Cotell CT602A(1S) User manual

C
T602A(1S)
User Manual
1

C
T602A(1S)
User Manual
2
CONNECTING C
T602
A(
1
S
)
Bathroom Telephone
Included with the C
T602A
(
1S
)
phone are (one each):

Base uni
t

Coiled handset cord

User guide

Handset

Line cord
INSTALLATION
The phone can be used on desktop and wall mount.
1.
Place bracket under base unit; connec
t one end
coiled handset
cord to outer RJ11 line
interface on base unit and another end to
the handset RJ11 Socket
.
2.
Connec
t one end of the RJ11
tele
phone
connector
to
the
junction box and another end
to the telephone
RJ11 socket
located at the back of the
telephone.
3.
For Wall
-
mount configuration, remove the bracket under the base unit;
align the slot at
the base of the telephone to the screw on the wall.
C
T602
A(
1S
)
FEATURE
S

1
-
Line

Analog

Surf
ace
M
ount
T
echnology with CPU control

High
immunity to electro
-
mag
netic radiation

Ringer volume control
（
HI
-
LO
）
slide switch

Hold,
flash
and redial

Auto disconnect on busy tone detection

Adjustable flash
-
hook timer

C
T602A(1S)
User Manual
3
C
T602
A(1
S
)
DIAGRAM
C
T602
A(1
S
)
BUTTON ASSIGNMENT
FUNCTION
KEY
FEATURE
DESCRIPTION
1
HANDSET
F
or answering the call
.
2
DIAL
PAD
Keypad for dialing
.
3
FLASH
Act as
an electronic hook
-
switch
to
activate call transfer
.
4
REDIAL
REDIAL last number dialed
.
5
MUTE
P
ress key
activate or
deactivates
MUTE
function.
6
HANDSET JACK
M
odular jack for handset
.
7
HANDSET
CORD
Co
nnecting the handset jack to
the base unit
.
8
RINGER(
HI
-
LO
)
A
djust the ringer volume to
high or
low.
9
SCREW SLOT
Wall mount slot.
10
TEL JACK
Telephone line jack
.
11
MSG
Light up as message or
incoming
call indicator
.

C
T602A(1S)
User Manual
4
PLACING A CALL
1.
Lift up the ha
ndset
.
2.
Listen for dial tone
, d
ial the desired
telephone
number
or press a
memory key to
automatically dial a number
.
3.
To end the call, hang up by placing the handset back
on
the cradle.
RECEIVING A CALL
An audible ring
ing
and flickering red
message
waiting
light will indicate an incoming call
.
1.
Lift
up
the handset
.
2.
To end the call, hang up by placing the handset back
on
the cradle
.
ADJUSTING THE RING VOLUME
1.
Locate the
volume
control
at
th
e back of the telephone labeled
RINGER
HI
-
LOW slide
switch.
2.
Slide the
switch to the desired
HI
-
LOW
ring volume.
REDIAL
To REDIAL the last telephone number dialed
,
1.
Lift up the handset
or press the SPEAKER.
2.
Press the REDIAL key
to activate the last number dialed.
MUTE
T
o place calls on mute
mode
during
conversation.
1.
Press M
UTE
key
,
place the handset back on the cradle
,
the
caller
will hear background
music.
2.
L
ift up the handset
,
press MUTE
key again will
return
to
the original
conversation
.
AUTO DISCONNECT
The telephone will auto disconnect the line after detecting 8x busy t
one upon calling party
on
-
hook
.

C
T602A(1S)
User Manual
5
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS.
INCLUDING THE FO
LLOWING:
1.
READ
AND UNDERSTAND ALL INSTRUCTIONS
IN THIS MANUAL.
2.
FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT.
3.
UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING. DO NOT USE LIQUID
CLEANER OR AEROSOL CLEANERS. USE ADAMP CLOTH FOR CLEANING.
4.
DO NOT USE THIS PRODUCT NEAR WATER FOR EXAMPLE NEAR A BATHTUB, WASH BOWL,
KITCHEN SINK OR LAUNDRY TUB, IN AWET BASEMENT, OR NEAR A SWIMMING POOL.
5.
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE
CART, STAND OR TABLE. THE PROD
UCT
MAY FALL, CAUSING SERIOUS DAMAGE
TO THE PRODUCT.
6.
SLOTS AND OPENINGS IN THE CABINETAND THE BACK OF BOTTOMARE PROVIDED FOR
VENTILATION, TO PROTECT IT FROM OVERHEATING, THESE OPENINGS MUST NOT BE
BLOCKED OR COVERED. THE OPENINGS SHOULD NEVER BE BLOCKED BY PLACING THE
PRODUCT ON THE BED, SO
FA, RUG ORANY OTHER SIMILAR SURFACE. THIS PRODUCT
SHOULD NEVER BE PLACED NEAR OR OVER A RADIATOR OR HEAT REGISTER. THIS
PRODUCT SHOULD NOT
BE PLACED IN A BUILT
-
IN INSTALLATION UNLESS PROPER
VENTILATION IS PROVIDED.
7.
NEVER PUSH OBJECTS OF ANY KIND INTO THIS
PRODUCT THROUGH CABINET SLOTS
AS
THEY MAY TOUCH DANGEROUS VOLTAGE POINTS OR SHORT OUT PARTS THAT
COULD
RESULT IN A RISK OF FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY
KIND ON
THE PRODUCT.
8.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE THIS
PRODUC
T,
BUT
TAKE IT TOA QUALIFIED SERVICEMEN WHEN SOME SERVICE OR REPAIR WOR
K
IS
REQUIRED. OPENING OR REMOVING COVERS MAY EXPOSE YOU TO DANGEROUS
VOLTAGES OR OTHER RISKS. INCORRECT REASSEMBLE CAN CAUSE ELECTRIC
SHOCK
WHEN THE APPLIANCE IS SUBSEQUENTLY US
ED.
9.
UNPLUG THIS PRODUCT
FROM THE WALL OUTLETAND REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL
UNDER THE FOLLOWINGCONDITIONS
:
-
WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR
FRAYED
-
LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
-
IF THE PRODUCT HAS BEEN EXPOSED
TO RAIN OR WATER.
10.
IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING THE OPERATING
INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT ARE COVERED BY THE
OPERATING INSTRUCTIONS BECAUSE IMPROPER ADJUSTMENT OF OTHER CONTROLS
MAY RESULT IN DAMAGE AND WILL
OFTEN
REQUIRE EXTENSIVE WORK BY A
QUALIFIED
TECHNICIAN TO RESTORE THE PRODUCT TO NORMAL OPERATION.
-
IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN DAMAGED.
-
THE PRODUCT EXHIBIT ADISTINCT CHANGE IN PERFORMANCE.
11.
AVOID USING A TELEPHONE (OTHER THAN A CORDL
ESS TYPE) DURING AN
ELECTRICAL
STORM. THERE MAY BE A REMOTE RISK OF ELECTRIC SHOCK FROM LIGHTING.
12.
DO NOT USE THE TELEPHONE TO REPORTA GAS LEAK IN THE VICINITY OF THE LEAK.SAVE
THESE INSTRUCTIONS