COREONE WELDING CORECUT30i User manual
OPERATING MANUAL
(POWERSOURCE)
PLEASE READ AND UNDERSTAND THIS MANUAL CAREFULLY BEFORE THE INSTALLATION AND
OPERATION OF THIS EQUIPMENT
1YEAR Warranty
OPERATING MANUAL
CORECUT30i
CONTENTS
PAGE
2
6
Calirnia Proposition 65
WARRANTY
D
D
2
4
AIR PLASMA CUTTING TECHNOLOGY
11
6
Features
This model’s main functional features are
Double plastic panel
o
Delay o
Panel gauge display
Built-in air filter
o connector for Torch
Low frequency arc
oo
o
oo
fully CSA/CAN Compliant
110/230V Single Phase 30 Amp Plasma utter
Small, Lightweight and Portable
The new CORECUT Air Plasma machine is COREONE'S latest
offering in Inverter Technology. Small and extremely efficient, it
is one of the most portable single phase Inverter Cutting
Machines on the market today. The machine comes with
aAir-regulator, 1ft torchreturn lead,
starting consumable pack and an to understand operation
Manual Plus a o*o
ooo
ooo
1
YEAR
Warranty*
(POWER SOURCE)
RWPD- 0116-8
Cutting Nozzles
COR R-0110
Electrodes
COR C-0116
Retaining Cap
COR E-106
Swirl Ring
Buggy
COR C-2551
COR C2540
Stando guide
• DUAL VOLTAGE 110V ~ 230
• 1/4 INCH CUTTING CAPACITY ON MILD STEE
• ADJUSTABLE AIR FILTER REGULATO
• AIR FLOW PRESSURE - 65-75PS
• AIR FLOW RATE -6CF
• 35% @ 30AMP DUTY CYCL
• IP21S RATING FOR ENVIROMENTAL / SAFETY PROTECTION
• LOW FREQUENCY ARC STRIKING METHOD
•NANN1N
• EFFICIENCY -80%
• RATED INPUT POWER- 3.9-4.6KVA
• COOLING METHOD - FAN COOLED
• LIGHT WEIGHT - MACHINE ONLY WEIGHS 18 POUNDS
• COMPLIANT TO - CAN/CSA-E60974-1 / ANSI/IEC 60974-1
T
oo
o
: Steels, Stainless, Cast Iron, Bronze, Aluminum
Machine complete with TRF45-1Ft
Torch Code:COR30iLT
1
2
3
4
6
8
7
5
10
9
11
1213
14
15
12-Air hose
13-P.C.B
14-Regulator drain chamber
15-Air solonoid
connection
(1) Connect the Plasma rch to the machine. Insert the torch connection into the torch connection receptacle at
the front of the machine and screw up hand tight. If direct connect torch, the torch is already matched to
the machine.
Caution: Be careful not to bend the pins located inside the torch connector.
(2) Connect the earth lead to the output terminal of the machine and tighten.
(3) Connect the air supply to the air connection located at the rear of the machine.
Turn on the air supply
(4) Connect the machine to the correct power supply and switch on the machine using the on/o switch
located at the rear of the machine.
(5) Power light will go on.
(6) Set your Amperage
D
ial (4) ta
k
ing care that ma
x
amps is only used on the 23
0v
input power.
(7)
Simply place your outside guide onto your wor
k
and press the trigger, you will initiate your arc and start
cutting
9
1- Plasma torch connection
2- Overload light
3- Power light
4- Amperage adjustment
5- Earth Lead connection
115/230v
Power Adapter
___ Stand off
guide
_______________
____________________________
_____________________
Operating
Procedure:
Poor quality cut
Good quality cut
10
o
11
P
Operating Procedure & chniques r
PLASMA Cutting continued
...
-
°
12
J
1
r
•Piercing
I r
13
WARRANTY
z
RRANTY PERIOD
z
15
WARRANTY/ RETURNS/ EXCHANGES
PURCHASER'S REMEDIES:
MAKING A CLAIM
4
44
16
RRANTY EXCLUSIONS
MIG Welding Torches and Consumables to suit, such as:
TIG Welding Torches and Consumables to suit, such as:
PLASMA Cutting Torches and Consumables to suit, such as:
STRAIGHT LINE CUTTING MACHINES and Consumables to suit, such as:
REMEMBER TO RETAIN YOUR ORIGINAL INVOICE FOR PROOF OF PURCHASE.
17
18
C
OREONE
Welding
E
ngineered Welding Sol
u
tions
Cel:
e-mail:
+ 1 330-546-5917
in
f
CCut30i
Table of contents
Other COREONE WELDING Cutter manuals
