Miranda NV9640 User manual

NV9640
Control Panel
User’s Guide
Miranda Technologies Inc.
3499 Douglas B. Floreani
Montreal, Quebec
Canada H4S 2C6

ii Rev 0.9a • 13 Oct 09
NV9640 Control Panel—User’s Guide
•Revision: 0.9a
•Software Version: tbd
•Part Number: UG0048-00
• Copyright: © 2009 Miranda Technologies, Inc. All rights reserved.
• No part of this manual may be reproduced in any form by photocopy, microfilm, xerography or
any other means, or incorporated into any information retrieval system, electronic or mechani-
cal, without the written permission of Miranda Technologies, Inc.
• The information contained in this manual is subject to change without notice or obligation.
• All title and copyrights as well as trade secret, patent and other proprietary rights in and to the
Software Product (including but not limited to any images, photographs, animations, video,
audio, music, test, and “applets” incorporated into the Software Product), the accompanying
printed materials, and any copies of the Software Product, are owned by Miranda Technologies,
Inc. The Software Product is protected by copyright laws and international treaty provisions.
Customer shall not copy the printed materials accompanying the software product.
Notice
The software contains proprietary information of Miranda Technologies, Inc. It is provided under a
license agreement containing restrictions on use and disclosure and is also protected by copyright
law. Reverse engineering of the software is prohibited.
Due to continued product development, the accuracy of the information in this document may
change without notice. The information and intellectual property contained herein is confidential
between Miranda and the client and remains the exclusive property of Miranda. If you find any
problems in the documentation, please report them to us in writing. Miranda does not warrant that
this document is error-free.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Declaration of Conformance (CE)
All of the equipment described in this manual has been designed to conform with the required
safety and emissions standards of the European Community. Products tested and verified to meet
these standards are marked as required by law with the CE mark. (See Symbols and Their Mean-
ings on page v.)

NV9640 Control Panel • User’s Guide iii
When shipped into member countries of the European Community, this equipment is accompanied
by authentic copies of original Declarations of Conformance on file in Miranda USA offices in
Grass Valley, California USA.
Trademarks
Miranda is a registered trademark of Miranda Technologies, Inc.
Brand and product names mentioned in this manual may be trademarks, registered trademarks or
copyrights of their respective holders. All brand and product names mentioned in this manual serve
as comments or examples and are not to be understood as advertising for the products or their man-
ufactures.
Software License Agreement and Warranty Information
Contact Miranda for details on the software license agreement and product warranty.
Technical Support Contact Information
Miranda has made every effort to ensure that the equipment you receive is in perfect working order
and that the equipment fits your needs. In the event that problems arise that you cannot resolve, or
if there are any questions regarding this equipment or information about other products manufac-
tured by Miranda, please contact your local representative or contact Miranda directly through one
of the appropriate means listed here.
• Main telephone: [phone] (9 am to 9 pm PST)
Fax: [phone]
In the Americas, call toll-free: [phone] (9 am to 9 pm EST)
In Europe, the Middle East, African or the UK, call [phone] (9 am to 6 pm, GMT)
In France, call [phone] (9 am to 5 pm, GMT + 1)
In Asia, call [phone] (9 am to 5 pm, GMT + 8)
In China, call [phone]
• Emergency after hours: toll-free: [phone]
Tel: [phone]
•E-Mail:
In the Americas, [e-mail]
In Europe, the Middle East, African or the UK, [email protected]
In France, euro[email protected]
In Asia, [email protected]
In China, [email protected]
• Website: http://www.miranda.com
• Mail Shipping
Miranda USA Miranda USA
P.O. Box 1658 125 Crown Point Court
Nevada City, CA 95959, USA Grass Valley, CA 95945, USA
Note Return Material Authorization (RMA) required for all returns.

iv Rev 0.9a • 13 Oct 09
Change History
The table below lists the changes to the Control Panel User’s Guide.
• User’s Guide Part # UG0048-00
• Software version: tbd
Restriction on Hazardous Substances (RoHS)
Miranda is in compliance with EU Directive RoHS 2002/95/EC governing the restricted use of cer-
tain hazardous substances and materials in products and in our manufacturing processes.
Miranda has a substantial program in place for RoHS compliance that includes significant invest-
ment in our manufacturing process, and a migration of Miranda product electronic components and
structural materials to RoHS compliance.
It is our objective at NV to maintain compliance with all relevant environmental and product regu-
latory requirements. Detailed information on specific products or on the RoHS program at Miranda
is available from Miranda Customer Support at
1-800-719-1900 (toll-free) or
1-530-265-1000 (outside the U.S.).
Rev Date ECO Description Approved By
0.9a 13 Oct 09 — Draft D. Cox

NV9640 Control Panel • User’s Guide v
Important Safeguards and Notices
This section provides important safety guidelines for operators and service personnel. Specific
warnings and cautions appear throughout the manual where they apply. Please read and follow this
important information, especially those instructions related to the risk of electric shock or injury to
persons.
Symbols and Their Meanings
The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the pres-
ence of dangerous voltages within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle alerts the user to the presence of important
operating and maintenance/service instructions.
The Ground symbol represents a protective grounding terminal. Such a terminal must be connected
to earth ground prior to making any other connections to the equipment.
The fuse symbol indicates that the fuse referenced in the text must be replaced with one having the
ratings indicated.
The presence of this symbol in or on Miranda equipment means that it has been designed, tested
and certified as complying with applicable Underwriter’s Laboratory (USA) regulations and rec-
ommendations.
The presence of this symbol in or on Miranda equipment means that it has been designed, tested
and certified as essentially complying with all applicable European Union (CE) regulations and
recommendations.
Warning Any instructions in this manual that require opening the equipment cover or
enclosure are for use by qualified service personnel only. To reduce the risk of
electric shock, do not perform any service other than that contained in the
operating instructions unless you are qualified to do so.

vi Rev 0.9a • 13 Oct 09
General Warnings
A warning indicates a possible hazard to personnel which may cause injury or death. Observe the
following general warnings when using or working on this equipment:
• Heed all warnings on the unit and in the operating instructions.
• Do not use this equipment in or near water.
• This equipment is grounded through the grounding conductor of the power cord. To avoid elec-
trical shock, plug the power cord into a properly wired receptacle before connecting the equip-
ment inputs or outputs.
• Route power cords and other cables so they are not likely to be damaged.
• Disconnect power before cleaning the equipment. Do not use liquid or aerosol cleaners; use
only a damp cloth.
• Dangerous voltages may exist at several points in this equipment. To avoid injury, do not touch
exposed connections and components while power is on.
• Do not wear rings or wristwatches when troubleshooting high current circuits such as the power
supplies.
• To avoid fire hazard, use only the specified fuse(s) with the correct type number, voltage and
current ratings as referenced in the appropriate locations in the service instructions or on the
equipment. Always refer fuse replacements to qualified service personnel.
• To avoid explosion, do not operate this equipment in an explosive atmosphere.
• Have qualified service personnel perform safety checks after any service.
General Cautions
A caution indicates a possible hazard to equipment that could result in equipment damage. Observe
the following cautions when operating or working on this equipment:
• When installing this equipment, do not attach the power cord to building surfaces.
• To prevent damage to equipment when replacing fuses, locate and correct the problem that
caused the fuse to blow before re-applying power.
• Use only the specified replacement parts.
• Follow static precautions at all times when handling this equipment.
• This product should only be powered as described in the manual. To prevent equipment dam-
age, select the proper line voltage on the power supply(ies) as described in the installation doc-
umentation.
• To prevent damage to the equipment, read the instructions in the equipment manual for proper
input voltage range selection.
• Some products include a backup battery. There is a risk of explosion if the battery is replaced by
a battery of an incorrect type. Dispose of batteries according to instructions.
• Products that have (1) no on/off switch and (2) use an external power supply must be installed
in proximity to a main power output that is easily accessible.

NV9640 Control Panel • User’s Guide vii
Table of Contents
Chapter 1 Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chapter Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
The PDF Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Terms, Conventions and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Other Documentation and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Panel Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Function Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Alphanumeric Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Display Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tally Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Other NV9640 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing Software and Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adding a Panel to a NV9000 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
NV9640 Panel Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Regions of the Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuration Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Commitment Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Panel Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Checkbox Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Button Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Button Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Button Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
‘Edit Navigation Button’ Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Automatic Fill Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Button Page List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Tally (GPIO) Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Selection Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Selection Button Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
XY Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MD Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
XY Mode —Normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
XY Mode —Hold Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MD Mode —Normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MD Mode —Hold Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

viii Rev 0.9a • 13 Oct 09
Table of Contents
Single-Destination Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Multi-Destination Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
How to Configure MD Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
MD Destination Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
User-Definable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
User-Selectable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Global Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Referencing a Suffix Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Referencing a Navigate Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Composing Suffix Templates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Template Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Composing Navigate Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Template Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Button Legends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Level Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
MD Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Operating Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Broadcast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Clear Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Default State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Destination Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Destination Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Free Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Level Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Navigate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Global Navigate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Page Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Page Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Panel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Preset Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Previous Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Quick Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Salvo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Save Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Selection Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Source/Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Source is Master. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Take . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Undefined. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
XY/MD Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

NV9640 Control Panel • User’s Guide ix
Table of Contents
Lock, Protect, and Release. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Takes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
XY Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Single-Destination Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
MD Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Broadcast Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Making Broadcast Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Removing Broadcast Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Salvo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Menu Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Software Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
LCD Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Chapter 6 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
The Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
GPIO Configuration Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
The GPIO Section of the NV9640 Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Configuring Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Configuring Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Chapter 7 Technical Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
NV9640 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Initial Panel State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Chapter 8 Misc. Topics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
LCD Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Power Cord Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

xRev 0.9a • 13 Oct 09
Table of Contents

NV9640 Control Panel • User’s Guide 1
1. Preface
Chapter 1 is an introduction to the NV9640 User’s Guide. It presents the following topics:
•Chapter Structure
•The PDF Document
•Terms, Conventions and Abbreviations
Chapter Structure
The following chapters provide detailed information regarding the NV9640 Control Panel:
• Chapter 1, Preface, (this chapter) outlines ways to use this guide.
• Chapter 2, Introduction, provides a functional description of the NV9640.
• Chapter 3, Installation, provides installation, connection, and initialization instructions.
• Chapter 4, Configuration, provides configuration instructions.
This chapter is for configurers, primarily.
• Chapter 5, Operation, provides operating instructions.
This chapter is for operators, primarily.
• Chapter 6, GPIO, describes the tally (a.k.a. GPIO) interface and tells you how to configure it.
• Chapter 7, Technical Details, provides electrical, mechanical, and environmental specifications,
product drawings, and default settings.
• Chapter 8, Misc. Topics, presents a glossary and miscellaneous instructions and information.
•AnIndex is also provided for your reference.
The PDF Document
This guide is provided in PDF format, allowing you to use Acrobat’s “bookmarks” to navigate to
any desired location. You can also easily print a hardcopy. Please note:
• Use the Table of Contents or the bookmarks page to jump to any desired section.
• Many hyperlinks are provided within the chapters.
• Use the Index to jump to specific topics within a chapter. Each page number in the index is a
hyperlink.
• Use Acrobat’s ‘Go to Previous View’ and ‘Go to Next View’ buttons to retrace your complete
navigational path.

2Rev 0.9a • 13 Oct 09
1. Preface
Terms, Conventions and Abbreviations
• Use the ‘First Page’, ‘Previous Page’, and ‘Next Page’, and ‘Last Page’ buttons to go to the
first, previous, next, or last page within a PDF file.
• Use Acrobat’s extensive search capabilities, such as the ‘Find’ tool and ‘Search’ tool to perform
comprehensive searches as required.
Terms, Conventions and Abbreviations
The following conventions are used throughout this guide:
• The symbol Sdenotes either an example or a special message.
• Entries enclosed in single quotation marks or Capital Letters denote physical control panel but-
tons, configuration buttons, or menu items.
• Click ‘Apply’ to ...
• Press the SRC 12 button ...
The following terms and abbreviations are used throughout this guide:
• The term “control panel” refers to the NV9640 control panel and to NV96xx control panels, in
general.
• “High tally” means that a button is brightly illuminated.
• “Low tally” means that a button is illuminated at low intensity. Most buttons assume a low tally
state until selected.
• “MD” is an abbreviation for multi-destination.
• “SE” is an abbreviation for NV9000-SE Utilities.
Other Documentation and Software
You should read and be familiar with the material presented in the following documents:
• NV9000 Quickstart Guide.
• NV9000-SE Utilities User’s Guide (or NV9000-SE Utilities help files).
• The router manuals for whatever routers you have in your system.
You should also be familiar with the NV9000-SE Utilities software and NV9000 router control sys-
tems.
Note To display the navigation buttons, right-click the Tool Bar area, and check
‘Navigation’.

NV9640 Control Panel • User’s Guide 3
2. Introduction
Chapter 2 provides a functional description of the NV9640. It presents these topics:
•Summary
•Panel Organization
•Modes of Operation
•Other NV9640 Functions
Summary
The NV96401is a hierarchical control panel featuring 30 LCD function buttons (illuminated in var-
ious colors and having 1 to 3 lines of text) and a small vacuum fluorescent display having 8 lines of
42 characters. It can operate in X-Y mode or in multi-destination (MD) mode. Operators can switch
between modes at any time.
This 2RU panel is organized as shown in figures 2-1 and 2-2:
Figure 2-1. NV9640 Front
At the rear, in addition to power, serial, and network connectors, is a 25-pin GPIO (tally) connector
that supports 4 optically isolated relay outputs and 8 optically isolated inputs:
Figure 2-2. NV9640 Rear
1 An equivalent NV9640V —a GUI that is called a “virtual panel”— is available. It emulates the NV9640.
Character Display 30 Function Buttons
GPIO (tally)Ethernet
Serial (RS-232)
Power

4Rev 0.9a • 13 Oct 09
2. Introduction
Panel Organization
The NV9640 provides a tree-structured (or hierarchical) button layout. Configurers can define a
“tree” of buttons in such a way that each of the 30 LCD buttons can either (1) execute a function or
(2) select a subtree (i.e., present an entirely new set of functions at a different level in the tree). The
tree, with its subtrees, is not limited in size.
We use the term “button page” or “page” to mean the set of 30 button functions at any particular
level in the tree.
Configurers will use ‘Navigate’ buttons to create new button pages (subtrees). During operation,
NV9640 users will press a ‘Navigate’ button to access a subtree. However, ‘Navigate’ buttons are
typically not labeled “Navigate”; they would be labeled according to the specific function they per-
form in your system.
The panel can also display predefined button pages. For instance, a “category” button, when
pressed, will display one or more pages of sources or destinations through which the operator may
browse. A “menu” button presents a page of menu options.
Panel Organization
Function Buttons
The NV9640 has an array of 30 LCD buttons. Each has 3 lines of text (up to 8 characters per line).
The buttons can display one of seven colors dynamically: nominally red, green, blue, purple,
amber, yellow, or grey. An eighth color exists —“dark” —when the LCD is off.
During configuration, you can assign any of the 7 colors to a button.
Each LCD button has four levels of brightness: off, low, medium, and high, and supports three
operational levels: high tally, low tally, and off. High tally can be either medium or high brightness
and low tally can be either low or medium brightness. High tally is always constrained to be
brighter than low tally. See LCD Buttons, page 79, for a color chart.
Although you can see a list of the pages in the tree during configuration, the structure of the tree is
not evident on the panel itself. The panel operator must commit the tree structure to memory to be
able to use the panel. It is up to the person configuring the panel to design a usable tree structure.
Some buttons functions are assigned by the system depending on the context. For example. if a but-
ton page is to represent all sources in a category, and that list changes, the button subtree adjusts in
size dynamically. The panel software adds a “forward” button and a “back” button if there are more
sources than buttons. Pressing the ‘Forward’ button takes you to the next page of sources. Pressing
the ‘Back’ button takes you to the previous page of sources.
Some button states depend on context. Many buttons remain unlit when their functions are dis-
abled. For example, ‘Page Up’ and ‘Page Down’ buttons remain unlit until there is an opportunity
to scroll up or down, respectively. By default, an XY/MD button turns green for X-Y mode and
amber for multi-destination mode. ‘Save Preset’ goes low tally when you press ‘Clear Preset’.
The LCD buttons display a menu if the operator presses a menu button. When the operator make a
menu selection, viewable data are displayed on the LCD buttons. In some cases, the operator can
enter data (such as panel ID or LCD brightness) using buttons that allow data entry.

NV9640 Control Panel • User’s Guide 5
2. Introduction
Panel Organization
Configurers can define ‘Selection’ buttons that select a level during a breakaway setup. (You must
do so if the operator is to make such selections.)
Scrolling is necessary when a list of items —for instance, source devices —exceeds the number of
buttons available for the items. The panel adds ‘Forward’ and ‘Back’ buttons as necessary. Panels
that use multi-destination mode will probably require ‘Page Up’ and ‘Page Down’ buttons.
Alphanumeric Display
The 8×42 alphanumeric display provides real-time feedback for the operators as they press buttons
to execute takes and other operations. The panel functions in two modes: X-Y or multi-destination.
The display changes according to the mode:
In either case, the display has 8 rows. Operators might need to scroll the display to see additional
information. (‘Page Up’ and ‘Page Down’ buttons are for scrolling the display.)
Display Fields
The display has 4 columns:
• Level/Dest.
In X-Y mode, this column identifies the levels of the currently selected destination. That desti-
nation is identified in the information column. In the illustration above, ‘VTR 1’ was selected.
Operators might need to scroll to see or select a level.
In MD mode, the ‘Level/Dest’ column presents all the MD destinations defined in the NV9640
configuration. (Actual destinations are defined in the NV90002configuration.) Operators might
need to scroll to see or select a destination.
•Status.
The status column indicates what source was routed to the destination.
In X-Y mode, the status column represents the levels of a source or the levels of multiple
sources under breakaway. These are called the current source(s). The presence of ‘--------’ in
the status or preset columns means that that particular level is not defined for the destination.
Therefore, no source selection for that level is possible. The illustration above shows that levels
HD and ‘TimeCode’ are not defined for VTR 1.
In MD mode, the status column represents the sources routed to each of the destinations in the
‘Level/Dest’ column. Again, these are the current sources.
Preset Status Level/Dest
X  Y   HD
X  Y   HD
Dest CAM1 SD
Dest CAM1 SD
VTR 1 CAM1 AUDIO 1
VTR 1 CAM1 AUDIO 1
+CAM1 AUDIO 2
+CAM1 AUDIO 2
+CAM1 AUDIO 3
+CAM1 AUDIO 3
+CAM1 AUDIO 4
+CAM1 AUDIO 4
  TIMECODE
  TIMECODE
Page 1
Page 1
Preset Status Level/Dest
Mult Dest CAM1 VTR1
Mult Dest CAM1 VTR1
CAM1 VTR2
CAM1 VTR2
CAM1 VTR3
CAM1 VTR3
CAM1 VTR4
CAM1 VTR4
CAM1 VTR5
CAM1 VTR5
CAM1 VTR6
CAM1 VTR6
CAM1 VTR7
CAM1 VTR7
Page 1 CAM1 VTR8
Page 1 CAM1 VTR8
X-Y mode Multi-destination mode
2 Or in the NV915 configuration.

6Rev 0.9a • 13 Oct 09
2. Introduction
Panel Organization
•Preset.
The preset column indicates what source will be routed to a destination when the operator
presses the ‘Take’ button.
In X-Y mode, the preset column represents the levels of a source or the levels of multiple
sources under breakaway. These are called the preset source(s). After the take, they disappear
from the preset column and re-appear in the status column, reflecting that the preset sources
have now become current sources.
In MD mode, the preset column indicates the sources that will be routed to selected destinations
in the ‘Level/Dest’ column. These are the preset source(s). After the take, they disappear from
the preset column and re-appear in the status column, reflecting that the preset sources have
now become current sources.
• Information (not labeled).
The first entry in this column is “X - Y” or ‘MultiDest” unless you have entered salvo mode,
menu mode, or setup mode. See chapter 5 for those topics.
The bottom-most entry in this column is always the page number of the display.
In X-Y mode, the second entry is always the word “Dest” as a title for the third entry which
identifies the current destination. In the preceding illustration, the current destination was
VTR--1.
In MD mode, there are no entries in this column other than “MultiDest” and the page number.
Flags
The display also shows flags of different kinds next to the sources and destinations.
Selection Marks
At the far right of the display are marks (3 small bars) that turn on to indicate selections.
In X-Y mode, the marks turn on to indicate that a level is selected and are not visible otherwise.
(The operator makes level selections in the button array.)
In MD mode, a mark appears to the right of the currently selected destination (and of all the cur-
rently selection destinations in hold mode).
Other Signs
A plus sign (+) indicates that additional information is available. There is an ‘Info’ button that
operators may press to view the additional information.
In MD mode, an asterisk (*) directly after a source indicates a breakaway on that destination.
An ‘L’ indicates that a device has been locked. A ‘P’ indicates that a device has been protected.
NV9640 operators may lock, protect or release destinations. It is important for operators to know
that other operators may lock, protect, or release sources and destinations.
Tally Interface
At the rear of the panel is a DB25 connector that provides 8 tally inputs and 4 tally outputs. (The
outputs are solid state relay outputs.) Both inputs and outputs are optically isolated.

NV9640 Control Panel • User’s Guide 7
2. Introduction
Modes of Operation
During configuration, you can construct Boolean logic that switches the outputs on. The terms of
the logic expressions are states of the source and destination devices, etc., controlled by the
NV9000 control system.
During configuration, you can prescribe NV9640 behavior that depends on the tally inputs.
What you connect to the tally interface is, of course, up to you. Miranda provides a breakout cable
(WC0053) for the tally connector as a purchase option.
The NV9000-SE Utilities on-line help documentation calls the tally interface a GPIO interface. On
the rear of the panel, it is labelled a “GPI interface.”
See Chapter 6, GPIO, on page 65, for complete detail.
Modes of Operation
The panel operates in either X-Y mode or multi-destination (MD) mode. A single button (XY/MD)
can toggle between the modes. A third mode —called “single-bus,” “single-destination,” or “but-
ton-per-source” mode —can be emulated in either X-Y mode or MD mode.
The primary modes of operation are:
•X-Ymode
—individual control of all router levels. Choose a destination, optionally choose
desired breakaway levels, choose a source, and press ‘Take’ to complete a desired route.
• Multi-destination mode —lets you control multiple destinations. The LCD buttons display des-
tinations and sources. You can scroll through destination lists using the ‘Up’ and ‘Down’ but-
tons. Select a destination using selection buttons, choose a source, and repeat for all desired
routes. Then press ‘Take’. Takes are “all level,” and breakaways cannot be performed.
SThe ‘Hold’ button allows you to select many MD destinations at once.
• Single-destination mode.
Single-destination” mode is not a distinct mode, but we mention it because it is a mode on some
other panels and can be simulated on the NV9640. It can be combined with the other two
modes. You can create many different forms of “single-destination” mode. This mode may in
fact have more than a single destination.
To understand single-destination mode, you must understand the different button types. Please
read the Configuration and Operation chapters and then see Single-Destination Mode
(page 35).
The secondary modes of panel operation are:
• Setup mode —where the NV9640 is freshly powered up, but disconnected from the network. In
this mode, you can preset the NV9640’s panel ID and perform a few diagnostic tasks.
• Salvo mode —pressing a Salvo button (and then the ‘Take’ button) executes a salvo. (The dura-
tion of a salvo is indeterminate.)
• Menu mode —pressing a Menu button places the NV9640 in “menu” mode. In menu mode, the
LCD button array becomes a menu that changes as needed during menu operation.
Other modes of operation are:
• Hold mode —when you press the ‘Hold’ button, hold mode becomes active and when you press
it again, hold mode becomes inactive. See Hold on page 53.

8Rev 0.9a • 13 Oct 09
2. Introduction
Other NV9640 Functions
• Save preset mode —when you press the ‘Save Preset’ button, ‘Save Preset’ mode becomes
active and when you press it again, ‘Save Preset’ mode becomes inactive. See Save Preset on
page 55.
Other NV9640 Functions
The NV9640 can be configured to perform the following additional functions:
• Previous source, free source, “quick” source, and source/destination buttons.
• Return to a pre-defined (or default) state.
• Hold breakaway levels.
• System salvos.
• Lock/protect/release for destinations.
• Forced release of locked or protected devices.
• Device selection using indexes or suffixes.
The NV9640 provides the following additional features:
• The NV9640 supports multiple-level breakaways in X-Y mode. This lets you route multiple
sources to the same destination on different levels.
• The panel supports gang or dub switching in multi-destination mode.
• Broadcast data routing in X-Y mode.
• Level mapping.
• Button page “templates”— global navigation templates and suffix templates —for easier con-
figuration.

NV9640 Control Panel • User’s Guide 9
3. Installation
Chapter 3 provides installation and connection instructions. It presents the following topics:
•Package Contents
•Installation
•Installing Software and Documentation
•Installation
•Testing
Package Contents
If you have ordered one or more NV9640 control panels from Miranda, inspect the shipping con-
tainer for damage. If you find any container damage, unpack and inspect the contents. If the con-
tents are damaged, notify the carrier immediately.
As you unpack the shipping container, look for the packing slip and compare it against the contents
to verify that you received everything as ordered. If anything is missing (or if you find equipment
damage unrelated to shipping), please contact technical support. Refer to Technical Support Con-
tact Information on page iii.
Depending on your order, the NV9640 items that can ship include:
• One or more NV9640 control panels.
• One or two power supplies for each NV9640, with straps that secure the AC power cords to the
power supplies.
• A CD containing this user’s guide (this document), NV9000-SE Utilities software, and other
material.1
• Optional WC0053 breakout cable.
The package does not contain network cables, serial cables, or mounting screws.
You do not need to take any special precautions regarding ESD.
This document does not address the shipment or installation of any other equipment or software
that can be used in conjunction with the NV9640 (including the NV9000 system controller, NV915
system controller, other NV96xx control panels, EC9700 GUI, EC9710 GUI, and configuration
programs such as UniConfig or the NV9000-SE Utilities).
This document does briefly address the use of NV9000-SE Utilities and the Panel IP Configuration
Utility as they pertain to panel configuration.
1. You can obtain software and documentation updates through Miranda customer service.

10 Rev 0.9a • 13 Oct 09
3. Installation
Installation
Installation
Follow these steps to install a NV9640 control panel:
1 Mount, and secure, the panel in the rack.
The NV9640 is designed to mount in a 19″rack. Rack-mounting is not a requirement.
Place the panel in position in your rack. Attach the panel to the rack frame, using screws appro-
priate for your rack. The panel’s mounting slots are spaced 3.00″(76.2 mm) vertically and allow
approximately 1/8″(3 mm) of movement horizontally.
2 We assume that you have an Ethernet switch connected to the “Panel and Router Network” port
of your system controller. Connect an Ethernet cable from that switch to the RJ-45 port at the
rear of the NV9640.
3 Connect one or both power supplies. First connect the 4-pin connector to PS1 or PS2 on the rear
of the router. The connectors are keyed and snap into place. There is only one way they fit. Do
not force them. Then connect the power supply to AC power.
A second power connection is for redundancy only (protection against failure) and is not a
requirement for operation.
Refer to Power Specifications on page 71 for details on the PS0001 power supply. See also
Power Cord Retention on page 80.
4 Connect tally (GPIO) input devices and output devices at the DB25 GPI connector.
You can use the optional WC0053 breakout cable to make these connections.
See Chapter 6, GPIO, on page 65 for detail regarding the tally interface.
Installing Software and Documentation
This document is available through several sources, including the Miranda web site and the Router
Control Software and Documentation CD (SB0033).
You must use NV9000-SE Utilities to configure the NV9640 control panel. Contact Miranda if you
need to obtain the latest version of this NV9000 configuration software.
You may use the Panel IP Configuration Utility if you want to your NV9640 to have a static IP
address or to use DHCP. The panel, as it comes from the factory, defaults to DHCP.
2
1
4
3
Receptacle
n.c.
n.c.
GND
12VDC
4
3
2
1
GND
12 VDC
n.c.
n.c.
Plug