damaged or missing, refer to
the parts list and IPB Drawing and contact
Contractors Wardrobe ®
’
s Customer Service Department
at (661) 257-1177.
TOOL CHECK LIST
You will need:
• Phillips Screwdriver
• Tape Measure
• Hammer
• Pencil
• 3/8″Drill Motor and 3/16″and 1/8″Drill Bits
• Square or Level
Trim Line Vanity Flair Instr. 1/21/09 3:16 PM Page 3
