Corby System 2000 User manual

Corby Industries, Inc.
1501 E. Pennsylvania Street, Allentown, PA 18109
http://www.corby.com
(800) OK-CORBY [phone]
Fax [phone] p/n 2300, Last Updated on December 13, 2001
SetupRemote Courier V.Everything Modem for Network Interface Controller (NIC)
Step 1. Set the DIP switches located at the bottom of the modem as in the table below.
12345678910
Ignore
DTR Verbal Result
Codes
Display
Result
Codes
Disable
Echo Disable Auto
Answer
CD On Originate
Mode Enable AT Commands Command Mode on
+++
Load
Factory
Settings
ON
down ON down OFF up ON down OFF up OFF up ON down ON down ON down OFF up
Step 2. Connect Modem to a Computer serial port. This is Com1, Com2, Com3, or Com4.
Step 3. Start the program HyperTerminal. Find this under your Start Programs menu. It may be under
Accessories or Communications.
Step 4. When you start HyperTerminal, a window will open asking you for the name and icon of a new
connection.
* Select ‘Cancel’.
* Under ‘File’, select ‘Open’.
* Change the ‘Look in’ folder to be where your System 2000 Modems folder is located.
(For example: C:\Program Files\Corby\Sys2000\Modems).
* Double-click on the file ‘Setup on Comx’ where ‘x’ is the com port the modem is connected to.
(The port is now configured for 115,200 baud, 8 data bits, no parity bit, 1 start bit, and hardware flow
control.)
Step 5. Still in HyperTerminal, do the following:
* Under ‘Transfer’, select ‘Send Text File’.
* Double-click on the file ‘Nic Modem Setup.txt.
Step 6. Reset your modem by turning power off and on. Disconnect modem from computer and install with the
System 2000 NIC. Be sure to use a Null Modem adapter (or Null Modem cable) between the System
2000 NIC and Modem. The easiest way to tell if you have the correct cable is by looking at the LEDs on
the NIC. If the CTS and/or DCD LEDs are on with the cable connected to the modem (and the modem is
powered up), then your cable is incorrect, and you need to insert a Null Modem Adapter between the NIC
and Modem. Connect the phone line to the modem ‘JACK’ connector.
Step 7. Go to System 2000 PC Modem Setup (see below). You may leave HyperTerminal running.
System 2000 Modem Instructions
for 3 Com Courier V.Everything Modems Page 1 of 2

System 2000 Modem Instructions
for3Com Courier V.Everything Modems Page2of 2
Corby Industries, Inc.
1501 E. Pennsylvania Street, Allentown, PA 18109
http://www.corby.com
(800) OK-CORBY [phone]
Fax [phone] p/n 2300, Last Updated on December 13, 2001
Setup Local Courier V.Everything Modem for System 2000 Computer
Step 1. Set the DIP switches located at the bottom of the modem as in the table below.
12345678910
Ignore
DTR Verbal Result
Codes
Display
Result
Codes
Disable
Echo Disable Auto
Answer
CD On Originate
Mode Enable AT Commands Command Mode on
+++
Load
Factory
Settings
ON
down OFF up ON down ON down OFF up OFF up OFF up ON down OFF up OFF up
Step 2. Connect Modem to a Computer serial port. This is Com1, Com2, Com3, or Com4.
Step 3. If you are continuing from the NIC modem and HyperTerminal is still running, proceed to step 5.
Otherwise, start the program HyperTerminal. Find this under your Start Programs menu. It may be under
Accessories or Communications.
Step 4. When you start HyperTerminal, a window will open asking you for the name and icon of a new
connection.
* Select ‘Cancel’.
* Under ‘File’, select ‘Open’.
* Change the ‘Look in’ folder to be where your System 2000 Modems folder is located.
(For example: C:\Program Files\Corby\Sys2000\Modems).
* Double-click on the file ‘Setup on Comx’ where ‘x’ is the com port the modem is connected to.
(The port is now configured for 115,200 baud, 8 data bits, no parity bit, 1 start bit, and hardware flow
control.)
Step 5. Still in HyperTerminal, do the following:
* Under ‘Transfer’, select ‘Send Text File’.
* Double-click on the file ‘PC Modem Setup Step 1.txt. The modem will respond with ‘OK’.
* Double-click on the file ‘PC Modem Setup Step 2.txt. The modem will respond with ‘OK’.
* Close HyperTerminal.
Step 8. Reset your modem by turning power off and on. Start the System 2000 Application and follow the
instructions for adding a NIC to your system. Make sure you do not use a Null Modem adapter (or Null
Modem cable) between the System 2000 Computer and Modem. You will not be able to talk to the
modem if you do. Connect the phone line to the modem ‘JACK’ connector. Be sure to enter the NIC’s
phone number on the ‘Remote Settings’ tab of the interface properties.