Cooper Wiring Devices Aspire RF User manual

Menu Back
All ON All OFF
1
All ON
Menu Back
All OFF
2
34
56
78
910
Devices
Mon 12:00 AM
Devices
Mon 12:00 AM
Wir l ss Control Syst m
User Guide
A Step-by-Step Guide for
Planning, Installing, and
Operating a Complete Designer
Wireless Control System

2
(T IS PAGE INTENTIONALLY LEFT BLANK)

Congratulations!
3
Congratulations on your Purchas of an
Wir l ss Control Syst m!
Part of the next generation of convenient, dependable, and user-friendly wireless controls, your new system
allows you to create a wireless, two-way network within your family home, condo, or apartment. The network
puts you in command of a large number of compatible devices from a single, remote control. Some of the
benefits that you will enjoy with your new wireless control system include:
• Convenience and Versatility – use the centralized control system for home lighting controls, and appliances.
• Security – enjoy a safe arrival at night by coming home to a well-lit house by simply triggering your Z-Wave
enabled garage door opener
• Enhanced ome Experience – set the mood for entertainment, romance, or relaxation by setting all light
levels for any group of fixtures with the touch of a button
• Ease of Installation – benefit from the simple and practical set-up process with a quick and painless install
every time
• Time and Energy Savings – turn off groups of lights from any location in the home and reduce energy bills
with one-touch control

Table of Contents
Using This Guid
We recommend that you carefully review the contents of this guide to get the most from your wireless
system. Although previous verions of the User Guide are mostly valid, Version B of the User Guide is best
suited for software version 1.1.2. If you have additional questions related to the installation or the operation
of your Aspire RF Wireless Control System, please call 1-866-853-4293 or go to
cooperwiringdevices.com/AspireRF.
Safety Information and FCC Information........................................................................... 6
Introduction .......................................................................................................... 7
Important Notes ................................................................................................. 7
ow the System Works ........................................................................................ 7
Quick Reference Guide ............................................................................................. 8
Optional Accessories ............................................................................................... 10
Get Started ........................................................................................................... 11
Navigate Menu Screens ........................................................................................ 11
Create Custom Names ......................................................................................... 12
Set Current Day and Time ...................................................................................... 13
Install and Control Devices ....................................................................................... 14
Install a Device .................................................................................................. 14
Configure a Device .............................................................................................. 15
Configure Off Delay ............................................................................................. 16
Configure ALL ON and ALL OFF Group ....................................................................... 16
Configure Panic On and Off Times ............................................................................ 18
Configure Power On State ...................................................................................... 19
Configure Ramp Time .......................................................................................... 20
Non-Cooper Parameters ........................................................................................ 21
Activate Individual Devices .................................................................................... 23
Check Device Status ............................................................................................ 24
Rename a Device ............................................................................................... 25
Change a Location of a Device ............................................................................... 26
Activate ALL ON and ALL OFF ................................................................................. 27
Activate Panic Mode ............................................................................................ 28
Customize Panic Group ........................................................................................ 29
ide Devices ..................................................................................................... 29
Create and Control Scenes ........................................................................................ 31
Create a Scene .................................................................................................. 31
Activate a Scene ................................................................................................. 33
Create Favorite Scenes ......................................................................................... 34
Rename a Scene ................................................................................................ 35
Renumber a Scene .............................................................................................. 36
Delete a Scene .................................................................................................. 37
Edit a Scene ..................................................................................................... 38
Transfer a Scene to a Wall Mount Controller ................................................................ 39
ide Scenes ..................................................................................................... 40
4
Devices Scenes Events Settings Away

Table of Contents
5
Devices Scenes Events Settings Away
Create and Control Events ......................................................................................... 41
Create an Event .................................................................................................. 41
Activate or Deactivate an Event ................................................................................ 44
Activate or Deactivate All Events .............................................................................. 44
Rename an Event ............................................................................................... 45
Delete an Event .................................................................................................. 46
Edit an Event ..................................................................................................... 47
Edit and Control the Away Feature ............................................................................... 50
Edit the Away Feature ........................................................................................... 50
Activate or Deactivate the Away Feature ...................................................................... 54
ake Advanced Changes to Your System ....................................................................... 55
Create an Association Between Devices ...................................................................... 55
Replicate andheld Information to a Second Controller .................................................... 56
Select a New Primary Controller ............................................................................... 58
Uninstall a Device ............................................................................................... 59
Activate Child Lockout .......................................................................................... 60
Reset the System ................................................................................................ 61
Scan for Devices ................................................................................................ 62
Troubleshooting Guide and aintenance ....................................................................... 63
Retrieve Version Information about your System ............................................................ 63
Retrieve Version Information about Individual Devices ..................................................... 64
Retrieve Device Information (“Who Are You” feature) ....................................................... 65
Update Secondary Controller Device Information (“Get Name & Locn” feature) ......................... 65
Replace a Failed Device ........................................................................................ 66
Remove a Failed Device ........................................................................................ 67
Utilize Network Discovery ...................................................................................... 68
Ordering Information for Cooper Wiring Devices .............................................................. 69
Glossary .............................................................................................................. 71
Warranty .............................................................................................................. 73

Safety Information & FCC Information
Saf ty First
6
WARNING
• Turn OFF circuit breaker or remove fuse(s) and test that power is off before wiring.
• Never wire any electrical device with power turned on. Wiring device (switch, dimmer, receptacle)
energized may cause permanent damage to device and void warranty.
• If you are not sure about any part of these instructions, please contact a licensed electrician.
CAUTION
• Use only with 120V AC 60 z.
• Do not exceed maximum rating of the devices as indicated on the product.
• Must be installed and used in accordance with electrical codes.
• If a bare copper or green ground connection is not available in the wallbox, contact a licensed electrician
for installation.
• Use only #14 or #12 copper wire with these devices.
FCC INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1: This device may not cause harmful interference, and
2: This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. owever, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:
Any changes or modifications not expressly approved by Cooper Wiring Devices could void the user’s
authority to operate the equipment.
Cooper Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269 • 866-853-4293

Introduction
How th Syst m Works
Batteries Required
In order to power on, the tabletop controller requires AA batteries or AC adapter and the handheld controller
requires AA batteries.
Powering On and Off the Controllers
Pressing any button will activate the controllers.
Timing Out
The display backlight will turn itself off after a period of
10 seconds of inactivity. After 60 seconds of inactivity,
the controller will automatically power off. This will cause
all unsaved data to be lost.
Your ASPIRE RF devices function as both receivers, allowing you to control the loads to which they are
attached, and as repeaters, extending and improving signals throughout your home. Rather than depending
on line-of-site communications like other technologies, Aspire RF employs Z-Wave technology that creates
a “mesh” network.
The controller is a portable device capable of both managing your Z-Wave network and controlling all of
the devices on your network.
In addition to your ASPIRE RF Wireless Control System, ASPIRE offers a fully integrated array of devices and
accessories, including smart dimmers, switches, duplex receptacles, and a wealth of accessories to link
your entire network.
This product works with other Z-Wave products from different vendors and product categories as part of the
same Z-Wave network.
Controller Dimmer
switch
Switch Receptacle
Handheld controller
2 AA batteries
Tabletop controller
3 AA batteries
or AC adapter
Important Not s
7

Quick Reference Guide
8
Menu Back
ALL
ON
ALL
OFF
PP
AC adapter plug-in
OK button
Primary Controller
Callout
ALL OFF/Dim
button
Panic button
ALL ON/Brighten
button
Favorite Scene
buttons
Eight of your favorite scenes
can be accessed directly with
an easy one-touch control.
Use this button to select
settings in menus.
Indicates if it is the
primary controller.
Battery Status
Indicator
Appears when battery is low
on power. Arrow pad
Navigate through menus and
screens, create custom names,
and change various settings.
Turn all devicesin the ALL ON group on
at once. Brightens selected dimmer
switches.
Turn all devicesin the ALL OFF group off
at once. Dims selected dimmer switches.
Trigger agroup of devicesto turn off and on
in a pattern that attracts attention.
Devices
Mon 12:00 AM
Menu/Save
button
Access the main menu
and save desired settings.
Back/Cancel
button
Exit a menu screen and return
to the previous menu.
Devices enu
A device can be a dimmer switch, a regular switch, or a receptacle. Use this menu to
install and configure each device. From this menu you can also activate individual
devices, check device status, rename a device, change the location of a device, and add a
device to the ALL ON / ALL OFF group. Some advanced functions in this menu include:
Creating an association between devices, activating child lockout, and uninstallation of a
device.
Scenes enu
A scene is a combination of lighting or appliance devices selected by the user that can be
controlled as a group by the wireless system. Once you’ve installed devices into the
system, you can program your controllers to create and control up to 64 scenes in your
home. You can create a list of favorite scenes (such as Bedtime, Movie Time, or Dinner)
that can be accessed with an easy one-touch control. Use this menu to create a scene,
activate a scene, create favorite scenes, rename a scene, renumber a scene, edit a scene,
and delete a scene.
Example: For watching movies, you can create a Scene that dims the overhead
light and turns on accent lights. The scene can then be easily accessed with a
one-touch control.
M nus
Tabl top Controll r

Quick Reference Guide
Events enu
An event is a scheduled one-time or recurring program that launches a scene at a desired
time. You can program your controllers to create and control up to 32 events in your
home. Use this menu to schedule, create, name, edit, change, delete, activate and de-
activate events.
Example: If you plan on a romantic dinner, you can schedule an event to
automatically start a scene which dims the lights for the dinner.
Settings enu
Use this menu to customize your controller with your preferences for day/time, panic
mode settings, add a device to the Panic group, system information, replicating controller
information to a second controller, retrieving version information about your system, and
operating network discovery.
Away enu
The Away feature allows you to edit and control functions that give the impression that
your house is occupied when you’re away for an extended period of time. Use this menu
to activate, de-activate, and edit the Away feature.
Example: If you’re going on vacation you can schedule certain lights to turn on
during evening hours and then turn off at daybreak.
9
1
ALL
ON
ALL
OFF
Menu Back
2
34
56
78
9 10
PP
Menu/Save
button
OK button
ALL ON/Brighten
button
Back/Cancel
button
Arrow pad
All OFF/Dim
button
Number pad
Access the main menu
and save desired settings.
Battery Status
Indicator
Appears when battery
power is low.
Use this button to select
settings in menus.
Panic button
Trigger agroup of devicesto
turn off and on in a pattern
that attracts attention.
Turn all devicesin the ALL ON
group on at once. Brightens
selected dimmer switches.
Exit a menu screen
and return to the
previous menu.
Navigate through menus
and screens, create custom
names,and change
various settings.
Turn all devicesin the
ALL OFF group off at once.
Dims selected dimmer
switches.
Select and activate scenes.
Enter numerical info.
Devices
Mon 12:00 AM
Primary Controller
Callout
Indicates if it is the
primary controller.
Handh ld Controll r

Optional Accessories
10
RFWDC – Wall-mount 5-button Scene Controller
This controller stores up to five scenes for easy one-
touch activation and offers an ALL/OFF button for
turning all devices off controlled by this specific Scene
Controller. Mounts in any standard single-gang
wallbox and requires 120 VAC. A primary controller
( andheld, Tabletop, USB, or SDIO card) must be
used to program this device.
Optional Controll rs
RFUSB – USB Controller
RFUSB-PRO – USB Installer Controller
Allows for any PC or Laptop running Windows 2000
or newer to create, manage and control network
devices, scenes and events. Software and extension
cord is included with this controller and requires a USB
port. Can be set as a primary or secondary controller.
RF CC – SDIO Card Controller
Allows for any PDA running Windows Mobile to create,
manage and control network devices, scenes and
events. Software is included with this controller and
requires a SD card slot. Can be set as a primary or
secondary controller.