Coopers of Stortford Bed in Drawers 8228 User manual

Bed in Drawers 8228 Instructions
Please read carefully before use and retain for future reference.
PARTS LIST
a. 12x Dowel pins
b. 8x Cam screws
c. 8x Cam locks
d. 4x Base panel bolts
e. 2x hort front castors
f. 2x Long rear castors
g. 8x Drawer knobs bolts
h. 4x Nuts (for each castor)
i. 2x pacers (for rear castors)
j. 8x Drawer knobs
k. 4x Nuts (for base panel bolts)
L. 1x Top panel (drawer component)
M. 1x Front panel (drawer component)
N. 2x ide panels (drawer component)
O. 1x Folding bed frame
P. 1x Mattress
q. afety lock
ASSEMBLY
1. Carefully remove bed frame/mattress and
drawer components from the packaging
within both boxes (this unit will be delivered
in two boxes).
2. Place the folding bed frame, drawer
components and all fixings on a flat, clean
surface. Please check all the fixings are
enclosed before starting assembly. The castors
can be located in between the mattress. It is
recommended that assembly is
performed in the vicinity of the
desired location. The combined
weight of assembled Bed
in Drawers is 45kgs.
3. Take 1x top panel (L) and insert 4x
dowel pins (a) and 4x cam screws (b) with
screwdriver.
4. Take 1x side panel (N) and insert 4x dowel pins (a)
and 2x cam screws (b) with screwdriver.
5. Repeat process in point 4.
ab c d e fg hi j k
x12 x8 x8 x4 x2 x2 x8 x4 x2 x8 x4
a
L
N
O
P
M
N
c
c
c
c
g
g
g
g
g
g
j
j
j
j
j
j
j
j
d
d
d
d
g
g
c
q
i
i
h
h
h
f
e
e
f
h
c
c
c
a
a
a
a
a
a
a
a
a
b
b
b
b
b
b
a
b
b
a
Tools not included

WARNING
• Please do not place hands near hinges when opening
the bed.
• Please be careful when opening and closing the bed as
safety lock may cause potential harm to the user.
• The recommended weight load for this bed is 100kgs
(15st 10lb).
TECHNICAL SPECIFICATION
Measurements in box: H102cm xW86cm xD36cm
(40in x33in x14in).
Folded out: L191cm xW78cm xH34cm (75in x30in x13in).
DISPOSAL
• Dispose of all paper, cartons and plastic in accordance
with your local recycling regulations. At the end of the
product’s lifespan please dispose of it at an authorised
household waste recycling centre.
6. Take 1x front panel (M) and attach 8x drawer knobs (j) with 8x drawer knob bolts (g)
using a screwdriver.
7. Attach the front panel (M) and the two side panels (N) so that the dowel pins (a) and
cam bolts (b) align. Carefully secure all three panels together in place with 4x cam
locks (c) using a screwdriver.
Please note this part of the assembly may require two persons.
8. Attach the top panel (L) and the two side panels (N) and front panel (M) so that the
dowel pins and cam bolts align, carefully secure in place with 4x cam locks (c) using
a screwdriver.
Please note this part of the assembly may require two persons.
9. Carefully position the bed frame on its side
and insert 2x long rear castors (f) plus 2x
spacers (i) into the bed frame as shown.
Insert 2x short front castors (e) into the bed
frame as shown. ecure in place with 4x nuts
(h) for each castor with a spanner. Please
note that you will need to insert 1x spacer (i)
over each rear castor (f) before inserting it
into the bed frame.
10. Carefully reposition the bed frame (O) so it
sits on all 4 castors, release the safety lock
(q) and open the bed fully. Place the bed
frame against the inside of the constructed
mock drawer front. Insert 4x base panel
bolts (d) through the outside of both side
panels (N) and into the frame of the bed.
ecure in place with 4x nuts (k) and tighten
firmly with a spanner.
Please note this part of the assembly may require two persons.
11. Close the bed frame and mattress (P) and secure in place with the safety lock. Your
bed is now ready to use. Position the bed in the desired location.
Long rear castor
Base panel
bolt being
secured with nut
hort front castor