Cornerstone LANCASTER FARMHOUSE 933-3333 User manual

HO Structure Kit
933-3333
LANCASTER FARMHOUSE
1. Begin assembly by installing
window frames (12, 14) to the
outside of wall sections ( 2, 3, 4, 6)
as shown. Apply glass (13, 15) to
frames from behind.
3. Wall 7 will become the “front” of
the model. Wall 8, is the “rear” of
the model. Install all frames (10,
12, 16, 18), and clear glass (11, 13, 17,
19).
2. Add door (18) to outside of wall
(9), and then clear glass (19) to back
side of door.
12
314
13
15
13
9
7
11
13
13
11
10
17
16
2
6
4
12
18
19
18
19
12
8
12
8x 8x
2x
2x
2x
© 2012 Wm. K. Walthers, Inc., Milwaukee, WI 53218 waltherscornerstone.com I-933-3333
Thanks for purchasing this Cornerstone kit! All parts are styrene, so use compatible glue and paint. For more ideas to detail
your scene, ask your dealer, visit our Web-site waltherscornerstone.com or see the latest Walthers HO Scale Model Railroad
Reference Book.

4. With each wall sub assembly done, apply
walls 2, 3, 4, 5, 6, 7, 8, 9 to base 1. Start with
wall 2 first, as this wall has an alignment tab to
aid positioning. Apply the remaining walls in
clockwise order.
6. Repeat this procedure for roof
parts (34, 36, 37) and soffit detail
(38, 40, & 41).
5A. (view of assembled roof for reference)
Parts 35 & 39
Assembled
5. Making sure it’s centered properly, glue
soffit detail (part 39) to the underside of
roof section 35.
39
4
2
7
41
38
9
61
5
3
8
36
37
34
35
40

7. Apply roof assembly (35) to
model first, then assembly (34) next.
Sections 36 and 37 are then added.
Roof Ridges 42 and 43, are placed
between each assembly as shown.
8. Add long and short railings (21, 22)
to porch deck (20). Glue porch ceiling
(25) to underside of roof (26), and add
to the top of the railings. Be sure stair
treads (24) are centered when glued to
steps (23).
8A. Add assembly from step 8 to front of model as shown.
9. Back porch consists of items 27, 28, 29, 30. DO NOT
GLUE ROOF (part 30) at this time! It is recommended to
start by adding the Back Porch Roof Support (29) to porch
deck 27 - make sure part 29 is straight. Add stairs (28)
next.
9A. When assembly from step 9 is dry, add it to the back
of the model. Glue roof (30) to top of locating ridge on
wall, and top of roof support 29.
42
34
26
25
21
23
29
27
30
36
43
35
37
22
20
24
28

12. Chimney halves (50, 51) are glued
together, and finished with cap (52).
Add this to the recess on the front
roof. Down spouts, (33, 47) are glued
to the walls as indicated. Important
Note: Part 47 should be parallel with
the edge of the wall. Top of part 47,
should be flush against the bottom
of the gutters for proper appearance.
Finish by adding cellar doors (53) in
position shown.
11. Repeat the process for the remaining
gutter and trim parts, as shown.
10. Front gutter (44) and
eave trim (48, 49) are added
next. Gutter fits up under
soffit detail. Please note the
proper orientation of parts
48 and 49 - the notches at
the top of the part face each
other to clear the roof ridge.
46
47
33
47
52
50
51
48
48
31
32
47
53
49
49
45
44
2x
2x