Coopers of Stortford G504 User manual

Solar Flower Border Light G504 Instructions for Use
Please read and retain these instructions for future reference v001: 23/03/20
ALWAYS POSITION IN DIRECT SUNLIGHT FOR BEST CHARGING
Dimensions
60cm high (including ground stake)
Battery 1 pc “AA” 1.2v 400Mah, Ni-MH, Rechargeable
ASSEMBLY INSTRUCTIONS / INSTRUCTIONS FOR USE:
Unpack the components carefully. Please check all parts have been removed from the packaging.
Stakes
To easily insert stakes into the ground, it is recommended to wet the ground first. To avoid damaging garden
stakes when inserting into the ground, select a spot in soft, rock-free soil. Insert the base of the stake first
then gently insert the rest of the stake into the base. DO NOT push directly against the solar cell or the
ornament housing containing the actual LED light.
BEFORE FIRST USE: Remove the protective film from the solar panel.
CHARGING AND OPERATION:
1. Set switch (located on the back of solar case) to “S (steady on)”OR “F (flash)”position. Charge the solar
product by placing it under direct sunlight for at least 8 hours.
2. The light will work automatically. It will charge under direct sunlight during the day time and illuminate
at night.
3.
NOTE: In order to test the lights simply cover the solar panel with your hand and the light should turn on
automatically.
IMPORTANT:
1. Install the solar product in an area where it can get direct sunlight.
2. Leave the switch to “S”OR “F”position.
3. Select an outdoor location away from other light sources at night, such as street lights. It may cause the
product not to turn on automatically at night.
4. Duration of light depends on solar product’s level of sunlight exposure, geographical locations, weather
conditions and the hours of daylight.
•EACH FLOWER LIGHTS UP IN A DIFFERENT
COLOUR TO GIVE YOU A RAINBOW OF
FLOWERS AT NIGHT TIME
•CHOOSE BETWEEN STEADY OR FLASHING
LIGHTS
•IDEAL FOR LINING YOUR BORDERS, BEDS,
PATHS ETC TO GIVE A PRETTY SHOW AT NIGHT
TIME
•SOLAR POWERED

Solar Flower Border Light G504 Instructions for Use
Please read and retain these instructions for future reference v001: 23/03/20
MAINTENANCE AND TROUBLESHOOTING:
1. Make sure the switch is set to “S” OR “F”
position.
2. Keep the solar panel clean.
3. If solar product does not light up after it has
been used for around 8 –12 months, replace
the rechargeable battery as it may be weak or
worn out. (Battery 1 pc “AA” 1.2v 400Mah, Ni-
MH, Rechargeable–Same equivalent type as
recommended must be used).
4. Battery replacement:
Step1: Unscrew the battery compartment cover by
using a Phillips head screwdriver (not included).
Step2: Remove the exhausted battery and install 1 pc
new AA rechargeable battery according to the +/-
polarity as beside image. Open the compartment
carefully and ensure that wire inside the battery
terminals is not damaged.
Step3: Replace battery compartment cover, screw it
back into position and make sure is properly sealed.
CARE AND CLEANING INSTRUCTIONS:
•Store the item in a cool, dry place.
•Wipe with a clean dry cloth.
BATTERIES
•Keep batteries away from children and pets.
•Do not mix used and new batteries.
•Install batteries in accordance with its polarity symbols.
•Remove the batteries if left for long periods.
•Never dispose of batteries in a fire.
•Battery disposal, spent or expired batteries must be properly disposed of and recycled in compliance
with local regulations. For detailed information, contact your local authority.
•Follow the battery manufacturer’s safety, usage, and disposal instructions.
DISPOSAL
•Dispose of all packaging, paper, cartons, plastic and plastic bags in accordance with
your local recycling regulations.
•Plastics –This is made from the following plastic.
Code &
Symbol
Type of Plastic
Low Density Polyethylene
Notes
Usually recyclable supermarket deposit points. Check other plastic
films as any non-polythene film e.g. cling film, crisp packets film lids
•At the end of the product’s lifespan please dispose of it at an authorised household
WEEE waste recycling centre.