manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Cooper Crouse-Hinds
  6. •
  7. Light Fixture
  8. •
  9. Cooper Crouse-Hinds Champ FMV Series Setup guide

Cooper Crouse-Hinds Champ FMV Series Setup guide

Champ®LED Floodlight
FMV Series LED Fixtures
Installation & Maintenance Information
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IF 1622
APPLICATION
Champ®LED Floodlights are suitable for use in the following hazardous (classified) locations as
defined by the National Electrical Code (NEC®):
• Class I, Division 2, Groups A, B, C, D
Refer to the floodlight nameplate for specific classification information, maximum ambient
temperature suitability and corresponding operating temperature (T-Number).
Champ®LED Floodlights construction is designed for use indoors and outdoors in marine and wet
locations, where moisture, dirt, corrosion, vibration and rough usage may be present.
WARNING
To avoid the risk of fire, explosion, or electric shock, this product should be installed,
inspected, and maintained by a qualified electrician only, in accordance with all applicable
electrical codes.
WARNING
To avoid electric shock:
Be certain electrical power is OFF before and during installation and maintenance.
Floodlight must be supplied by a wiring system suitable for Class I, Division 2 per NEC with
an equipment grounding conductor.
To avoid burning hands:
Make sure lens and lamp are cool when performing maintenance.
To avoid explosion:
Make sure the supply voltage is the same as the floodlight voltage.
Do not install where the marked operating temperatures exceed the ignition temperature of the
hazardous atmosphere.
Do not operate in ambient temperatures above those indicated on the floodlight nameplate.
Use only replacement parts from Cooper Crouse-Hinds.
Use proper supply wiring as specified on the floodlight nameplate.
All gasket seals must be clean.
Before opening, electrical power to the floodlight must be turned off. Keep tightly closed when
in operation.
IF 1622 • 04/11 Copyright © 2011, Cooper Industries, Inc. Page 1
INSTALLATION
Mounting
WARNING
Yoke Mount - Wall Mount Using Floodlight Yoke Only
1. Using floodlight yoke as a template, mark and drill desired location on mounting surface.
2. Secure floodlight yoke to surface using ½" bolts or lag screws (not provided).
WIRING
Wiring the Floodlight
1. All components in the fixture are prewired so only line in, neutral, and ground need to be
connected in the fixture to the lead wires (or terminals) per the wiring diagrams using
methods that comply with all applicable codes. Terminate the equipment grounding
conductor (green) first, the common (white) next, and finally, the line voltage (black) last.
For DC voltage applications, connect the positive (+) lead to the white wire and the negative
(-) lead to the black wire. Tighten all electrical connections. Figure 1
LINE IN (BLK)
NEUTRAL (WHT)
V+ (RED)
V- (BLK)
INPUT OUTPUT
DRIVER
INPUT
NEUTRAL (WHT)
LINE IN (BLK)
OUTPUT
V- (BLK)
V+ (RED)
DRIVER
INPUT
NEUTRAL (WHT)
LINE IN (BLK)
OUTPUT
V- (BLK)
V+ (RED)
DRIVER
INPUT
NEUTRAL (WHT)
LINE IN (BLK)
OUTPUT
V- (BLK)
V+ (RED)
DRIVER
LED SUBARRAY
LED SUBARRAY
LED SUBARRAY
LED SUBARRAY
LED ARRAY
TRANSFORMER
347V OR 480V (BLU OR RED)
NEUTRAL (WHT)
LINE OUT (BLK)
NEUTRAL (WHT)
347V OR 480V 60HZ INPUT
VMV11L
137W VERSION (OTHER VERSION WIRING WILL VARY*)
LINE IN (BLK)
NEUTRAL (WHT)
INPUT
LINE IN (BLK)
NEUTRAL (WHT)
INPUT
LINE IN (BLK)
NEUTRAL (WHT)
INPUT
INPUT
NEUTRAL (WHT)
LINE IN (BLK)
100V TO 277V (BLK)
NEUTRAL (WHT)
100V TO 277V 50 OR 60HZ INPUT OR 108TO 150VDC INPUT
VMV11L
LED ARRAY
V+ (RED)
V- (BLK)
OUTPUT
V+ (RED)
V- (BLK)
OUTPUT
V- (BLK)
DRIVER
DRIVER
LED SUBARRAY
LED SUBARRAY
V+ (RED)
OUTPUT
OUTPUT
V- (BLK)
V+ (RED)
DRIVER
DRIVER
LED SUBARRAY
LED SUBARRAY
*NOTES:
5L VERSION WILL HAVE TWO (2) DRIVERS AND FOUR (4) LED'S
7L VERSION WILL HAVE TWO (2) DRIVERS AND SIX (6) LED'S
9L VERSION WILL HAVE THREE (3) DRIVERS AND EIGHT (8) LED'S
FOR DC WIRING, ATTACH POSITIVE (+) LEAD TO LINE OUT (BLK) AND ATTACH NEGATIVE (-) LEAD TO
NEUTRAL (WHT ) WIRE
GROUND (GRN)
GROUND (GRN)
Figure 2 - Wiring Diagram
Champ®LED Floodlights are supplied for use with a choice of voltages:
• 100VAC - 277VAC, 50/60Hz, 108-150VDC
• 347VAC 60Hz
• 480VAC 60Hz
• NEMA 4X • UL IP66
WARNING
To avoid ignition of the hazardous atmospheres or overheating of the floodlight:
Do not position the floodlight beyond the aiming range limits.
2. Re-install the back panel and tighten all eight (8) panel mounting screws to 80 in.-lbs.
Figure 3
3. To make final vertical adjustment, loosen the pivot bolts on the floodlight yoke to position
floodlight at the desired angle (limited to 60 degrees forward and 45 degrees back).
Tighten the two pivot bolts to 45 ft.-lbs.
4. Rotate the floodlight housing to the desired position.
5. Turn power on.
Loosen bolts to
set floodlight
angle
MAINTENANCE
• Perform visual, electrical, and mechanical inspections on a regular basis. The environment
and frequency of use should determine this. However, it is recommended that checks be
made at least once a year. We recommend an Electrical Preventive Maintenance Program as
described in the National Fire Protection Association Bulletin NFPA 70B: Recommended
Practice for Electrical Equipment Maintenance (www.nfpa.org).
• The lens should be cleaned periodically to ensure continued lighting performance. To clean,
wipe the lens with a clean damp cloth. If this is not sufficient, use a mild soap or a liquid
cleaner such as Collinite NCF or Duco #7. Do not use an abrasive, strong alkaline, or acid
cleaner. Damage may result.
• Visually check for undue heating evidenced by discoloration of wires or other components,
damaged parts, or leakage evidenced by water or corrosion in the interior. Replace all worn,
damaged, or malfunctioning components and clean gasket seals before putting the luminaire
back into service.
• Electrically check to make sure that all connections are clean and tight.
• Mechanically check that all parts are properly assembled.
REPLACEMENT PARTS
Cooper Crouse-Hinds Champ®LED Floodlights are designed to provide years of reliable lighting
performance. However, should the need for replacement parts arise, they are available through your
authorized Cooper Crouse-Hinds distributor. Assistance may also be obtained through your local
Cooper Crouse-Hinds representative or the Cooper Crouse-Hinds Sales Service Department, P.O. Box
4999, Syracuse, New York 13221, Phone 866-764-5454.
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable.
The accuracy or completeness thereof are not guaranteed. In accordance with Cooper Crouse-Hinds "Terms and Conditions of Sale," and
since conditions of use are outside our control, the purchaser should determine the suitability of the product for his intended use and
assumes all risk and liability whatsoever in connection therewith.
IF 1622
Cooper Crouse-Hinds, LLC Revision 1
PO Box 4999, Syracuse, New York 13221 • U.S.A. New 04/11
Copyright© 2011, Cooper Industries, Inc.
DIMENSIONS
21.0
532.9
16.0
405.9
6.6
167.1
21.75
552.5
4.75
120.7
Ø .55
14

Other Cooper Crouse-Hinds Light Fixture manuals

Cooper Crouse-Hinds EVI Series Setup guide

Cooper Crouse-Hinds

Cooper Crouse-Hinds EVI Series Setup guide

Cooper Crouse-Hinds ELPS LIGHT-PAK ELPS-K50 Setup guide

Cooper Crouse-Hinds

Cooper Crouse-Hinds ELPS LIGHT-PAK ELPS-K50 Setup guide

Popular Light Fixture manuals by other brands

Triarch 31064 Assembly instructions

Triarch

Triarch 31064 Assembly instructions

Lightolier Lytecaster 604MR specification

Lightolier

Lightolier Lytecaster 604MR specification

Mr. Christmas Another Original 36451 Instruction booklet

Mr. Christmas

Mr. Christmas Another Original 36451 Instruction booklet

Worldsemi WS2812 user manual

Worldsemi

Worldsemi WS2812 user manual

Yongnuo YN508 user manual

Yongnuo

Yongnuo YN508 user manual

EuroLite LED SLS-503 TCL user manual

EuroLite

EuroLite LED SLS-503 TCL user manual

Lightolier IS_CD7-Surface Assembly and installation

Lightolier

Lightolier IS_CD7-Surface Assembly and installation

Anslut 420-119 User instructions

Anslut

Anslut 420-119 User instructions

Philips 6913087PH Instruction leaflet

Philips

Philips 6913087PH Instruction leaflet

Chauvet LED-BANK4 operating instructions

Chauvet

Chauvet LED-BANK4 operating instructions

Eurotops X-ARC TOUCH quick start guide

Eurotops

Eurotops X-ARC TOUCH quick start guide

CLF ARES user manual

CLF

CLF ARES user manual

Chauvet Professional Maverick Storm 3 Beamwash Quick reference guide

Chauvet Professional

Chauvet Professional Maverick Storm 3 Beamwash Quick reference guide

Lightolier Lytecaster 1100DAICM specification

Lightolier

Lightolier Lytecaster 1100DAICM specification

Beamz 153.329 instruction manual

Beamz

Beamz 153.329 instruction manual

vonado 42115 manual

vonado

vonado 42115 manual

Emos ZM5222 manual

Emos

Emos ZM5222 manual

Philips 69112-32-PH Specification sheet

Philips

Philips 69112-32-PH Specification sheet

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.