COOPS & FEATHERS 223-02 User manual

D 2 pcs
(2) BOTTOM LOWER BASE
(2) VERTICAL SUPPORT POLE
(TOP END IS NOTCHED)
IDENTIFY ALL PARTS AND HARDWARE THAT ARE INCLUDED WITH YOUR
FOOD & WATER SHELTER. GRAB A SCREWDRIVER (OR HAND DRILL). FIND
A LEVEL PLACE TO BUILD IT AND AN EXTRA SET OF HANDS WOULD BE
HELPFUL. START BUILDING!
B
11
4
"
A
1
"
C
13
4
"
HORIZONTAL TOP SUPPORT BAR
(NOTCHED)
(4) VERTICAL SUPPORTS
1
x2
2
x2
3 x4
(2) ROOF TRUSSES
4
5
x2
(2) ROOF PANELS
TOP ROOF CAP
7
B
B
B
B
B
B
B
B
B
B
BB
.
.
.
.
..
.
.
B
12 pcs
C
C
.
1
3
3
2
3
3
1
2
4
C
2 pcs
6 x2
12 pcs
10 pcs
8 pcs
SET BOTTOM LOWER BASES (1) 28 INCHES APART PARALLEL TO EACH OTHER. TAKE THE
VERTICAL SUPPORT POLE (2) WITH THE NOTCH LOCATED ON THE TOP, FACING IN AND
USE TWO SCREWS (B) TO ATTACH TO THE BOTTOM LOWER BASE (1) ON THE INSIDE
THROUGH THE PRE-DRILLED HOLES. NEXT, ATTACH TWO OF THE VERTICAL SUPPORTS (3)
TO THE BASE OF THE VERTICAL SUPPORT POLE (2)
AND BOTTOM LOWER BASE (1) USING
A TOTAL OF FOUR SCREWS (B).
REPEAT FOR THE OTHER SIDE.
GRAB YOUR EXTRA SET OF HANDS AND THE HORIZONTAL TOP SUPPORT BAR (4) AND
INSERT NOTCHED ENDS INTO THE GROOVES LOCATED ON THE TOP OF THE VERTICAL
SUPPORT POLE (2). SECURE WITH SCREW (C) ON EACH END.
ASSEMBLY INSTRUCTIONS
Chicken Food & Water Shelter
Model# 223-02
23
1

A
A
A
.
A
.
OPTIONAL, BUT HIGHLY SUGGESTED IF YOU HAVE
HANGING FEEDER/WATER: PLACE PROVIDED HOOK(S) (D)
INTO DESIRED LOCATION(S) ON UNDERSIDE OF THE
HORIZONTAL SUPPORT BAR (4).
6
6
A
4 pcs
A
AA
A
.
7
A
4 pcs
.
CC
CC
.
.
...
.
C
4 pcs
.
CC
C
C
.
.
.
.
C
4 pcs
5
5
6
6
5
5
6
6
TURN COMPLETED ROOF OVER (RIGHT SIDE UP)
AND REST ONTO TOP OF CONSTRUCTED
FRAME. SECURE WITH TWO SCREWS (A) ON
EACH OUTSIDE END THROUGH PRE-DRILLED
HOLES.
PLACE TOP ROOF CAP (7) OVER CENTER
OF COMPLETED ROOF AND SECURE
WITH TWO SCREWS (A) ON EACH END.
TAKE YOUR OTHER ROOF TRUSS (5) AND INSERT THE NON-ATTACHED ROOF
PANEL INTO THE GROOVE/SLOT. ALIGN THE UNDERSIDE ROOF SUPPORTS WITH
THE EXTERIOR PRE-DRILLED HOLES AND LOOSELY TIGHTEN WITH TWO SCREWS
(C). INSERT THE OTHER ROOF PANEL INTO THE FINAL GROOVE/SLOT, ALIGN THE
UNDERSIDE ROOF SUPPORTS WITH THE EXTERIOR PRE-DRILLED HOLES AND
SECURE WITH TWO SCREWS (C). FULLY TIGHTEN THE PREVIOUS SCREWS.
TURN ONE ROOF TRUSS (2) AND ONE ROOF PANEL (6) UPSIDE DOWN. INSERT END OF
PLASTIC ROOF INTO GROOVE/SLOT AND ALIGN THE UNDERSIDE WOODEN ROOF
SUPPORTS WITH THE EXTERIOR PRE-DRILLED HOLES. SECURE TOGETHER WITH TWO
SCREWS (C)
.
TAKE THE OTHER ROOF PANEL (6) AND INSERT UPSIDE DOWN INTO THE
GROOVE/SLOT ON THE OTHER SIDE OF THE SAME ROOF TRUSS (2). ALIGN THE
UNDERSIDE ROOF SUPPORTS WITH THE EXTERIOR
PRE-DRILLED HOLES AND SECURE
WITH TWO SCREWS (C).
WE RECOMMEND EXTENDING THE LIFE OF YOUR FEED & WATER SHELTER WITH OUTDOOR PAINT OR A CLEAR FINISH. THIS SHELTER HAS BEEN STAINED BUT
USING A NON-TOXIC OUTDOOR PRODUCT OR A CLEAR POLYURETHANE WILL PROVIDE ADDITIONAL PROTECTION AGAINST RAIN, MOISTURE, HUMIDITY AND
SNOW FOR MANY SEASONS TO COME. NOW! SET OUTSIDE FOR YOUR FREE-RANGE BIRDS OR WITHIN YOUR COOP AREA AND LET YOUR BIRDS ENJOY!
4 5
6 7
8
9