Core Products DALLAS DL908 User manual

Height: 1600 mm
Width: 686 mm
Depth: 423 mm
150min
PLEASE RETAIN THIS INSTRUCTION LEAFLET FOR FUTURE REFERENCE.
BATCH NUMBER
DALLAS BOOKCASE
REF. DL908
BEFORE YOU START ASSEMBLY
Please check that you have all the
correct parts and fittings as detailed.
In the unlikely event that you require to
order spare parts or fittings please refer
to your delivery note for details of how
to order using our Parts website.
www.coreproducts.co.uk/parts
Customer help line: 01738 630555
We recommend that you build your
furniture on top of a soft clean cover to
ensure the unit does not get marked or
damaged during assembly.
02/10/2020
Thank you for choosing this furniture.
BEFORE YOU START ASSEMBLY please store the carton for 48 hours or more so the contents can acclimatise.
PLEASE RETAIN ALL PACKING UNTIL YOU HAVE COMPLETED ASSEMBLY.
Information about your furniture.
This furniture range has been carefully crafted from melamine faced manufactured board.
Each piece is manufactured to the highest standards using specialised computer controlled machinery to ensure accuracy.
Caring for your furniture.
Extreme temperature can cause slight movements in the board material so please avoid placing your furniture close to radiators or other direct sources of heat.
Please avoid exposing your furniture to continued bright sunlight as this can affect the colour.
Any fluid spills should be removed as quickly as possible.
Always lift your furniture when moving as dragging may cause damage to your furniture or flooring.
Always use place mats, coasters or tablecloths to help protect against scratches and accidentally dropped items. Always use heat resistant mats when placing hot or
cold items on to surfaces.
Do not sit or stand on your furniture.
After care.
Wipe all surfaces with a dry cloth and the occasional use of a normal household furniture polish and a household glass cleaner on glass surfaces.
Please do not use detergents or chemicals on your furniture.
After assembly remove all visible component identification stickers, these should remove easily however any remaining adhesive residue can be easily removed with
a label adhesive removal liquid available from most DIY or hardware stores.
Specialist glass care.
Glass can be marked with continual use by contact with rough surfaced objects or strong coloured fluids. In the unlikely event that the glass is damaged it must be
replaced without delay with toughened glass made to specification BS EN12150. Please consult a specialist glass retailer for this.

ASSEMBLY HARDWARE
x66
Dowel Minifix Bolt
x38
Cover Caps
x20
Colour 1
x38
Minifix Cams
x2
Roll Over Kit
(Includes screws)
Page 2
ASSEMBLY PARTS MAX SUGGESTED LOADS
A - x1
B - x1
C - x1
D - x1
E - x1
Soft Closing End
Panel Hinge (SCEPH)
(Includes screws)
x3
Leg
x5
Screw
(25,4mm)
x10
FI - x1
FS- x1
G - x1
H - x3
I - x5
K - x1
L - x1
M - x2
N - x2
Cover Caps
x22
Colour 2
10 Kg.
8 Kg.
D
J
G
N
I
M
A
C
H
LH
I
N
M
B
E
K
J
H
I
I
I
FI
FS
8 Kg.
8 Kg.
5 Kg.
5 Kg.
5 Kg.
8 Kg.
Screw
(50,8 mm)
x4
J - x2

1
2
3
K
Hx3
C
12
Gently hit to adjust.
Repeat this in the
following steps.
Gently hit to adjust.
Repeat this in the
following steps.
Soft Closing End
Panel Hinge (SCEPH)
Page 3

Page 4
4
5
6
Gently hit
to adjust.
C
H
H
H
K
Turn minifix cams to
the right to tighten.
2
1
Rotate 180° /
Gire 180°
E
E
C
H
H
H
K
Gently hit
to adjust.

7
8
Page 5
FI
FS
G
G
FS
FI
E
C
H
H
H
K
Gently hit
to adjust.

9
10
11
Page 6
Gently hit
to adjust.
D
D
E
C
H
H
H
K
FI
B
CAREFULLY FLIP THE FURNITURE / !

12
Page 7
13
14
Ix5
Gently hit
to adjust.
D
C
H
H
H
K
E
B
Slide the back panels
inside the cabinet
D
C
E
FS
FI
G
M
M
N
N
CAREFULLY FLIP THE FURNITURE / !
Close the panel hinges
H
H
E

16
17
Page 8
I
I
I
I
I
J
J
J
I
I
I
I
I
Gently hit
to adjust.
Gently hit
to adjust.
15
Jx2
25 25
MM
FRONT
FRONT
192 128
!

18
19
20
A
Gently hit
to adjust.
D
E
H
H
H
C
K
I
I
I
I
I
J
J
Slide the module
inside the cabinet
B
A
D
C
H I
I
I
J
I
H
H
K
CAREFULLY FLIP THE FURNITURE / !
Page 9

21
Page 10
22
1
Depth adjustment
2
Side adjustment
3
Height adjustment
45
D
C
H
H
H
A
B
I
I
I
I
J
L
CAREFULLY FLIP THE FURNITURE / !
C
G
FS
FI
A
N
N
M
M
25,4 mm
50,8 mm
Door Installation
Hinge adjustment
Secure Hinge

23
Page 11
After you finish the
adjustment of the cams,
cover them with the
cover caps. AAfter you finish
assembling the cabinet,
take off the adhesive
letters.
-WARNING! TIPPING HAZARD – Unanchored furniture can tip over
-WARNING: CHECK FOR HIDDEN PIPES AND CABLES BEFORE DRILLING.
-IMPORTANT: IF YOUR WALLS ARE NOT SOLID LIKE BRICK OR STONE, YOU WILL REQUIRE SPECIALIST
FITTINGS (NOT SUPPLIED)
-Pre-drill small pilot hole on the back edge of the furniture top using a 2mm drill bit. Attach the other end of the
fixing strip to the back edge of the furniture top using the 15mm screw + washer and securely tighten.
-Place fixing strip against the wall and mark position for drilling hole.
-Drill hole in your wall to a depth of 30mm using a 6mm drill bit. If the surface of your wall is soft and crumbly, we
would advise you to use a 5mm drill bit for a tighter fit.
-Insert plug into hole with end flush to the wall surface.
-Attach fixing strip to the wall using the 25mm screw + washer and securely tighten.
D
B
J
I
I
I
I
L