Cornelius VANGUARD 245 User manual

October 28, 1997
EIMI Cornelius Inc; 1997 569030007
IMI CORNELIUS INC.
One Cornelius Place
Anoka, MN. 55303-6234
Telephone [phone]
Facsimile (612) 422–3232
ADDENDUM TO INSTALLATION/SERVICE MANUAL
IMI CORNELIUS INSTALLATION/SERVICE MANUAL (P/N 569000203)
FOR
VANGUARD 245 POST-MIX OVERCOUNTER DISPENSER
(Mc DONALD’SRAPPLICATIONS)
The purpose of this Addendum is to document additional information about the Vanguard 245 Post-Mix Overcounter
Dispenser (P/N 497306660WS) not documented in manual (P/N 569000203) provided with this Dispenser. This Dis-
penser is equipped with a plain water dispensing spout located between No. 5 and No. 6 dispensing valves that when
activated, will dispense chilled plain water.
NOTE: A CO2“OUT” Light Kit (P/N 1983) and a Dispenser Leg Kit (P/N 560000126) are available for all of
the Vanguard 245 Dispensers.
INSTALLATION
INSTALLING DISPENSER ON COUNTERTOP
Select location and install Dispenser on countertop as instructed in manual provided with the Dispenser.
CONNECTING PLAIN WATER LINE TO DISPENSER PLAIN WATER DISPENSING
SYSTEM
(see Figure 1)
Plain water connected to the Dispenser plain water solenoid valve, located on top of the refrigeration deck, pro-
vides chilled plain water to be dispensed from the plain water dispensing spout. Proceed as follows to connect
plain water to the plain water solenoid valve.
1. Remove Dispenser hood for access to the plain water solenoid valve on top of the refrigeration deck (see
Figure 1).
2. Route plain water line from filtered plain water source up to the Dispenser.
3. Route plain water line up under Dispenser, up behind Dispenser front access panel, and on to plain water
solenoid valve on top of the refrigeration deck.
4. Connect plain water line to inlet of the plain water solenoid valve.
COMPLETING INSTALLATION OF THE DISPENSER
IMPORTANT: Before installing Dispenser front access panel, make sure the two-wire electrical wiring
harness with spade clip terminals on it’s end (intended for connection to the push-button plain water
dispense switch on the drip tray support) is hanging down out bottom of the Dispenser. This wiring
harness must be connected to the plain water dispense switch before installing the drip tray in the drip
tray support.
Complete installation of Dispenser as instructed in manual provided with your Dispenser.

2569030007
OPERATION
Place cup or glass under plain water spout between No. 5 and No. 6 dispensing valves. Press plain water dis-
pense switch on side of the drip tray support until cup or glass is full of chilled water, then release dispense
switch.
SCREW
HOOD
PLAIN WATER
SOLENOID VALVE
FRONT ACCESS
PANEL
SCREW
CUP REST
DRIP TRAY
TWO-WIRE ELECTRICAL
WIRING HARNESS
PLAIN WATER
DISPENSE SWITCH
DRIP TRAY SUPPORT
WATER DISPENSING
SPOUT
FIGURE 1. INSTALLATION

5690300073
CO2WATER 1
SYRUP 1
CO2WATER 2
SYRUP 2
CO2/PLAIN WATER
SYRUP 4
CO2WATER 4-5
SYRUP 5
SYRUP 6
DUAL CARB WATER
COOLING COILS (5)
SYRUP COOLING
COIL (6)
PLAIN WATER
COOLING COIL STILL
(NON-CARB)
OR CARBDRINK
DISPENSING
VALVE (6)
1
2
3
4
5
6
SYRUP 3
CO2WATER 6
CARB DRINK
CARB DRINK
CARB DRINK
CARB DRINK
CARB DRINK
PLAIN WATER
PLAIN WATER
COOLING COIL
SOLENOID
VALVE
WATER SPOUT
FIGURE 2. FLOW DIAGRAM (DISPENSER P/N 497306660WS)

4
569030007
FIGURE 3. WIRING DIAGRAM (DISPENSER P/N 497306660WS)
PUSH BUTTON
SWITCH
SOLENOID
UNIT WITH WATER
SPOUT ONLY