Costway BC10062 User manual

Please give us a chance to make it right and do better !
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP !
Contact Us !
Do NOT return this item.
Baby Playard
BC10062
USER’S MANUAL
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
US:[e-mail]
UK:[e-mail]
AU:[email protected]
US office: Fontana UK office: Ipswich AU office: Truganina

Before You Start
General Warnings:
Danger! Keep all small parts and packaging materials for this product away from
babies and children, otherwise they may pose a choking hazard.
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all Packaging, separate and count all parts and hardware before
installation.
Please ensure that all parts are correctly installed, incorrect installation can lead to
a danger.
We recommend that, where possible, all items are assembled near the area in
which they will be placed in use, to avoid moving the product unnecessarily once
assembled.
Ensure a secure surface during installation, and place the product always on a flat,
steady and stable surface.
Please read all instructions carefully and keep it for future reference.
WARNING!
!
FOR YOUR CHILD'S SAFETY,FOLLOW ALL LABELS ON THIS
PRODUCT AND IN THESE WRITTEN INSTRUCTIONS.DO NOT
USE THIS PLAYPEN IF YOU CAN NOT EXACTLY FOLLOW THE
INSTRUCTIONS THAT COME WITH IT. FAILURE TO FOLLOW
THESE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
! Check this playpen regularly before using it, and DO NOT use it if
any part is loose or missing or if there are any signs of damage. Do
not substitute parts. Contact with us if replacement parts or
additional instructions are needed.
WARNING!
!
FAILURE TO FOLLOW THESE WARNINGS, THE LABELS AND THE
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH.
! The product, including side rails, must be fully erected prior to use.
! Ensure that the sides of this playpen are properly latched or locked
in the appropriate position before placing a child in it.
! DO NOT use this playpen for a child who can climb out of it or who
is taller than 35inch (90cm).
! Children can suffocate on soft bedding. DO NOT place pillows,
comforters or an additional floor pad in this playpen.
! When child is able to pull to standing position, set mattress/ base to
lower adjustment position and remove bumper pads, large toys, and
other objects that could serve as steps from climbing out.
! Use ONLY mattress/ pad provided by manufacturer.
PLAYARD WARNINGS
02 03

WARNING!
!
SUFFOCATION HAZARD-Infants have suffocated:
● In gaps between extra padding and side of the
bassinet/cradle and
● On soft bedding
Use ONLY the pad provided by manufacturer. NEVER add a
pillow, comforter, or another mattress for padding.
To reduce the risk of SIDS, pediatricians recommend healthy infants
be placed on their backs to sleep, unless advised by your physician.
lf a sheet is used with the pad, USE ONLY the one provided by the
bassinet or cradle manufacturer or one specifically designed to fit the
dimensions of the bassinet or cradle mattress.
DO NOT place any cord, strap or similar item in or near this accessory
that could become wrapped around a child's neck.
Check this accessory regularly before using it, and DO NOT use it if
any part is loose or missing of if there are any signs of damage. DO
NOT substitute parts. Contact customer service if replacement parts
or additional instructions are needed.
Children can suffocate on soft bedding. DO NOT place pillows,
comforters or an additional mattress pad in this Accessory.
! DO NOT leave a child unattended in this crib.
! DO NOT use this crib if you can not exactly follow the instructions
that come with it.
! NEVER carry or move the play yard with child in it.
! Always provide the supervision necessary for the continued safety of
your child. When used for playing, NEVER leave child unattended.
Child MUST be under supervision at all times.
! To reduce the risk of SIDS(sudden infant death syndrome),
pediatricians recommend healthy infants be placed on their back
sleep, unless advised by your physician.
! NEVER use a water mattress with this product.
! NEVER refinish this product.
!
WARNING!
FAILURE TO FOLLOW THESE WARNINGS,THE LABELS AND THE
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH.
ENSURE that all bassinet fabric lies FLAT against the playard
frame.
! DO NOT use this accessory if you cannot exactly follow the
instructions that come with it.
! Remove this accessory when a child is in the playpen.
! DO NOT use this accessory for a child who can roll over or who has
reached 22lbs.(10kgs)
! FALL HAZARD-Always check that the bassinet is securely locked on
the frame by pulling upwards.
BASSINET WARNINGS
GENERAL WARNINGS
04 05

! AVOID SERIOUS INJURY by keeping fingers clear of rail joints, top
corners, and from any moving parts when assembling / adjusting the
product to prevent pinching or finger entrapment.
! ENSURE that the play yard is fully erected before each use. Check
that:
● Four(4) top rails are completely LOCKED by pushing down on them;
● The center of the floor is completely PUSHED DOWN;
● The mattress is lying flat and is secured with all four(4)
hook-and-look straps.
! NEVER use the play yard on uneven or unsafe surfaces.
! NEVER use near stoves, heaters or other heat sources.
! ALWAYS keep the play yard away from hazards that may injure your
child.
! DO NOT change, tamper with or modify any part of this product.
! DO NOT use this product if it is damaged in any way or has missing
parts.
! DO NOT allow children to climb into or out of the play yard, or to
hang onto the outside of the play yard to avoid tipping the product.
! NEVER hang anything other than accessories that come with this
product on this play yard as it could cause the product to become
unstable.
! Extended exposure to weather could affect color.
! DO NOT, EXCEPT AS DESCRIBED In THESE INSTRUCTIONS, MODIFY
THIS PRODUCT OR DISASSEMBLE ANY PARTS. This includes adding
any parts or accessories by other manufacturers as non-tested
accessories which can affect the safety of the product.
! This product is NOT intended for commercial use.
! A crib mobile is intended for visual stimulation and is not intended
to be grasped by the child.
! If attached to the crib or playpen, remove when baby begins to
push up on hands and knees. If so designed, mount on wall or ceiling
clearly out of a standing baby's reach.
! Always attach all provided fasteners (strings, straps, clamps, etc.)
tightly to a crib or playpen according to the instructions. Check
frequently.
! Do not add additional strings or straps to attach to a crib or
playpen.
Check the parts list on the back cover to make sure you have
all the parts for this model before assembling the playard.
Storage Bag
Long Curved Bar (2)
Playard
Short Bar with
Connector Knob (2)
Mattress Music Center Parent Organizer
Bassinet with metal
support tubes
Changing Table
Canopy with toys
06 07

TO ASSEMBLE PLAYARD
ATTENTION: Playard must be fully assembled and securely locked
before installing or using other accessories.
1) • Unzip bag and remove Playard
frame (Fig. 1).
Undo the Fasten straps and set the
Mattress aside.
DO NOT push center down yet.
2) • Top rails must be fully erected
before lowering center. Pull up one rail at
a time, hold one hand on each side of the
rail and pull up sharply, do not pull from
the middle where the center latch release
is located, make sure both tubes latch in
place and each rail is rigid (Fig. 2).
IMPORTANT: The center must be raised
while locking the rails. If one rail will lock
but the other side will not then, unlock
the rail by squeezing the release in the
center and try again.
Playard Mattress
Fig. 1
Fig. 2
3) • Once all four (4) top rails are locked in place, push down on the
center handle (Fig. 3a). The center mechanism automatically locks in
place.
IMPORTANT: Test each top rail by pushing down slightly to Confirm
each is rigid and securely in place before use (Fig. 3b).
IMPORTANT: The handle located in the center of the Playard floor
MUST remain raised (Approx. 45.7 cm or 18 inches) while locking the
side rails in place. If the center is not raised the rails will NOT lock.
If you experience difficulty that one side of the rail will lock but the
other side will not, then unlock the rail by squeezing the release in the
center and try again.
4) • Place the Mattress on the floor of the Playard with the padded
side facing up (Fig. 4).
Fig. 3a Fig. 3b
Fig. 4
08 09

To fold PLAYARD
5) • Insert the hook & loop fasteners located on the underside of the
Mattress through the slots in the floor on each end of the Playard
(Fig. 5a). Fasten the hook and loop fasteners to the underside of the
Playard floor to prevent the Mattress from moving (Fig. 5b).
6) • To operate the brakes on the Wheels,
press downward on the brake levers. To
release, lift upward on the lever (Fig. 6).
7) • Release the hook and loop fastener holding the Mattress from
underneath the Playard floor or the Bassinet and set the mattress
aside.
• Do not unlock top rails yet, center of floor must be raised before
unlocking top rails.
• Rotate the center handle counter-clockwise 90 degrees and raise
the center as high as the top rails (Fig. 7). Gather the Legs and
Wheels together towards the center as close as possible so that they
nearly touch.
8) • Locate the rail latch release in the center and bottom side of
each rail. Squeeze the lever with two hands until the rail releases the
two tubes (Fig. 8a), then push down (Fig. 8b).
NOTE: If the top rail(s) do not release completely, DO NOT FORCE!
Lift the center of floor higher. Both tubes must be released for the top
rail to fold.
Fig. 5a Fig. 5b
Fig. 6
Tube
Tube
Latch release
TOP RAIL
Center latch
Rotate before lifting
Fig. 7
Fig. 8a
2
1Push
Raise
Fig. 8b
10 11

11) • Connect opposing Mattress Support Tubes that are attached to
the bottom of the Bassinet (Fig. 11a).
• Before placing the Mattress into the Bassinet, make sure Mattress
Support tubes are connected as seen in Fig. 11b.
12) • Position the Bassinet over and down
into the fully assembled Playard. Secure in
place by pushing down firmly on each
plastic Support clip until all are snapped
into place (Fig. 12).
13) • Place the Mattress into the Bassinet
with the padded side facing upward (Fig.
13).
TO REMOVE THE FULL-SIZE BASSINET
• Remove Mattress from Bassinet. Remove Canopy. Disconnect
opposing Mattress Support Tubes. Unsnap all clips and lift Bassinet.
9) • Gather four (4) corners and center all together
tightly (Fig. 9). Wrap Mattress around Playard frame
with padded side facing inward.
Fig. 9
TO ASSEMBLE THE FULL-SIZE BASSINET
ATTENTION: Playard must be fully assembled and securely locked
before installing or using the Full-size bassinet. (See To Assemble
Playard section). You will need to remove the mattress from the
bottom of the Playard to use inside your Full-size bassinet.
10) • Secure the hooks and loop
fasteners by feeding them through the
loops on the end of the Mattress and
folding them back onto themselves (Fig.
10).
• Place folded Playard into carry bag so
that the handle comes through the opening
between each side of the zipper.
Fig. 10
Full- Size Bassinet with metal support tubes
Fig. 11a Fig. 11b
Fig. 12
Fig. 13
12 13

TO ASSEMBLE CHANGING TABLE
14) • Connect the two (2) Long Curved Bars together (Fig. 14a).
• Insert the assembled curved bars into the Changing Table fabric
(Fig. 14b). Slide the Curved Bars around inside sleeve of the
Changing Table.
• Connect the two (2) Short Bars to each end of the Long Curved Bar
(Fig. 14c). Make sure that the knobs are both facing down and on the
same side (Fig. 14d).
15) • Insert Connector Knob Prongs into holes located on both
corners of the Playard (Fig.15a).
• Turn the Connector Knobs counter clockwise to lock into place (Fig.
15b).
• Flip Changing Table over onto Playard (Fig.15c).
• Snap the two (2) buttons on the flap down onto the Playard (Fig.
15d).
2 Long Curved Bars
2 Short Bars with
Connector Knobs 1 Changing Table
WARNING-FALLING HAZARD: Children may suffer
serious injuries after falling from changing tables.
Falls can happen quickly.
• STAY within arm’s reach.
• ALWAYS secure this product to the support frame
ATTENTION: Playard and Full-size bassinet must be fully assembled
and securely locked before installing or using the
changing table.
Fig. 14a Fig. 14b
Fig. 14dFig. 14c
Fig. 15a
Fig. 15dFig. 15c
Fig. 15b
14 15

TO SECURE THE CHANGING TABLE TO THE PLAYARD TO USE THE CHANGING TABLE RESTRAINT SYSTEM
IMPORTANT! When the changing table is flipped up into the
upper position, the changing table must be secured to the
playard frame using the hook and loop fasteners provided.
16) • Locate the hook and loop
fasteners on the bottom of the changing
table and inside the side rails of the
playard (Fig. 16).
17) • Flip the changing table into its
upper position (Fig. 17).
18) • Secure the changing table to the
playard frame by fastening the hook and
loop fasteners on the underside of the
changing table to the side rails of the
playard frame (Fig. 18).
19) • Place child on the changing table, make sure hands and arms
are clear of the restraint.Bring the restraint around the child’s waist
and clip the male and female ends of the buckle together (Fig. 19a).
• Tighten strap until it fits snug around the child's waist (Fig. 19b).
DO NOT OVER TIGHTEN.
• To remove, unsnap the buckle.
ATTENTION: NEVER use changing table if it is damaged or broken.
TO REMOVE THE CHANGING TABLE
20) • Flip Changing Table to the outside of the Playard. Unsnap
fabric flap of the Changing Table from Playard. Twist Connector Knobs
clockwise to unlock (Fig. 20a).
• Remove Changing Table from the Playard (Fig. 20b) and disconnect
the Short Bars from the Curved Bar by pressing on the snap buttons
and pulling apart.
Remove Curved Bar from the Changing Table sleeve.
Fig. 16
Fig. 17
Fig. 18
Fig. 19a Fig. 19b
16 17

Fig. 20a Fig. 20b
WARNING
ACCESSORIES
Warnings for Toy Accessories including Toybar / Mobile /
Canopy with toys:
PARENT ORGANIZER ASSEMBLY
22) • Parent Organizer: Position each hook So that the hooked end
is facing the rear side of the organizer. Press the hook down firmly
into the slot until it snaps into place (Fig. 22a).
NOTE: The Parent Organizer can only be installed on open sides of
the Playard where the connecting clips can easily be attached without
interfering with other features.
Parent Organizer
Fig. 22a
Deluxe Side Pocket Organizer
21) • The Deluxe Side Pocket
Organizer is conveniently located on the
side of your Playard, it is equipped with
multiple pockets to fit a variety of baby
essentials (Fig. 21).
WARNING: Do not place hot liquids or more than 2 pounds in
the Deluxe Side Pocket Organizer.
Serious burns or unstable conditions could result.
For safety, do not allow children to hang or play with side pockets.
Fig. 21
18 19

23) • CANOPY ASSEMBLY
Insert the both plastic clips of the canopy onto the handrail
WARNING:
• Possible entanglement injury.
• Keep out of baby’s reach.
• Remove Toybar/Mobile/Canopy with toys when baby begins to push
up on hands and knees. Recommended use from birth to 5 months.
• Toys are not intended to be mouthed by the baby and should be
positioned clearly out of reach of the baby's face and mouth.
• ALWAYS attach all provided fasteners (strings, straps, clamps, etc.)
tightly to playard according to these instructions. Check frequently.
• Do not add additional strings or straps to attach to any other crib or
playpen.
• The Toybar/Mobile/Canopy with toys is intended for visual
stimulation and not to be grasped by the child.
OPERATION
24) • The Music Center is designed to
be attached to the playard’s/bassinet’s
long rail (Fig 24).
25) • The Music Center requires 4 AA
batteries (Not Included). Please see
figure 25 for battery installation.
Unscrew the battery door screws and
pull outward on the battery door. Install
batteries as shown. Re-install battery
door and secure with screws.
WARNING: Keep batteries out of children's reach. Old
and new batteries should not be mixed.
Alkaline, standard carbon-zinc, and rechargeable nickelcadium
batteries should not be mixed. Remove batteries before
storing music center for a long period of time.
MUSIC CENTER
Music Operation
*With Vibration
Fig. 24
Fig. 25
20 21

OTHER
WARNING: Changes or modification to this unit not
expressly approved by the party responsible for compliance
are forbidden.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1 this device may not cause harmful interference, and
2 this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult an experienced radio/TV technician for help.
MUSIC NATURE
SOUNDS SLEEP MUSIC
VOLUME
CONTROL VIBRATION NIGHT LIGHT
To listen to MUSIC, press the MUSIC button.
Press the button to change the song.
To listen to NATURE sounds, press the NATURE button.
Press the button to change the sound.
To listen to SLEEP music, press the SLEEP button. Press the
button to change the song.
These 2 buttons control the unit’s volume.
NIGHT LIGHT: To use the night light, press the NIGHT
LIGHT button.
VIBRATION: To use the VIBRATION, press down VIBRATION
button once to activate the speed, press again for faster
speed. Press it again to reduce the speed.
22 23