MuxLab Broadcast 500734 User manual

94-000843-A
SE-000843-A
6G-SDI EXTENDER OVER FIBER
500734
500734-SM10
500734-SM40
500734-SM80
Installation & Operation Manual

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 2
Copyright Notice:
Copyright © 2016 MuxLab Inc. All rights reserved.
Printed in Canada. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording or
otherwise without prior written permission of the author.
Trademarks:
MuxLab Broadcast is a registered trademark of MuxLab Inc.

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 3
Table of Contents
1. Overview.........................................................................4
1.1. Description..............................................................4
1.2. Features...................................................................7
2. Technical Specifications ................................................9
3. Installation Procedure.................................................11
3.1. Parts List ...............................................................11
3.2. Product Overview .................................................12
3.3. Physical Installation..............................................14
3.4. Installation & Power-up Procedure.......................18
3.5. Supported Video Modes........................................20
3.6. SDI Input Connections..........................................21
3.7. SDI Output Connections.......................................21
4. Firmware Upgrade Procedure....................................22
4.1. Firmware Upgrade Procedure ...............................22
4.2. USB Driver Setup .................................................25
5. Unit Control and Status...............................................28
6. Troubleshooting ...........................................................29
7. Appendix.......................................................................31
A. ASCII Command Set.............................................31
8. Product Warranty Policy............................................37

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 4
1.
Overview
1.1.
Description
The 6G-SDI Extender over Fiber Optic with Return Channel is a
unique solution from MuxLab for extending SDI cameras or other
SDI sources up to 4K resolutions at 30Hz to a distance of up to
1300ft (400m) using OM4 multi-mode fiber (model 500734),
33,000ft (10km) using single-mode fiber (model 500734-SM10),
132,000ft (40km) using single-mode fiber (model 500734-SM40),
and 264,000ft (80km) using single-mode fiber (model 500734-
SM80).
The product supports multichannel transmission, and can
simultaneously transmit up to 9Gbps of data throughput over the
fiber link, and allows for versatile combinations of sources,
including 6G-SDI, 3G-SDI and HD-SDI. The unit supports
simultaneous transmission of mixed signals such as one 6G-SDI
signal + one 3G-SDI, or three 3G-SDI signals, or two 3G-SDI
signals + two HD-SDI signals, and many other combinations up to
9Gbps. The device supports one input and one output SDI port,
plus three directional SDI ports that can be individually configured
as input or output, or set to automatic direction detection. This
flexibility allows for up to four source ports and one return
channel, or up to one source port and four return channels, or
anything in between. The SDI return channel may be used for AV
monitoring and talk-back, while the RS232 pass-through supports
return of tally light, camera control unit (CCU) and control of end
devices.

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 5
Figure 1 System Connectivity Overview

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 6
Typical Applications:
•Video (cinema) production
•Studio broadcasting production
•Studio to Studio
•Mobile video (broadcasting vehicle)
•News coverage and live events
•Post production

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 7
1.2.
Features
•Up to 1300ft (400m) via multimode OM4 fiber and
up to 264,000ft (80km) via singlemode fiber.
•Supports multichannel transmission, and can
simultaneously transmit up to 9Gbps of data traffic
on the fiber link.
•Accepts mixed signal transmission of up to one 6G-
SDI signal + one 3G-SDI signal, three 3G-SDI
signals, or two 3G-SDI signals + two HD-SDI
signals, and many other combinations up to 9Gbps,
and in any direction, including the return channels.
•Supports one input and one output SDI port, plus
three configurable directional SDI ports that can be
individually configured as input or output, or set to
automation direction detection.
•Supports up to four source ports and one return
channel, or up to one source port and four return
channels, or any combination in between. The SDI
return channel may be used for AV monitoring and
talk-back.
•Supports RS232 pass-through for remote control,
and as a return channel for tally light and for a
camera control unit (CCU).
•Maximum resolution supported: 4096x2160 @
24/25Hz, 3840x2160 @ 30Hz.
•Supported SMPTE Standards: SMPTE-292M, SMPTE-
296M, SMPTE-372M, SMPTE-424M, SMPTE-425M.

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 8
•Supports all 6G channel configurations (1, 2 or 4
BNC).
•Automatic SDI Link recognition and configuration.
•USB interface may be used for setting the three
directional SDI ports to a fixed direction, or to set
them to automatic direction detection mode. The
USB port is also used for diagnostics, and
upgrading the unit firmware.
•Supports a standard 10G SFP+ module for the
optical fiber interface.
•Supports an aluminum casting enclosure for
ruggedized use.
•Multiple ¼”-20 threads for Camera mounting or
equipment attachment.

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 9
2.
Technical Specifications
Specifications
Environment
HD/3G/6G-SDI Digital Signal Transmission
Enclosures
Measurements
Tx: 110mm (4.3”) x 110mm (4.3”) x 32mm (1.25”)
Rx: 110mm (4.3”) x 110mm (4.3”) x 32mm (1.25”)
Color
Black
Control
Serial Terminal Emulation with USB Interface
Distance
•Model 500734: Up to 985ft (300m) via OM3
multimode fiber and 1300ft (400m) via OM4
multimode fiber.
•Model 500734-SM10: Up to 33,000ft (10km) via
singlemode fiber.
•Model 500734-SM40: Up to 132,000ft (40km) via
singlemode fiber. Requires a 5dB attenuator for
distances less than 33,000ft (10km).
•Model 500734-SM80: Up to 264,000ft (80km) via
singlemode fiber. Requires a 10dB attenuator for
distances less than 115,500ft (35km).
Compliance
FCC, CE, RoHS
Power
12VDC, 1.25Amp
External Power Supply with US, UK & Euro blades
Temperature
Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Table 1 Specifications

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 10
Transmitter Connectivity
Front Side
1x BNC SDI Input Connector (0.8V pp, 75 ohms)
1x BNC SDI Output Connector (0.8V pp, 75 ohms)
3x BNC SDI Directional Connectors (0.8V pp, 75 ohms)
Rear Side
1x SFP+ Module Connector
1x Terminal Block for RS232 Interface
Lower Side
1x Power Connector (12VDC, 1.25Amp)
Top Face
1x Mini USB for Firmware Updates, plus Control & Status
Table 2 Transmitter Connectivity
Receiver Connectivity
Front Side
1x BNC SDI Input Connector (0.8V pp, 75 ohms)
1x BNC SDI Output Connector (0.8V pp, 75 ohms)
3x BNC SDI Directional Connectors (0.8V pp, 75 ohms)
Rear Side
1x SFP+ Module Connector
1x Terminal Block for RS232 Interface
Lower Side
1x Power Connector (12VDC, 1.25Amp)
Top Face
1x Mini USB for Firmware Updates, plus Control & Status
Table 3 Receiver Connectivity

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 11
3.
Installation Procedure
3.1.
Parts List
The 6G-SDI Extender over FIBER Kit with Return
Channel (500734, 500734-SM10, 500734-SM40 &
500734-SM80) come with the following parts:
•1x Transmitter Unit (Tx)
•1x Receiver Unit (Rx)
•2x 12VDC Wall-mount Power Supply
•US, UK & Euro Blades for the Wall-mount Power
Supply
•2x 10G SFP+ modules with LC connectors

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 12
3.2.
Product Overview
3.2.1.
Transmitter
The external connections and light indicators of the
transmitter unit are detailed in Figure 2. Please
familiarize yourself with them before installing the unit.
LED Indicator
When SDI Link
is established
Power
LED Indicator
Mini-USB Port
Firmware
Upgrade
& Unit Control
Flashing LED
Indicator
When
information
Is passing
through the
link
SFP+ module
Figure 2 Front View of Transmitter
POWER
connector
SERIAL port
6G/3G/HD-SDI Input
6G/3G/HD-SDI Output
3G/HD-SDI In / Out
3G/HD-SDI In / Out
3G/HD-SDI In / Out

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 13
3.2.2.
Receiver
The external connections and light indicators of the
receiver unit are detailed in Figure 3. Please familiarize
yourself with them before installing the unit.
LED Indicator
When SDI Link
is established
Power
LED Indicator
Mini-USB Port
Firmware Upgrade
& Unit Control
Flashing LED
Indicator
When
information
Is passing
through the
link
SFP+ module
6G/3G/HD-SDI Output
3G/HD-SDI In / Out
Figure 3 Front View of Receiver
POWER
connector
SERIAL port
3G/HD-SDI In / Out
3G/HD-SDI In / Out
6G/3G/HD-SDI Input

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 14
3.3.
Physical Installation
Port A Input, see table 4
Port A Output, see table 4
Port C In/Out, see table 4
SOURCE INPUT (Camera, Etc)
Must use 6G/3G/HD 75Ω graded coax cable
In accordance with the SDI Throughput needed.
Port D In/Out, see table 4
Important: Always Use SDI A, then B, etc… as first
connections for any SDI transmission speed, see table 4.
Connection to FIBER
(Duplex Connection)
Connection to FIBER
(Duplex Connection)
Important: Keep the Receiver outputs and signals in the
same order and speed as the Transmitter, see table 4.
DESTINATION OUTPUT (Recorder, Monitor, Ect.)
Must use 6G/3G/HD 75Ω graded coax cable
In accordance with the SDI Throughput needed.
12VDC Power Input
Duplex Connection:
Port B In/Out, see table 4
Port A Input, see table 4
Port A Output, see table 4
Port B In/Out, see table 4
Port C In/Out, see table 4
Port D In/Out, see table 4
12VDC Power Input
Figure 4 Physical Installation

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 15
Figure 5 Input / Output Combinations
Figure 5 highlights one example of the port direction combinations
that are possible, but other combinations are also possible.
Table 4 below shows the combination of signals that can be
transmitted/received over the fiber link, based on the Figure 5
example, and based on the number of ports used for
transmission/reception in a given direction. The total bandwidth
available is 9Gbps, so varying combinations of
transmission/reception rates totaling 9Gbps are possible.
Case
Port A
Signal
1
6G-SDI
2
3G-SDI
3
HD-SDI
Table 4a For 1 port used (Port A)

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 16
Case
Port A
Signal
Port B
Signal
1
6G-SDI
3G-SDI
2
6G-SDI
HD-SDI
3
3G-SDI
3G-SDI
4
3G-SDI
HD-SDI
5
HD-SDI
HD-SDI
Table 4b For 2 ports used (Ports A & B)
Case
Port A
Signal
Port B
Signal
Port C
Signal
1
6G-SDI
HD-SDI
HD-SDI
2
3G-SDI
3G-SDI
3G-SDI
3
3G-SDI
3G-SDI
HD-SDI
4
3G-SDI
HD-SDI
HD-SDI
5
HD-SDI
HD-SDI
HD-SDI
Table 4c For 3 ports used (Ports A, B & C)
Case
Port A
Signal
Port B
Signal
Port C
Signal
Port D
Signal
1
3G-SDI
3G-SDI
HD-SDI
HD-SDI
2
3G-SDI
HD-SDI
HD-SDI
HD-SDI
3
HD-SDI
HD-SDI
HD-SDI
HD-SDI
Table 4d For 4 ports used (Ports A, B, C & D)

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 17
Simplex Connection:
If transmission is only required in one direction, this device can be
connected with a single fiber in a simplex arrangement as indicated
in the following steps.
1. While looking at the unit from the top, connect the single
fiber cable to the Transmitter right most LC connector as
shown below.
2. While looking at the unit from the top, connect the opposite
end of the fiber cable to the Receiver left most LC
connector as shown below.
Figure 6 Connecting the Fiber Cable
3. The unused LC connector on both the Transmitter and
Receiver must be protected from dust. This can easily be
accomplished by cutting the protective rubber plug in half
and inserting the plug into the unused LC connectors.
Figure 7 Plug Unused Fiber Port
Important note: The serial port is not available when only using a
single fiber cable in a simplex arrangement.

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 18
3.4.
Installation & Power-up Procedure
In order to install the product, please follow the steps
below:
1. First, install the Transmitter near the SDI signal
source equipment and Return Channel sink
(destination) equipment. Attach the unit via the
mounting holes or by other appropriate means.
2. Transmitter: Follow the procedure in section 5 (Unit
Control and Status) to individually configure Ports
B, C & D of the Transmitter as either Inputs,
Outputs, or as Auto-detect (to automatically detect
the transmission direction). Note that Auto-detect is
the default setting.
3. Install the Receiver near the SDI signal sink
(destination) equipment and Return Channel source
equipment. Attach the unit via the mounting holes or
by other appropriate means.
4. Receiver: Follow the procedure in section 5 (Unit
Control and Status) to individually configure Ports
B, C & D of the Receiver as either Inputs, Outputs,
or as Auto-detect (to automatically detect the
transmission direction). Note that Auto-detect is the
default setting. Make sure that a given Transmitter
Port set as an Input is set as an Output on the
Receiver, and vice versa.
5. Connect the necessary number of SDI Compatible
75Ω Coax cables in order to carry the video/audio
signal. Connect the source equipment to the
Transmitter ports configured as SDI Inputs, and
connect the Return Channel sink (destination)
equipment to the Transmitter ports configured as

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 19
SDI Outputs. Always start by connecting the first
cable to the BNC A, then B and so on.
6. Once the Transmitter is installed and connected with
the SDI coax cables, then connect and run the fiber
optic cable from the Transmitter to the Receiver unit,
using either multimode or singlemode fiber
depending on the 6G-SDI Extender model being
installed. Respect the distance specification listed on
Table 1.
7. After hooking up the fiber optic cable to the SFP+
port on the Receiver, proceed to connect the SDI
coax cables from the Receiver to the destination
device (e.g.: Recorder, Monitor, Mixer, Capture
card, etc.). Connect the sink (destination) equipment
to the Receiver ports configured as SDI Outputs, and
connect the Return Channel source equipment to the
Transmitter ports configured as SDI Inputs.
8. Once all the cabling is installed, next plug the
12VDC wall-mount power supplies to both the
Transmitter and Receiver.
9. Each unit will power up and auto-initialize.
10. Next the fiber link will sync, and the link indicator
on each unit will blink after the negotiation process
has successfully completed.
11. If the source is generating a video signal at the
Transmitter end, then the Receiver will output the
same signal which can be terminated on a Recorder,
Monitor, Mixer, Capture card, etc.

© MuxLab Inc. 6G-SDI Extender Over FIBER
Page 20
3.5.
Supported Video Modes
Resolution 10Bit 4:2:0 12Bit 4:2:0
10Bit 4:2:2 12Bit 4:2:2
12Bit 4:4:4
10Bit 4:4:4:4
2160p @ 30/29.97Hz
2160p @ 25Hz
2160p @ 24/23.98Hz
6Gbit/s
Single Link 6G
Dual Link 3G
1080p @ 60/59.94Hz
1080p @ 50Hz
3Gbit/s
Single Link 3G
Dual link 1.5G (HD)
6Gbits/s
Single Link 6G
Dual Link 3G
1080i @ 60/59.94Hz
1080i @ 50Hz
1080p @ 30/29.97Hz
1080p @ 25Hz
1080p @ 24/23.98Hz
1.5Gbit/s
Single Link 1.5G
(HD)
3Gbit/s
Single Link 3G
Dual Link 1.5G (HD)
720p @ 60/59.94Hz
720p @ 50Hz
720p @ 30/29.97Hz
720p @ 25Hz
720p @ 24/23.98Hz
1.5Gbit/s
Single Link 1.5G
(HD)
3Gbit/s
Single Link 3G
3D: 1080p @ 60/59.94Hz
3D: 1080p @ 50Hz
6Gbit/s
Single Link 6G
Dual Link 3G
3D: 1080i @ 60/59.94Hz
3D: 1080i @ 50Hz
3D: 1080p @ 30/29.97Hz
3D: 1080p @ 25Hz
3D: 1080p @ 24/23.98Hz
3Gbit/s
Single Link 3G
Dual Link 1.5G (HD)
6Gbit/s
Single Link 6G
Dual Link 3G
3D: 720p @ 60/59.94Hz
3D: 720p @ 50Hz
3D: 720p @ 30/29.97Hz
3D: 720p @ 25Hz
3D: 720p @ 24/23.98Hz
3Gbit/s
Single Link 3G
Dual Link 1.5G (HD)
6Gbit/s
Single Link 6G
Dual Link 3G
Table 4 Supported Video Mode Matrix