Contura Surround C 11 User manual

Installation
instruction
Surround C 11
Surround C 21
www.contura.eu

GB
38 CERTIFICATE
PRODUCT
Product type Stove lit with solid biofuels
Type designation Contura 11
Manufacturing number See rating plate on the stove
Intended area of use Heating of rooms in residential buildings
Fuel Wood
MANUFACTURER
Name NIBE AB / Contura
Address Box 134, Skulptörvägen 10
SE-285 23 Markaryd, Sweden
CHECKS
According to AVCP System 3
European standard EN 13240:2001 / A2:2004
Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,
has checked declared performance and issued test report no. RRF-40 09 2080
PERFORMANCE DECLARATION
No. C11-CPR-130614-SE-1
DECLARED PERFORMANCE
Essential characteristics Performance Harmonised technical
specification
Reaction to fire A1 WT
Minimum distance to combustible material No minimum distance to rear
400 mm to side
Other safety distances according to
the installation instructions
Risk of falling embers Approved
Emissions from combustion CO 0.09%
NOx 109 mg/m3
OGC 50 mg/m3
PM 29 mg/m3
Surface temperatures Approved
Cleaning options Approved
Mechanical durability Approved
Emissions of hazardous substances Approved
Nominal output 9 kW
Efficiency 81%
Flue gas temperature in connector at nominal
output
290°C
EN 13240:2001 / A2:2004
The undersigned is responsible for the manufacture and conformity with the declared performance.
Niklas Gunnarsson, Business area manager NIBE STOVES
Markaryd, 1st July 2013

GB
39
CERTIFICATE
PRODUCT
Product type Stove lit with solid biofuels
Type designation Contura 21
Manufacturing number See rating plate on the stove
Intended area of use Heating of rooms in residential buildings
Fuel Wood
MANUFACTURER
Name NIBE AB / Contura
Address Box 134, Skulptörvägen 10
SE-285 23 Markaryd, Sweden
CHECKS
According to AVCP System 3
European standard EN 13240:2001 / A2:2004
Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,
has checked declared performance and issued test report no. RRF-40 09 1081
PERFORMANCE DECLARATION
No. C21-CPR-130614-SE-1
DECLARED PERFORMANCE
Essential characteristics Performance Harmonised technical
specification
Reaction to fire A1 WT
Minimum distance to combustible material No minimum distance to rear
400 mm to side
Other safety distances according to
the installation instructions
Risk of falling embers Approved
Emissions from combustion CO 0.07%
NOx 99 mg/m3
OGC 42 mg/m3
PM 29 mg/m3
Surface temperatures Approved
Cleaning options Approved
Mechanical durability Approved
Emissions of hazardous substances Approved
Nominal output 10 kW
Efficiency 81%
Flue gas temperature in connector at nominal
output
330°C
EN 13240:2001 / A2:2004
The undersigned is responsible for the manufacture and conformity with the declared performance.
Niklas Gunnarsson, Business area manager NIBE STOVES
Markaryd, 1st July 2013

GB
40
A warm welcome to Contura
A warm welcome to the Contura family. We hope you will
get a great deal of pleasure from your new stove. As a new
owner of a Contura stove you have secured a product
with timeless design and long service life. Contura also
has combustion that is both environmentally friendly and
efficient for the best heat production.
Read through these installation instructions carefully before
installation. Read how to best light your stove in the lighting
instructions.
NOTE!
Report the installation of a stove to
your local authority
The owner of the house is personally responsible for ensuring
compliance with the mandatory safety requirements and
must have the installation approved by a qualified inspector.
Your local chimney sweep must also be informed about
the installation as this will affect the routines for regular
chimney-sweeping services.
WARNING!
The stove becomes very hot
During operation, certain surfaces of the stove become
very hot and can cause burn injury if touched. Be aware of
the strong heat radiated through the hatch glass. Placing
flammable material closer than the safe distance indicated
may cause a fire. Pyre lighting can cause quick gas ignition
with the risk of damage to property and personal injury.
CONTENTS
Table of contents
Technical details 41
Supply of combustion air 42
Installation distance to walls and ceiling 43
Installation alternatives 45
Installing the surround 47
Installing the height extension 58
Flammable wall and accompanying protective screen
Installing the height extension 62
Non-flammable wall and chimney connection straight back
or straight up
Installing the height extension 65
Non-flammable wall and connection with angle back
Installing the woodbox 69

GB
41
Technical details
C11 C21
Power output 6-12 kW 6-12 kW
Nominal output 9 kW 10 kW
Efficiency 81% 81%
Model C11C C11A/S
Weight (kg) 470 450
Width (mm) 1050 1050
Depth (mm) 620 620
Height (mm) 1620 1620
Model C11C extended C11A/S extended
Weight (kg) 575 550
Height (mm) 2305 2305
Model C21C C21A/S
Weight (kg) 495 480
Width (mm) 950 950
Depth (mm) 620 620
Building application
Before installing a stove or erecting a chimney it is necessary for you
to make a building application permission to your local authority. Ask
your local authority for advice regarding building regulations and the
application.
Structural support
If the hearth is to be positioned on a wooden joist, a structural
engineer should evaluate the load capacity of the floor. When the
gross weight exceeds 400 kg, reinforcement of the wooden joists is
usually necessary.
Hearth plate
If the floor under the hearth is flammable, it must be protected by
a non-flammable material which covers at least 300 mm to the front
and 100 mm on each side.
The hearth plate can consist of natural stone, concrete or 0.7 mm
thick metal. A painted metal or glass hearth plate is available as an
accessory.
Chimney
The insert requires a draft in the chimney of at least –12 Pa. The
draft is affected both by the length and area of the chimney, and by
how well sealed it is.
• Once the lighting phase is complete, this insert must be operated
with the door closed because of the risk of smoke entering the room.
Always open the door carefully and slowly to prevent blow back
because of the changing pressure in the stove.
• Carefully check that the chimney is sealed and that there is no
leakage around soot hatches and flue connections.
Note that a flue with sharp bends and horizontal routing reduces
the draught in the chimney. Maximum horizontal flue is 1 m, on the
condition that the vertical flue length is at least 5 m. It must be
possible to sweep the full length of the flue and the soot hatches
must be easily accessible.
Wall behind
If your Contura 11 / 21 is to be installed against a flammable wall the
wall must be protected by a firewall or by the integrated protective
screen that is sold an as accessory for these models. A firewall
must be at least the same width and height as the surround. More
information about the requirements made of the fire wall material is
available in the separate instructions for the insert. Remember that
non-flammable walls can also require protection if they are bearing
walls or have flammable material behind them.
Concrete
The surface of concrete, by its nature, is not free of defects. In
order to achieve a neat end result some of the concrete may need to
be filled and sanded. If greater damage occurs to the concrete it can
be repaired by mixing water with the cement powder supplied and
filling the holes.
Because of the settling in buildings and the fact that concrete
shrinks, cracks may occur in the grouting between the blocks in the
first few months. Scrape out the grout and brush the surfaces clean.
Fill with new grout and paint over when dry.
Height (mm) 1755 1755
Model C21C extended C21A/S extended
Weight (kg) 585 560
Height (mm) 2305 2305
Connector diameter Ø200 mm ext.
Tested in accordance with:
European standard EN-13240
DIN plus
Bauart 1
Art. 15a B-VG
Test report no.
C11: RRF 40 09 2080
C21: RRF 40 09 2081
General
This manual contains instructions about how the Contura 11 and 21
must be constructed and installed. More information about the insert is
available in the separate installation instructions. To ensure the function
and safety of the hearth, we recommend that installation is carried
out by an authorised technician. Our Contura dealers can recommend
suitable technicians, information about our dealers can be found at www.
contura.eu
Instructions for lighting are also supplied with the insert. Read them
carefully and keep them safe for future use.
The hearth is type approved in accordance with EN 13240 and must be
connected to a chimney dimensioned for a flue temperature of 350°C,
the external connection diameter is Ø200 mm. Supply of combustion air
from the outside must be arranged, see page 42.
Woodbox
135
610
620
465
Woodbox
110
465
620
465
FACTS

GB
42
Knockout
To insert the combustion air hose through the base plate, tap
out the knockout from the concrete using a hammer, remember
to protect the floor.
HK
HK
HK
HK
Supply of combustion air
Combustion air can be provided directly via a duct from outside, or
indirectly via a vent in the outer wall of the room where the stove is
to be placed. The amount of combustion air used for combustion is
approximately 30 m³/h (applies with closed hatch),
Some installation alternatives are shown to the right. The air duct
connection on the stove has an external diameter of Ø100 mm.
In hot areas the duct should be insulated with 30 mm mineral wool
covered with a moisture inhibitor (aluminium tape).
It is important that the lead-in between the pipe and the wall (or floor) is
sealed using jointing compound.
A 1 m length of condensation insulated ducting for combustion air is
available as an accessory.
268
82
Air inlet Ø100
243
105 Air inlet Ø100
SUPPLY AIR/ACCESSORY

GB
43
Installation distance to walls and ceiling
1620
Min 2380
2305
475 450
1050
Combustible roof
265
120
1375
(1210)
1170
620
1880 ±60
Utv. Ø 200
400*
265
925
*If the wood compartment is to be placed between the surround and the wall at least 465 / 610 mm is required.
C11
The dimension diagrams only show the minimum
permitted installation distances for the insert. When
connecting to a steel flue, also note the safety distance
requirements of the flue. The safety distance between an
uninsulated flue and a combustible part of the building
should be at least 300 mm. The minimum distance to
combustible parts of the building or interior decoration in
front of the insert must be at least 1.5 m.
Important!
INSTALLATION DISTANCES

GB
44
Installation distance to walls and ceiling
*If the wood compartment is to be placed between the surround and the wall at least 465 / 610 mm is required.
C21
1755
2305
Min 2380
475 670
950
Combustible roof
265
120
1595
1965 ±20
(1430)
620
1390
Utv. Ø 200
400*
265
875
The dimension diagrams only show the minimum
permitted installation distances for the insert. When
connecting to a steel flue, also note the safety distance
requirements of the flue. The safety distance between an
uninsulated flue and a combustible part of the building
should be at least 300 mm. The minimum distance to
combustible parts of the building or interior decoration in
front of the insert must be at least 1.5 m.
Important!
INSTALLATION DISTANCES

GB
45
Selection of chimney connection and material in the wall behind mean that different requirements are made of installation.
Note that a non-flammable wall or firewall must meet the requirements stated on page 41. In other cases the accompanying protective screen must
be used.
Installation alternatives
Non-flammable wall / Firewall
If the wall behind is non-flammable or protected by a firewall the surround can be installed directly against it. The small, 100x15 mm, air
intakes in the protective screen on the surround sides can be filled if so desired.
Top and rear connection can be made without any extra insulation or screening of connection pipes.
Protective screen
When the surround is installed together with the integrated protective screen it is important that the airflow is not blocked.
For top connection, the gap between the top of the surround and the chimney insulation must be covered by a cuff to shield the radiant heat
from the start pipe. It is also possible to connect to the rear through the protective screen, on the condition that a fully insulated chimney is
used and the necessary safety distances observed. Ensure that there is a seal between the chimney and the protective screen.
Standard surround
CHIMNEY

GB
46
Non-flammable wall / Firewall
When the height extension section is installed in the integrated protective screen, the air outlet at the top of the surround nearest to the wall must
be sealed and the whole top surface insulated. It is also possible to connect the chimney with a backward angle through the height extension section
that requires a seal above the angle.
Protective screen
When the height extension section is installed the protective screen must be extended with a heat deflector through the height extension
section. Ensure that the heat deflector is also ventilated. The top of the surround is also insulated using the insulation sheet provided.
Raised surround
CHIMNEY

GB
47
Installation instructions surround C11, C21
Position the base plate against the wall.
Ensure that it is level, add steel shims to the
thickest sections of the base plate if possible. If the
accompanying protective screen is to be installed,
install it now. See the separate instructions.
Installation of the surround is the same for Contura 11
respectively 21. Contura 11 is illustrated.
The type plate must be positioned under the
bottom insulation of the ash-pan.
ASSEMBLY

GB
48
Lift the insert on to the base plate and adjust the feet so that the
distance from the floor to the underside of the shelf is 469 mm.
Check that it is straight and stable.
430 mm
40 mm
If the insert is to be rear connected,
connect it now.
ASSEMBLY

GB
49
Loosen the screws holding the side panels and
remove them. Use the same screws and screw holes
to instead screw the hatch frame into place. Check
that the bottom corners line up with the shelf.
Hatch frame
Shelf
ASSEMBLY

GB
50
Install the heat deflectors on the sides of the insert.
Use the six installation screws supplied in the screw
bag, and the screws that are already in the upper
corner of the insert.
Apply a bead of silicone on the base plate and then
lift in the lower section sides.
ASSEMBLY

GB
51
90°
Control measurements
When both the sides are in position the safety rail
is hung from the side washers to prevent them
falling out to the sides.
Check measure that the distance between the
sides is the same at the front edge as at the rear
edge and check that the sides are straight. Draw a
horizontal check line on the wall to simplify further
installation. Also check that the front edge of the
hatch surround aligns with the inner edge of the
concrete edges.
Applies to C 11C and
C 21C (Concrete)
Applies to C 11A, C 11S, C 21A,
C21S (Sheet metal)
ca 33 mm
80 mm
80 mm
ASSEMBLY

GB
52
The panel variants’ front are adjusted
for height using two adjustment screws
In the event of removal and height
adjustment, use the following hook
and pull out the lower door.
ASSEMBLY

GB
53
Continue with the second section’s sides and
bond them with silicone.
3 mm
3 mm
3 mm
Check that the second section is straight and
that there is an even gap of approximately 3
mm between the frame and the concrete. If
necessary, remove the lower front and adjust
the insert.
ASSEMBLY

GB
54
Apply a bead of silicone on the upper edge of the second
section and then lift in the third section sides. Support the
first side using a piece of tape so that it does not fall while
the other side is installed.
Control measurements
Control measurements
Hang the safety rail between the third section sides and
ensure that they are straight. Check that the width is the
same as section 1 at the front and rear edges.
ASSEMBLY

GB
55
Apply silicone beads along the front edge of the
sides and bond the upper front.
When top connecting through the top sheet of concrete
the knock out in the top disc must be knocked out with a
hammer. Secure the top with a few blobs of silicone and
press it forward so that it is tight to the front panel.
Bond the lower front with silicone. Use the
supplied installation angle to keep the front
panel in position while the silicone cures.
ASSEMBLY

GB
56
10
10
VANADIUM
No. 7
CHROME
On aluminium and steel fronts there are adjustment screws that
can be used to adjust the front panel by height. When the front
panel is set the outer Torx screws are screwed until they support
against the concrete. The top rests on the turned down angles at
the rear edge, these can be adjusted to get the top to the level of
the concrete.
When installing the height extension section:
• with an integrated protective screen, go to page 58.
• in combination with a non-flammable wall and
chimney connection straight backwards, go to page 62.
• in combination with a non-flammable wall and
chimney connection angled backwards through the
height extension section, go to page 65.
For installations without height extensions, top
connection to stainless steel flues is now possible;
follow the chimney manufacturer’s instructions.
Then continue on page 57 with joining and painting.
Final inspection of the installation
Before the stove is used, it must be inspected by an authorised chimney sweep. Read the “Instructions for
Lighting the CI 10 / CI 20 series” before lighting the fire for the first time.
ASSEMBLY