Cooper Lighting Corelite Jaylum Suspended T5 User manual

INSTALLATION
Suspended T5/T8 Luminaire
1
21
1
2
3
4
2
Insert Barrel Terminal
into keyhole slot.
1Slide Cable Coupler onto Main Suspension Cable
and secure Coupler to appropriate mounting point
at ceiling.
3Insert Cross Cable into Cable Gripper and install
thumbscrew.
Loosen thumbscrew to level xture. Re-tighten
as necessary once xture leveling has been
completed.
2Install Cable Gripper onto Main Suspension Cable.
4Adjust Main Cable to desired length and cut
excess cable if necessary.
! IMPORTANT: Install CABLE CRIMP prior to
cutting cable.
Fully insert Toggle into
keyhole slot.
3Install Screw(s)
CROSS CABLE INSTALLATION
CABLE/GRIPPER INSTALLATION
12” Aircraft Cable with Barrel Terminals
and Steel Toggles (included).
J-BOX
(by others)
POWER FEED
SJT CordCable
Cable Coupler
Cable
Cable Crimp
NON-POWER FEED
Please refer to Corelite“Connection at Ceiling” instructions
for detailed information on various mounting methods.
Cable Coupler
CONNECTION AT FIXTURE
SAVE THESE INSTRUCTIONS
WARNINGS
1) WARNING! – Risk of Fire/Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.
2) WARNING! – Risk of Fire/Electric Shock. If not qualifiied, consult an electrician.
3) WARNING! – Risk of Fire/Electric Shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when drilling for installation of reflector kit hardware. Check for
enclosed wiring and components.
NOTES
1) NOTE! – This product must be installed in accordance with local/ national electrical codes.
2) NOTE! – Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an
enclosure of wiring or electrical components.
3) NOTE! – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.
4) NOTE! – Disconnect all power before proceeding.
Not all options available. Please consult your Cooper Lighting Representative for availability. Specications and Dimensions subject to change without notice.
JAYLUM
ADE130026

Suspended T5/T8 Luminaire
Install rst xture with two AC cable
assemblies, then second xture with
one additional cable.
Bend out tapered aligning tabs and
t into aligner slots. (Fixture 2 is now
supported by xture 1 at the joint.)
Make electrical connections.
End Caps: Slide into end of xture
and secure with two 10-32 x 3/8”
self tapping screws.
Set in place.
*T5 Shown
END CAP
Slide-N-LockTM DUST COVER
Tuck wires into wire cavity, slide both
xtures together. Secure xtures using
two 10-32 x 3/8” screws and nuts.
Tighten 1/4 turn past hand-tight.
NOTE: Remove lm from optic before installing.
To Install - set in place over lamps.
The Slide-N-Lock comes pre-set from the factory to the customer specied optical setting.
To eld adjust the optic, depress the control notch and slide tab to desired setting (instructions
located on optic).
Break o appropriate KO, slide power cord through KO opening, then
secure power cord with strain relief.
Note: Location of the KO’s varies depending on xture
*For continuous rows see joining sheet.
*For continuous rows see joining sheet.
Not all options available. Please consult your Cooper Lighting Representative for availability. Specications and Dimensions subject to change without notice.
5/8”-7/8” KNOCK OUT
INSTALL LAMPS
JOINING
POWER DROPS / KNOCK-OUTSMOUNT SPACING
FIXTURE LENGTH
FIXTURE LENGTH
SAMPLE ROW
Power
96” SPACING 96” SPACING
INSTALLATION
JAYLUM
ADE130026
TM
TAB