JWA SMITHERS 69376 User manual

Imported by JWA FurniturePty Ltd, Qld, Brisbane Australia.
For anyassistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
69376
3 Tier Shoe Rack
SMITHERS
ITEM CODE
800MM
250MM
1080MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all requiredcontents for complete assembly
4.Always read the assembly instrucons carefully before beginningassembly.
5.Keep all hardware partsand packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addionaltools required
2

PARTS LIST
3
1
2
3
4
5
6
7
8
910
11 12
13
14 15
15
X2

4
NO. ITEM QTY NO. ITEM QTY
A16PCS
B16PCS
C22PCS
D6PCS
E16PCS
F12PCS
4PCS
I
2PCS
K
L
4PCS
M
6PCS
N
4PCSJ
2PCS
G
H
4PCS
1PC
O2PCS
NO. ITEM QTY NO. ITEM QTY
1RIGHT SIDE PANEL 1 PC
3
1 PC
1 PC
41 PC
51 PC
61 PC
71 PC
1 PC
1 PC
1 PC
Φ6*35
Φ15*10
Φ3*12
Φ6*30
Φ4*30
Φ3.5*12
LEFT SIDE PANEL
TOP CROSS BAR(BACK)
MIDDLE CROSS BAR(BACK)
BOTTOM PANEL
TOP PANEL
BACK PANEL
8DRAWER LEFT HAND SIDE PANEL 1 PC
DRAWER BACK
DRAWER RIGHT HAND SIDE PANEL
DRAWER BOTTOM
DRAWER FRONT 1 PC
9
DOOR PANEL 2 PCE
CROSS BAR 2 PCE
SHELF 4 PCE
PARTS LIST
2
Φ4*16
10
13
11
12
14
15

STEP 1:
STEP 2:
5
J X4
I X4A X6
1
A2
AA
AA
AI
I
II
I
A
J
J
J
J
N X4
L X2K X2
E X8 X2
F X12
FF
F
F
F
F
E
E
E
E
K
L
N
N
N
N
13
13
13
14
15

STEP 3:
STEP 4:
6
D X3
B X3
B
2
B
BBD
D
D
3
45
D X3
B X3
B
BB
B
D
DD
2
1
3
5
4
Ensure the cam lock is lined up with the cam bolt when fixing.
Ensure the cam lock is lined up with the cam bolt when fixing.

STEP 5:
STEP 6:
7
B
6
H X1
B X6
A X6
Ensure the cam lock is lined up with the cam bolt when fixing.
6
2
1
5
4
B
B
A
A
AA
A
AH
H
C X22
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
CC
C
C
7

STEP 7:
STEP 8:
8
G X4
M X4
MM
M
M
MG
GG
GG
E X4
E
E
E
E
E
15
15

STEP 9:
STEP 10:
9
N X2
E X4
B X4
A X4
E
12
A
A
A
A
B
B
B
B
E
E
E
NN
N
N
12
8
8
9
910
10
11
Ensure the cam lock is lined up with the cam bolt when fixing.
A
B
H X1
WALL H
H

STEP 11:
10
ASSEMBLY IS COMPLETE
O X2
O
O

11
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1WALL FIXING X1 Expanded plastic pipe X1
HARDWARE

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
12