Cortelco 2933 Setup guide

OWNER’S INSTRUCTION
MANUAL
Model 2933
Telephone

2
Table of Contents
SAFETY INSTRUCTIONS.........................................................................3
FEATURES .............................................................................................4
INSTALLATION.......................................................................................5
OPERATION ..........................................................................................6
MEMORY PROGRAMMING ..................................................................7
MEMORY DIALING................................................................................7
MESSAGE WAITING INDICATOR ...........................................................7
LOCATION OF CONTROLS .....................................................................8
TELEPHONE REPAIR..............................................................................9
FCC INFORMATION.............................................................................10
LIMITED WARRANTY ..........................................................................12

3
PLEASE READ BEFORE INSTALLING AND USING YOUR
NEW TELEPHONE EQUIPMENT.
IMPORTANT SAFETY INSTRUCTIONS
1. Always follow basic safety precauons when using your telephone
equipment to reduce the risk of re, electrical shock, and injury.
2. Read and understand all instrucons in this manual.
3. Read all warnings and follow all instrucons marked on the product.
4. Unplug this product from the wall outlet before cleaning. Use a damp
cloth for cleaning. Do not use liquid or aerosol cleaners.
5. Do not use this equipment near water. For example, do not use near a
bathtub, wash bowl, kitchen sink, laundry tub, swimming pool, or in a
wet basement.
6. Do not place this product on an unstable cart or stand. The product
may fall causing serious damage to the product.
7. Do not place any objects on the telephone line cord. Do not locate the
telephone where the line cords will be walked on.
8. Do not block or cover venlaon slots and openings in the top of the
telephone. The openings should never be blocked by placing a book or
paper on top of the unit. The unit should never be placed near or over a
radiator or heat register.
9. Never spill liquid on the telephone or push objects of any kind through
venlaon slots. Liquid or objects may touch dangerous voltage points
or short out parts that could result in a risk of re or electrical shock.
10. Do not disassemble this product. Opening or removing covers may ex-
pose you to dangerous voltages or other risks. Incorrect reassembly can
cause electrical shock when the product is subsequently used.
11. Avoid using a telephone during a thunderstorm. There may be a re-
mote risk of electrical shock from lightning.
12. Do not use a telephone to report a gas leak in the vicinity of the leak.
13. Unplug the telephone from the wall outlet and refer servicing to quali-
ed service personnel under the following condions:
 When the line cord is frayed or plugs damaged.
 If liquid has been spilled into the telephone.

4
 If the telephone has been exposed to rain or water.
 If the telephone does not operate properly by following the operang
instrucons. (Adjust only those controls covered by the operang instruc-
ons. Improper adjustment of other controls may result in damage and
will oen require extensive work by a qualied technician to restore the
product to normal operaon.)
 If the telephone has been dropped or the housing damaged.
 If the telephone exhibits disnct change in performance.
FEATURES
 Six One-Touch Memories
 Ten Two-Touch Memories
 Last Number Redial
 Flash
 Mute
 Pause
 Pulse or Tone Dialing
 Handset Volume Control (HI/LO)
 Ringer Volume Control (HI/MID/LO)
 Message Waing Indicator

5
INSTALLATION
CHECK THE CONTENTS OF THE BOX
Box should contain
 Handset with handset cord and phone base
 Telephone line cord (9 feet long)
 Telephone line cord (4 inches long)
 Desk Stand
 User’s manual
INSTALL THE TELEPHONE
 Plug one end of the modular line cord into the line jack on the boom of
the phone. Use the short line cord for wall mounng and the long line
cord for desk mounng.
 Plug the other end of the cord into the telephone line jack.
 Plug one end of the coiled cord into the telephone handset
 Plug the other end of the coiled cord into the handset jack on the le side
of the phone.
 Snap the desk stand onto the boom of the telephone if it is not wall
mounted.
 Place the telephone on a at surface or mount it on a wall jack.
DIAL MODE
 If your telephone line accepts tone dialing, set the Pulse /Tone switch to
the Tone posion. The switch is located on the back of the telephone.
The default posion is Tone dialing.
 If your telephone line requires pulse dialing, set the Pulse /Tone switch to
the Pulse posion. While in Pulse mode, pressing the * key will switch to
Tone mode unl the call ends.

6
OPERATION
RECEIVING A PHONE CALL
 Be sure the ringer switch is set to the desired posion.
 When the phone rings, li the handset and talk to the other party
PLACING A PHONE CALL
 Li the handset and wait for a dial tone.
 Dial the telephone number you wish to call.
REDIAL
 Li the handset.
 Press the RD/P buon. The last number called will automacally be
redialed.
FLASH
The FLASH funcon provides a line break signal for accessing PBX services or
for use of Call Waing.
PAUSE
The PAUSE buon will insert a 3.6 second pause during dialing. This feature is
used with memory dialing.
MUTE
Press the MUTE buon to speak without being heard by the caller. Press
MUTE once to acvate this feature. Press MUTE again to deacvate.
HANDSET VOLUME
The handset volume switch is located on the back of the telephone. Adjust
the handset volume by sliding the switch to the HI or LO posion.
RINGER VOLUME
The ringer volume switch is located on the back of the telephone. Adjust the
ringer volume by sliding the switch to the HI, MID, or LO posion.

7
MEMORY PROGRAMMING
ONE TOUCH MEMORY
 Li the handset.
 Press and hold the *STORE key unl a tone is heard.
 Dial the number to be stored.
 Press the Memory key (M1-M6) to store the number.
TWO TOUCH MEMORY
 Li the handset.
 Press and hold the *STORE key unl a tone is heard.
 Dial the number to be stored.
 Press the MEMORY key.
 Press a numeric key (0—9) to store the number.
MEMORY DIALING
ONE TOUCH MEMORY
 Li the handset.
 Press the Memory key (M1-M6) to dial the number.
TWO TOUCH MEMORY
 Li the handset.
 Press the MEMORY key.
 Press a numeric key (0—9) to dial the number.
MESSAGE WAITING INDICATOR
The message waing indicator is compable with 90V (neon) message waing
signaling. The indicator will ash when a message is present.

8
LOCATION OF CONTROLS

9
TELEPHONE REPAIR
DO NOT ATTEMPT TO REPAIR THIS PRODUCT YOURSELF. Telephones manu-
factured by CORTELCO must be returned to us for repair. You can return your
telephone to CORTELCO for repair or replacement in accordance with our
LIMITED WARRANTY.
CORTELCO warrants THIS PRODUCT against defects in material and workman-
ship in accordance with our LIMITED WARRANTY. If your telephone is re-
turned for repair, include a copy of your sales receipt containing the date-of-
purchase. DO NOT INCLUDE THE ORIGINAL SALES RECEIPT. If date-of-
purchase is not included, the factory date printed on the label on the boom
of your telephone will be used as the date-of-purchase. The factory date al-
lows six months for distribuon and sale of this product.
If you return your telephone for repair, the warranty period is not extended.
The original date-of-purchase connues to apply to your warranty.
We will repair this product for a nominal fee aer the LIMITED WARRANTY
has expired if you send it to us complete and undamaged. The repaired unit
will be shipped to you C.O.D., freight collect.
If you are returning a unit to us for repair, package it carefully, preferably in
the original carton. Be sure to include your return address, a copy of the sales
receipt showing date-of-purchase, and a note describing the problem. Ship-
ping must be prepaid. If the telephone is in warranty, it will be repaired or
replaced, at our opon, at no cost to you, and it will be returned shipping
prepaid.
Ship your telephone (shipping prepaid) to:
CORTELCO REPAIR CENTER
1703 SAWYER ROAD
CORINTH, MS 38834

10
FCC INFORMATION
This equipment complies with Part 68 of the FCC rules. On the boom of this
equipment is a label that contains, among other informaon, a product iden-
er. If requested, this number must be provided to the telephone company.
This single line equipment connects to the telephone network via a RJ11 plug
and jack. The plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone cord
and modular plug is provided with this product. It is designed to be connected
to a compable modular jack that is also compliant.
The Ringer Equivalence Number (REN) is used to determine the number of
devices that may be connected to a telephone line. Excessive RENs on a tele-
phone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed ve (5.0). To
be certain of the number of devices that may be connected to a line, as deter-
mined by the total RENs, contact the local telephone company. The REN for
this product is part of the product idener.
If this equipment causes harm to the telephone network, the telephone com-
pany will nofy you in advance that temporary disconnuance of service may
be required. But if advance noce isn't praccal, the telephone company will
nofy the customer as soon as possible. Also, you will be advised of your right
to le a complaint with the FCC if you believe it is necessary. The telephone
company may make changes in its facilies, equipment, operaons or proce-
dures that could aect the operaon of the equipment. If this happens the
telephone company will provide advance noce in order for you to make nec-
essary modicaons to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty infor-
maon, please contact CORTELCO, Inc., [phone]. If the equipment is
causing harm to the telephone network, the telephone company may request
that you disconnect the equipment unl the problem is resolved.