convenience concepts BIG SUR HIGH BOY User manual

806607 0CH
Item No. 806607 0
[email protected]
CC0031
. Broken or Missing Parts?
. Need help with Assembly?
If you have any questions just call 1-800-468-6447 or email us at
BIG SUR HIGH BOY TV STAND
42" Maximum Flat Panel Television
100 lb. Maximum Capacity
Please do not return to the store

CODE NAME FIGURE Q'TY CODE NAME FIGURE Q'TY
MALEN WRENCH 1PC
K COLOR STICK 1PC
L WOOD GLUE 1PC
1PC
HKNOB SCREW
(Φ4*20mmL)
J WIRE CAP 1PC
I SHELF SUPPORT 4PCS BACK PANEL
2PCS ADJUSTABLE
SHELF
2PCS
1PC
G KNOB 2PCS DOOR
BOTTOM PANEL 1PCF DOOR HINGE 4PCS
MIDDLE PANEL 1PCE MEDIUM SCREW
(Φ7*16mmL) 16PCS
FRONT
CROSSBAR 1PCD SMALL SCREW
(Φ7*14mmL) 24PCS
RIGHT SIDE
PANEL 1PC
BCAM LOCK
(Φ15*9mmL)
CCAM BOLT
(Φ6.5*35mmL) 14PCS
1PC
HARDWARE LIST PARTS LIST
AWOOD DOWEL
(Φ8X30mmL) 14PCS TOP PANEL 1PC
14PCS LEFT SIDE
PANEL
1
2
3
4
5
6
7
8
9

HARDWARE A x 5
NEEDED B x 5
C x 5
1.) Assemble unit laying on its side, on a soft surface.
2.) Attach Bottom Panel ( 6 ) and Middle Panel ( 5 ) t
o
Right Side Panel ( 3 ) using Wood Dowels ( A ), Cam Bolts
( C ), and Cam Locks ( B ) as shown.
** Refer to Camlock Assembly Below**
3.) Attach Front Cross Bar ( 4 ) to Right Side Panel ( 3 ) using
care not to bend.
HARDWARE A x 5
NEEDED B x 5
C x 5
1.) Attach Left Side Panel ( 2 ) to Assembly using Wood Dowels ( A ),
Cam Bolts ( C ), and Cam Locks ( B ) as shown.
**** Assembling the unit with cam and wood dowels.
STEP 1
C
A
STEP 2
A
B
Gently screw cam
dowel into the
threaded anchor.
Lightly glue one end of the
wood dowel and tap halfway
into hole. Add 2nd drop of
glue to top of dowel.
Connect to second panel
by inserting dowels into
holes.
Insert cam lock with
arrow pointing down.
Screw the cam firmly
into locked position.
C
D
5
4
3
6
B
A
C
B
B
B
CA
A
C
A
C
B
B
B
B
B
B
A
A
A
A
A
C
C
C
C
C
2

HARDWARE A x 4
NEEDED B x 4
C x 4
1.) Place unit upright and attach
Top Panel ( 1 ) using Wood
Dowels ( A ), Cam Bolts ( C ),
and Cam Locks ( B ) as shown.
HARDWARE E x 8
NEEDED F x 4
1.) Attach Door Hinges ( F ) to Doors ( 7 ) using
Medium Screws ( E ). Use care not to over tighten.
STEP 3
B
B
B
B
C
C
CAA
AA
STEP 4
EE
EE
F
F
1
7

HARDWARE E x 8
NEEDED G x 2
H x 2
1.) Attach Doors ( 7 ) to unit using
Medium Screws ( E ).
2.) Attach Knobs ( G ) to Doors
using Knob Screws ( H ).
**After Final Assembly, Adjust Hinge Screws
for Better Alignment *
*
HARDWARE J x 1
NEEDED
1.) Carefully pull apart Wire Cap ( J ) into Two pieces if needed.
2.) Align each half of the Wire Cap with pre-cut openings in both sides of
Back Panel ( 9 ). Firmly push together until snapped into place.
HARDWARE D x 24
NEEDED
1.) Attach Back Panel ( 9 ) to unit by
using Small Screws ( D ).
J
STEP 6
STEP 7
STEP 5
J
D
E
E
E
HG
E
9

HARDWARE I x 4
NEEDED
1.) Insert Shelf Supports ( I ) into desired
position holes in side panels.
2.) On a slight angle, carefully slide Adjustable
Shelf ( 8 ) into unit and on top of Shel
f
Supports ( I ).
Enjoy your new piece of Quality Furniture!
STEP 8
8
I
I