Cornelius 3030 AK 6 User manual

ICE/SOFT DRINK
POST-MIX DISPENSER
Model 3030 AK 6, 8 or 10
3030 AK 6, 8 or 10 PB
PRINTED IN U.S.A
IMI CORNELIUS INC; 1989-95
Part No. 91715
August 1995
Revision R3
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment

i91715
TABLE OF CONTENTS
Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY PRECAUTIONS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION INSTRUCTIONS 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GATE RESTRICTOR PLATE 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTMENT 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAILY (OR AS REQUIRED) 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEEKLY (OR AS REQUIRED) 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MONTHLY 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
START-UP AND OPERATING INSTRUCTIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING INSTRUCTIONS 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISPENSER 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COLD PLATE 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEVERAGE SYSTEM 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING GUIDE 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLOWN FUSE OR CIRCUIT BREAKER. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GATE DOES NOT OPEN. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GATE DOES NOT OPEN OR IS SLUGGISH. AGITATOR TURNS. 12. . . . . . . . . . .
GATE OPENS. AGITATOR DOES NOT TURN. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICE DISPENSES CONTINUOUSLY. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLUSHY ICE. WATER IN HOPPER. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEVERAGES DO NOT DISPENSE. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEVERAGES TOO SWEET. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEVERAGES NOT SWEET ENOUGH. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEVERAGES NOT COLD. 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL 3030 PARTS LIST 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIST OF FIGURES
FIGURE 1. GATE RESTRICTOR PLATE 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 2. MOUNTING TEMPLATE 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 3. BEVERAGE SYSTEM SCHEMATIC 5. . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 4. PLUMBING SCHEMATIC – MODEL 3030AK6, –6PB 6. . . . . . . . . . . . .
FIGURE 5. PLUMBING SCHEMATIC – MODEL 3030AK8, –8PB 7. . . . . . . . . . . . .
FIGURE 6. PLUMBING SCHEMATIC – MODEL 3030AK10, –10PB 8. . . . . . . . . .
FIGURE 7. WIRING DIAGRAM 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 8. MODEL 3030 SOLENOID ASSEMBLY – EXPLODED VIEW
AND PARTS LIST 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIST OF TABLES
TABLE 1. SPECIFICATIONS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manufactured Under One or More of the Following Patent Numbers: 3,211,336, 3,274,792,
3,393,839, 3,517,860, 3, 739,842, 4,215,803, 4,227,377, 4,300,359, 4,346,824
Canadian Patent Numbers 912,514 (10/72), 936,855 (11/73), 4,429,543, 4,921,149
Other Patents Pending

917151
SAFETY PRECAUTIONS
Always disconnect power to the dispenser before servicing or cleaning.
Never place hands inside of hopper or gate area without disconnecting power to the dispenser. Agitator rotation
occurs automatically when the dispenser is energized!
This ice dispenser has been specifically designed to provide protection against personal injury and eliminate
contamination of ice. To ensure continued protection and sanitation, observe the following:
ALWAYS be sure the removable lid is properly installed to prevent unautho-
rized access to the hopper interior and possible contamination of ice.
ALWAYS be sure the upper and lower front panels are securely fastened.
ALWAYS keep area around the dispenser clean of ice cubes.
CAUTION: Dispenser cannot be used with crushed or flaked ice.
Use of bagged ice, which has frozen into large chunks, can void warranty. The dispenser
agitator is not designed to be an ice crusher. Use of large chunks of ice which “jam up”
inside the hopper will cause failure of the agitator motor and damage to the hopper. If bagged ice
is used, it must be carefully and completely broken into small, cube-size pieces before filling into
the dispenser hopper.
GENERAL DESCRIPTION
The 3030 series of ice dispensers solve ice and beverage service needs in the sanitary, space saving, economi-
cal way. Designed to be manually filled with ice from any remote ice making source, these dispensers will dis-
pense cubes (up to 1-1/4I2 in size), cubelets and hard-chipped or cracked ice; and in addition, several flavors
of post-mix beverages.
The sink can be easily and quickly removed. The unit must never be lifted or moved by the sink.
Dispensers include faucets and cold plates and are designed to be supplied directly from syrup tanks and car-
bonator, with no additional cooling required.
Table 1. Specifications
Model: 3030AK6, 3030AK6PB* 3030AK8, 3030AK8PB* 3030AK10, 3030AK10PB *
Ice Storage: 220 lbs. 220 lbs. 220 lbs.
Maximum Number of Faucets
Available: 6 8 10
Built-in Cold Plate: Yes Yes Yes
Electrical: 120/1/60 120/1/60 120/1/60
Dimensions: 30IW x 30ID x 36IH 30IW x 30ID x 36IH 30IW x 30ID x 36IH
*Push-Button

291715
INSTALLATION INSTRUCTIONS
1. The ice dispenser must be sealed to the counter. The template drawings (See Figure 2) indicate openings
which must be cut in the counter. Locate the desired position for the dispenser, then mark the outline di-
mensions and cut out locations using the template drawing. Cut openings in the counter.
Apply a continuous bead of NSF International (NSF) approved silastic sealant (DOW 732 or equal) approxi-
mately 1/4Iinside of the unit outline dimensions and around all openings. Then position the unit on the
counter within the outline dimensions. All excess sealant must be wiped away immediately. The sink is
shipped loose and is not to be sealed. This is needed for installation of the beverage system and
for service.
2. Beverage connections are made in the front of the unit. With the lower panel removed, use the plumbing
schematic (See Figure 4) or schematic on rear of panel to determine syrup and water connections.
3. Carefully pull the beverage tubes, drain line and power cord through the large openings in the bottom
of the unit.
4. Connect the drain tube to an open drain. If additional piping is required, it must be 3/4IIPS (or equal) and
must pitch downward away from the unit for proper drainage.
5. Connect the beverage system product lines as indicated in Figure 4. This work should be done by a quali-
fied service person.
6. Clean the hopper interior. (See CLEANING INSTRUCTIONS on pages 9 - 10 ).
7. Connect the power cord to a 115 volt, 60 cycle, 3-wire grounded receptacle. All electrical wiring must con-
form to national and local electrical codes.
GATE RESTRICTOR PLATE
CAUTION: Disconnect power to dispenser before installing, removing or
adjusting restrictor.
INSTALL PLATE ON
STUDS AS SHOWN
FIGURE 1. GATE RESTRICTOR PLATE

917153
ADJUSTMENT
This dispenser is provided with a gate restrictor plate, installed in it’s highest position. This plate adjusts the rate
of ice flow from the dispenser. In applications using buckets, carafes or other large containers, the plate may be
removed entirely for maximum ice flow. For glasses and cups, the plate may be adjusted downward to reduce
the flow of ice. The best position depends on the type of ice being used and the size container and must be
found by trial and error. Adjustment is made by loosening the upper two ice chute retaining nuts, sliding the re-
strictor plate to the desired position and re-tightening the nuts.
If the dispenser fails to dispense the ice when operated, check that the hopper has ice in it and that power is
being supplied to the unit. If the problem persists, check the following.
1. Determine if the agitator is rotating (check for the sound of ice movement in the hopper).
2. Observe whether the gate is opening.

491715
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
14 I
OPENING
30
8.625
6.5I17I
OPENING
30I
FRONT
0.500
(4) PLCS.
NOTE: Shaded area indicates opening in counter required
for utilities and beverage tubing.
FIGURE 2. MOUNTING TEMPLATE
I
*27.750I
*1.125I
*1.125I
*20.766I

591715
FIGURE 3. BEVERAGE SYSTEM SCHEMATIC
NOTE: REFER TO AP-
PROPRIATE PLUMBING
SCHEMATIC FOR
HOOKUP’S
REGULATOR
1
2
3
4
5
6
7
8
9
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
10
S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
ITEMS OUTSIDE OF THE BROKEN
LINES ARE NOT INCLUDED WITH
THE UNIT.
COLD PLATE
SUPPLY
FAUCETS
ROOT BEER
PSIG
15 –50 PSIG
REGULATORS
CO2TANK 2
TANKS
FILTER
CARBONATOR

691715
S3S2S1 S4 S5 S6
SYRUP
INLETS
SYRUP
INLETS
NOTE: 1) TO SERVICE COLD PLATE INLET FITTINGS, SINK HAS TO BE REMOVED. TO REMOVE, DISCON NECT SINK DRAIN
CONNECTIONS, THEN LIFT TWO (2) SIDE MOUNTING PINS AND PULL SINK FORWARD. REVERSE TO RECONNECT.
2) MAKE SURE ALL DRAIN CONNECTIONS ARE PROPERLY POSITIONED FOR DRAINING AFTER SERVICE, BEFORE
PANELS ARE INSTALLED.
3) DO NOT USE INLETS.
W
6
5
4
PLUMBING SCHEMATIC
3
1
WATER INLETS
2
S6S5S4
W
S3S2S1
W
4,5,6
COLD PLATE
3
1,2
MANIFOLDS
BEHIND
VALVES
MAY BE CARBONATED
OR NONCARBONATED
W
FAUCETS
FIGURE 4. PLUMBING SCHEMATIC –MODEL 3030AK6, –6PB

791715
3
1,2
SYRUP INLETS SYRUP INLETS
NOTE: 1) TO SERVICE COLDPLATE INLET FITTINGS, SINK HAS TO BE REMOVED. TO REMOVE, DISCONNECT SINK
DRAIN CONNECTIONS, THEN LIFT TWO (2) SIDE MOUNTING PINS AND PULL SINK FORWARD. REVERSE
TO RECONNECT.
2) MAKE SURE ALL DRAIN CONNECTIONS ARE PROPERLY POSITIONED FOR DRAINING AFTER SERVICE,
BEFORE PANELS ARE INSTALLED.
PLUMBING SCHEMATIC
S4S3
S1
WATER INLETS
S5
S2 S3
W
S5S4
S1
S6
S2
S7 S8
W
S6
FAUCETS
6,7,8
W
S7
MANIFOLDS
BEHIND VALVES
S8
W
COLD PLATE
MAY BE CARBONATED
OR NONCARBONATED
15
26 8
7
4
3,4
5
FIGURE 5. PLUMBING SCHEMATIC –MODEL 3030AK8, –8PB

891715
SYRUP INLETS
FAUCETS
SYRUP INLETS
NOTE: 1) TO SERVICE COLD PLATE INLET FITTINGS, SINK HAS TO BE REMOVED. TO REMOVE, DISCONNECT SINK DRAIN
CONNECTIONS, THEN LIFT TWO (2) SIDE MOUNTING PINS AND PULL SINK FORWARD. REVERSE T0 RECONNECT.
2) MAKE SURE ALL DRAIN CONNECTIONS ARE PROPERLY POSITIONED FOR DRAINING AFTER SERVICE, BEFORE
PANELS ARE INSTALLED.
MAY BE
CARBONATED
OR PLAIN WATER
10
9
87
43
1
WATER INLETS
1,5,6,7,
8,9,10
2
S10S9S8S7S64S5S4S3S2S1 3 2
6
5
COLD PLATE
PLUMBING SCHEMATIC
FIGURE 6. PLUMBING SCHEMATIC –MODEL 3030AK10, –10PB

991715
MAINTENANCE
The following dispenser maintenance should be performed at the intervals indicated:
DAILY (or as required)
Remove foreign material from the vending area sink to prevent drain blockage.
WEEKLY (or as required)
Clean vending area. Check for proper water drainage from the vending area sink.
MONTHLY
Clean and sanitize the hopper interior (see CLEANING INSTRUCTIONS).
START-UP AND OPERATING INSTRUCTIONS
Fill the hopper with ice. With a built-in cold plate, dispense several large cups of ice (approximately one {1} min-
ute total dispensing time) to allow ice to fill the cold plate. Add ice to the hopper as necessary to refill, then re-
place the lid. Allow 10 to 15 minutes for the cold plate to cool down. Repeat this procedure whenever the dis-
penser has been standing overnight or other long periods without ice use. Start up the beverage system and
adjust faucets to the proper brix. Contact your local syrup distributor for complete information on the beverage
system.
In normal operation, pushing the ice dispenser lever will cause ice to flow from the ice chute. Ice flow will contin-
ue until the lever is released. Pushing the lever on any faucet will provide beverage of the appropriate flavor.
NOTE: Use caution to avoid spilling when filling dispenser. immediately clean up any spilled ice from
filling or operating the unit. To prevent contamination of ice, the lid must be installed on the
unit at all times.

1091715
CLEANING INSTRUCTIONS
WARNING: DISCONNECT POWER BEFORE CLEANING! Do not use metal scrapers, sharp
objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage
may result. Do not use solvents or other cleaning agents, as they may attack the
plastic material.
DISPENSER
1. Clean the ice storage hopper at least once a month.
2. Remove the center screw on the agitator disk and lift off the agitator and the agitator disk assembly. Wash
and rinse them thoroughly.
3. Wash down the inside of the hopper and top cover with a mild detergent solution and rinse thoroughly to
remove all traces of detergent.
4. Replace the agitator.
5. Sanitize the inside of the hopper and agitator with a solution of 1 ounce of household bleach in 2 gallons of
water. (200 PPM)
6. Remove ice chute cover as follows:
A. Flex sides outward to disengage lower pins.
B. Lift ice chute cover to disengage upper pins.
C. Lower ice chute cover down out of unit. NOTE: it may be helpful to twist cover slightly.
7. Clean the inside of the ice chute and ice chute cover with a mild detergent solution and rinse thoroughly to
remove all traces of detergent.
8. Reverse steps above to reassemble ice chute.
9. Sanitize as described in Step 5.
COLD PLATE
1. Remove splash panel and merchandiser.
2. Remove bottom two (2) screws on the ice chute and loosen the top two (2) screws. You do not have to re-
move the ice chute. (During reassembly, make sure the ice gate restrictor is relocated to its
correct position.)
3. Remove the screw, hold the beverage faucet panel and bring forward.
4. Remove the tape holding the lower cold plate cover to the top cold plate cover.
5. Lift the lower cold plate cover up into the top cover.
6. Remove any debris from the drain trough and spring. Check that the drain hole is not clogged.
7. Wash down the inside of the cold plate, tray and cover with a mild detergent solution and rinse. A small,
long-handled brush will be found helpful in reaching the corners.
8. Slide the cover forward, taking care that it is securely positioned on the cold plate.

11 91715
9. Reassemble.
BEVERAGE SYSTEM
1. Remove faucet spouts, wash in mild detergent, rinse and replace.
2. Disconnect electrical power to the carbonator. Shut off the water supply and close the CO2regulator to the
carbonator.
3. Disconnect the syrup tanks from the system.
4. Energize the beverage faucets to purge the remaining soda in the system.
5. Use a clean 5 gallon tank for each of the following.
A. Cleaning tank - Fill with hot (120°- 140°) potable water.
B. Sanitation Tank - Fill with a chlorine sanitizing solution to the strength of 1 ounce of household
bleach (sodium hypochlorite) to 2 gallons of cold (ambient) potable water (200 PPM).
6. Repeat the following procedure on each of the units’syrup product lines:
A. Connect the cleaning tank to the syrup line to be sanitized and to the CO2system.
B. Energize the beverage faucet until the liquid dispensed is free of any syrup.
C. Disconnect the cleaning tank and hookup the sanitizing tank to the syrup line and CO2system.
D. Energize the beverage faucet until the chlorine sanitizing solution is dispensed through the faucet.
Flush at least 2 cups of liquid to ensure that the sanitizing solution has filled the entire length of the
syrup lines.
E. Disconnect the sanitizing tank. Hookup the product tank to the syrup line and to the CO2system.
F. Energize the faucet to flush the sanitizing solution from the syrup line and faucet. Continue to draw on
the faucet until only syrup is dispensed.
7. Repeat Step 2 in reverse order to turn on the carbonator. Dispense at least 1 cup of beverage from each
faucet. Check taste. Continue to flush if needed, to obtain a satisfactory tasting drink.

1291715
TROUBLESHOOTING GUIDE
Should your unit fail to operate properly, check that there is power to the unit and that the hopper contains ice.
If the unit does not dispense, check the following chart under the appropriate symptoms to aid in locating
the defect.
Trouble Probable Cause
BLOWN FUSE OR CIRCUIT BREAKER. A. Short circuit in wiring.
B. Defective gate solenoid.
C. Defective agitator motor.
GATE DOES NOT OPEN. A. No power.
B. Bent depressor plate (does not actuate switch).
C. Defective dispensing switch.
D. Blown/defective fuse or jammed gate solenoid.
GATE DOES NOT OPEN OR IS SLUGGISH.
AGITATOR TURNS.
A. Defective gate solenoid.
B. Weak gate spring.
C. Excessive pressure against gate slide.
GATE OPENS. AGITATOR DOES NOT TURN. A. Ice solidified in hopper.
B. Defective agitator motor.
C. Defective capacitor.
D. Defective agitation timer.
ICE DISPENSES CONTINUOUSLY. A. Stuck or bent depressor plate (does not release
switch).
B. Defective dispensing switch.
C. Improper switch installation.
SLUSHY ICE. WATER IN HOPPER. A. Blocked drain.
B. Unit not level.
C. Poor ice quality due to water quality or icemaker
problems.
D. Improper use of flaked ice.
BEVERAGES DO NOT DISPENSE. A. No 24 volt power to faucets.
B. No CO2pressure.
BEVERAGES TOO SWEET. A. Carbonator not working.
B. No CO2pressure in carbonator.
C. Faucet brix requires adjusting.
BEVERAGES NOT SWEET ENOUGH. A. Empty syrup tank.
B. Faucet brix requires adjusting.
BEVERAGES NOT COLD. A. Unit standing with no ice in hopper - no ice in
cold plate.
Contact your local syrup or beverage equipment distributor for additional information and troubleshooting of your
beverage system.

13 91715
L
N
N
L
3
24
YEL
PRP
STARTING
RELAY
BLUE
24 V.
N
L
BLK
WHT
RED
STARTER
LIGHT
BALLAST
CAPACITOR
BLK
WHT N
L
RED
RED
WHT
YEL AGITATOR
MOTOR RELAY
BLUE
BRN
LIGHTED DIS-
PLAY
OPTION
MOTOR
HEATER
24 V.
SERVICE INFORMATION
ELECTRIC SHOCK HAZARD. DISCONNECT
POWER BEFORE SERVICING UNIT.
DANGER!
WHEN REPLACING SOLENOID,
ADJUST TO 7/8 AS SHOWN
BEFORE TIGHTENING
MOUNTING SCREWS.
STANDARD SOLENOID
ADJUSTMENT
TERMINAL
BOARD
GRN
N
L
DISPENSE
SWITCH
BLK
YEL
WHT
1–1/4 AMP TIME
DELAY FUSE
WHT
GATE
SOLENOID
BLK
AGITATOR
MOTOR
WHT
AGITATION TIMER
BLK
BLK
BEVERAGE SYSTEM
KEY
SWITCH
OPTION BEVERAGE
FAUCET
(TYPICAL)
TRANSFORMERS
BLK
WHT
ICE LEVEL
SIGNAL OPTION WHT
LIGHTT’STAT
NO
7/8
FIGURE 7. WIRING DIAGRAM

1491715
123
4
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
19
20
21
22
22
22
FIGURE 8. MODEL 3030 SOLENOID ASSEMBLY –EXPLODED VIEW AND PARTS LIST
Index
No. Part No. Qty. Name
1 21493 1 Solenoid Mounting Plate
2# 31551 1 Solenoid Service Kit
3 70171 2 8–32 x 3/8 Phil Tr HD Screws
4 70121 2 No. 8 Lockwasher
5 50752 3 Isolator
6* 50789 2 Bumper Assembly
7* 70423 1 Cotter Pin
8* 10080 1 Gate Lift Rod
9 10081 1 Gate Lift Rod Bushing
10 50754 1 Gate Arm Bearing
11 21492 1 Gate Lift Arm
12 70043 1 Flatwasher
13* 70422 1 Spring
14 70263 1 1/4-20 x 3/4 Hex Hd Screw
15 70048 1 1/4 Lockwasher
16 70066 1 1/4 Flatwasher
17 10077 1 Pivot Bearing
18 30227 1 1/4 Quick Connect Tab
19 50305 –– Lubricant
20* 21592 1 Solenoid Linkage Pin
21* 70433 2 Retainer Ring
22 51088 –– Loctite
––* 70438 –– Rebuilding Kit
NOTE: * Parts supplied with rebuilding kit.
# 31551 solenoid supplied with items 20 & 21.

15 91715
MODEL 3030 PARTS LIST
Item
No. Part No. Name
1 21491 Gate Slide
2 21515 Depressor, Cup Activated
3 22644 Depressor Retainer (for 21515)
4 27126 Depressor Push Lever
5 27107 Depressor Retainer (for 27126)
6 28075 Agitator
7 02070 Dispense Switch Kit
8 31007 Switch Boot
9 70847 Switch Spacer
10 52239 Foam Shield
11 32939 Agitator Motor
12 51101 Motor Shaft Seal
13 52205 Motor Gasket
14 52152 Lid
15 52191 Sink
16 53015 Ice Chute Back Section
53016 Ice Chute Cover
17 51891 Gate Gasket
18 70918 Sink Grill
19 90295 Cleaning Label
20 91680 Wiring Diagram
21 31093 Solenoid Assembly
22 30794 Agitator Motor Heater
23 31763 Agitation Timer
24 31406 Fuse, Gate Solenoid
25 31620 Fluorescent Starter
26 31375 Relay, Mercury
27 31621 Ballast
28 33162 Relay, Agitator Motor Starting
29 33160 Capacitor, Agittor Motor

16
91715 SD 99-1
IMI CORNELIUS INC.
One Cornelius Place
Anoka, MN. 55303–6234
Telephone [phone]
Facsimile (612) 422–3232
WARRANTY
IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and workmanship un-
der normal use and service. For a copy of the warranty applicable to your Cornelius product, in your country,
please write, fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number
and the date of purchase.
IMI Cornelius Offices
AUSTRALIA DP. O. 210, DRIVERWOOD, DNSW 2210, AUSTRALIA D(61) 2533 3122 DFAX (61) 2534 2166
AUSTRIA DAM LANGEN FELDE 32 DA-1222 DVIENNA, AUSTRIA D(43) 1233 520 DFAX (43) 1-2335-2930
BELGIUM DBOSKAPELLEI 122 DB-2930 BRAASCHAAT, BELGIUM D(32) 3664 0552 DFAX (32) 3665 2307
BRAZIL DRUA ITAOCARA 97 DTOMAS COELHO DRIO DE JANEIRO, BRAZIL D(55) 21 591 7150 DFAX (55) 21 593 1829
ENGLAND DTYTHING ROAD ALCESTER DWARWICKSHIRE, B49 6EU, ENGLAND D(44) 789 763 101 DFAX (44) 789 763 644
FRANCE D71 ROUTE DE ST. DENIS DF-95170 DEUIL LA BARRE DPARIS, FRANCE D(33) 134 28 6200 DFAX (33) 134 28 6201
GERMANY DCARL LEVERKUS STRASSE 15 DD-4018 LANGENFELD, WEST GERMANY D(49) 2173 7930 DFAX (49) 2173 77 438
GREECE D488 MESSOGION AVENUE DAGIA PARAS KEVI D153 42 DATHENS, GREECE D(30) 1600 1073 DFAX (30) 1601 2491
HONG KONG D1104 TAIKOTSUI CENTRE D11-15 KOK CHEUNG ST DTAIKOKTSUE, HONG KONG D(852) 789 9882 DFAX [phone]
ITALY DVIA PELLIZZARI 11 D1-20059 DVIMARCATE, ITALY D(39) 39 608 0817 DFAX (39) 39 608 0814
NEW ZEALAND D20 LANSFORD CRES. DP. O. BOX 19-044 AVONDALE DAUCKLAND 7, NEW ZEALAND D(64) 98200 357 DFAX (64) 98200 361
SINGAPORE D16 TUAS STREET DSINGAPORE 2263 D(65) 862 5542 DFAX (65) 862 5604
SPAIN DPOLIGONO INDUSTRAIL DRIERA DEL FONOLLAR DE-08830 SANT BOI DE LLOBREGAT DBARCELONA, SPAIN D(34) 3640 2839 DFAX (34) 3654 3379
USA DONE CORNELIUS PLACE DANOKA, MINNESOTA D(612) 421-6120 DFAX [phone]

One Cornelius Place
Anoka, Minnesota 55303-6234
[phone]
[phone]
Corporate Headquarters:
IMI CORNELIUS INC.