Craftex CX series User manual

CX108N
18” WOOD BAND SAW
User Manual
Version 1.0

2
TABLE OF CONTENTS
General Safety Instructions .................................................................................... 3
Specic Safety Instructions ..................................................................................... 4
Features .................................................................................................................. 5
Physical Features .................................................................................................... 6
Setup ............................................................................................................... 7
Un-packing .............................................................................................................. 7
Proper Grounding .................................................................................................. 8
Assembly and Adjustments ............................................................................ 9
Blade Tracking ........................................................................................................ 12
Basic Controls ........................................................................................................ 13
Test Run .................................................................................................................. 13
Blade Tension . ........................................................................................................ 14
Adjusting the Blade Tension ................................................................................... 14
Guide Bearings Adjustments ................................................................................. 14
Table Stop Adjustment .......................................................................................... 15
Table Tilt Scale Calibration ..................................................................................... 16
Table Alignment ..................................................................................................... 16
Guide Post .............................................................................................................. 17
Work-Piece Inspection ........................................................................................... 17
Cast Iron Wheels ..................................................................................................... 18
Coplanar Adjustment .............................................................................................. 18
Operations ..................................................................................................... 19
Ripping .................................................................................................................. 19
Cross Cutting ......................................................................................................... 19
Re-Sawing ............................................................................................................... 20
Cutting Curves ....................................................................................................... 20
Connecting to a Dust Collector ............................................................................. 20
Maintenance ................................................................................................... 21
Removing/Installing Blade ...................................................................................... 21
Blade and Table Alignments ................................................................................. 21
Tilting the Table Backward .................................................................................... 22
Table and Base ...................................................................................................... 22
V-Belts .................................................................................................................... 22
Removing/Replacing the V-Belts .......................................................................... 23
Parts Breakdown and List ............................................................................ 24-30
Warranty ............................................................................................................... 31

GENERAL SAFETY INSTRUCTIONS
Extreme caution should be used when operating all machinery. Know your machine, be
familiar with its operation, read through the owner’s manual and practice safe usage
procedures at all times.
ALWAYS read and understand the user
manual before operating the machine.
CONNECT your machine ONLY to the
matched and specic power source.
ALWAYS wear safety glasses respirators,
hearing protection and safety shoes, when
operating your machine.
DO NOT wear loose clothing or jewelry and
secure long hair in a net or tied back when
operating your machine.
A SAFE ENVIRONMENT is important.
Keep the area free of dust, dirt and other
debris in the immediate vicinity of your ma-
chine.
BE ALERT! DO NOT use prescription or
other drugs that may affect your ability or
judgment to safely use your machine.
DISCONNECT the power source when
changing blade and / or making
adjustments.
NEVER leave a tool unattended while it is in
operation.
NEVER reach over the table when the tool is
in operation.
ALWAYS keep blades, knives and bits sharp-
ened and properly aligned.
ALL OPERATIONS MUST BE performed
with the guards in place to ensure safety.
ALWAYS use push sticks to safely feed your
work through the machine.
ALWAYS make sure that any tools used for
adjustments are removed before operating
the machine.

4
CX108N - 18” Wood Bandsaw
SPECIFIC SAFETY INSTRUCTIONS
WARNING
The safety instructions given above can not be complete because the environment in every shop is
different. Always consider safety rst as it applies to your individual working conditions.
CX108N is perfect for cutting various types
of wood.
ALWAYS INSPECT the blade for any cracked
or missing teeth before operating the band
saw.
ALWAYS ENSURE that the blade tension is
properly set for the type and width of blade
installed.
NEVER place your ngers or hands in the
line of cut. If you slip, your hands or ngers
may come into contact with the blade. Al-
ways use a push stick when ripping narrow
pieces.
DO NOT back the work-piece away from the
blade while cutting. Always turn off the ma-
chine if you are backing out a cut.
ALL GUARDS must be in place while operat-
ing the band saw to ensure safety.
ALWAYS FEED the stock smoothly. Do not
force or twist the work-piece while cutting.
ALWAYS ENSURE that the band saw blade
guard is no more than 1/2” above the stock.
MAKE SURE before making any adjust-
ments, the switch is in the “OFF” position
and the cord is un-plugged from the power
source.
NEVER LEAVE the band saw unattended
while it is running.
DO NOT attempt to remove jammed pieces
unless the band saw has come to a complete
stop and the power switch has been turned
to the OFF position.
NEVER TURN ON the band saw if the blade
is in contact with your workpiece.
ALWAYS ENSURE that the guide bearings
are properly set to prevent blade wander.
ALWAYS MAKE CERTAIN that the guide
bearings are properly adjusted to guide the
blade properly.
MAINTAIN AND SERVICE your band saw
regularly as instructed in the user manual.
MAKE SURE you have read and understood
all the safety instructions in the manual and
you are familiar with your band saw, before
operating the CX108N. If you fail to do so,
serious injury could occur.

CX108N - 18” Wood Bandsaw
FEATURES
As part of the growing line of Craftex woodworking & metalworking equipment, we are
proud to offer the CX108N - 18” Variable Speed Band Saw. The Craftex name guarantees
Craft Excellence. By following the instructions and procedures laid out in this user manual,
you will receive years of excellent service and satisfaction. The CX108N is a professional tool
and like all power tools, proper care and safety procedures should be adhered to.
Motor ................................................... 2HP, 220V Single Phase, 3450 RPM
Switch ................................................. Magnetic Switch
3 Speed ................................... 1480, 2300 & 3260 FPM
Cast Iron Table Size ............................ 20” x 24
Table Tilt ............................................. 0° to 10° Left and 0° to 45° Right
Wheel .................................................. 18”
Max Blade Width ................................. 1”
Min Blade Width .................................. 1/8”
Maximum Cutting Height ..................... 12”
Floor to Table Height.. ......................... 38-1/2”
Cutting Capacity/Throat.. ..................... 17-5/8”
Dust Collection Ports ........................... 2 Ports@ 4”
Blade Length ...................................... 133”
Bearings .............................................. Sealed and Permanently Lubricated
Computer Balanced Cast Iron Wheels ...... .Yes
Co-Planer Adjustment ......................... Yes
Powder Coated Paint .......................... Yes
Precision Ripping Fence ..................... Yes
Quick Release Tension Adjustment .... Yes
Overall size ......................................... 30” x 41” x 74”
Carton Size ............................. 32” x 76” x 19”
Weight.. .......................... 173 GW
Warranty ............................................. 3 Years

6
CX108N - 18” Wood Bandsaw
PHYSICAL FEATURES
Quick Release Blade
Tension Handle
One Piece
Construction
On/Off
Switch
Fence
Powder Coated
Paint
Base
Lower Cabinet
Lock Knob
Table
Rear
Fence Rail
Guide Post
Guide Post
Lock Knob
Blade Guide
Adjustment
Hand Wheel
Upper Cabinet
Lock Knob
Fence Cam
Lock Handle
Front
Fence Rail
Guide Bearings
Upper

Figure-1 Inventory
List of Contents
O. Flat Washer 1/4”-16 1.2mm ......................... 4
P. Hex Bolt 1/4”*5/8” .................................... 4
Q. Miter Gauge Holder ..................................... 1
R. Fence Holder ................................................ 1
S. Miter Gauge .................................................. 1
T. Scale (for the front rail) .................................. 1
U. Fence Assembly ............................................ 1
V. Front Rail ....................................................... 1
W. Rear Rail ....................................................... 1
X. Front Rail Brackets ....................................... 2
Y. Rear Rail Brackets ......................................... 2
Z. Front Rail Knobs ............................................ 2
AA. Rear Rail Knobs ......................................... 2
BB. Flat Washers 3/8” ....................................... 2
CC. Knobs 3/8”-16 ............................................ 2
DD. Hex Bolts 1/4”-20x1/2” ........................................ 2
EE. Lock Washer 1/4” ...................................... 2
F F. Flat Washers 1/4” ........................... ........... 2
GG. Table Insert................................................. 1
Figure-2 Inventory
Setup
Before setting up your machine you need to
read and understand this user manual
completely.
The unpainted surfaces of this band saw are
coated with a rust preventive waxy oil and you
will want to remove this
before you begin assembly. Use a
solvent cleaner that will not damage painted
surfaces. amount of cleaner/degreaser, then let it
soak for 5-10 minutes.
WARNING
CX108N is a heavy machine. Do not
over-exert yourself. Use a fork truck or
get the help of an assistant or a friend.
Unpacking
The machine is properly packaged in a carton
for safe transportation. When unpacking,
carefully inspect the crate and ensure that noth-
ing has been damaged during transit. Open the
crate and check that the machine is in good
condition.
The hardware (screws, washers etc) might be
shipped in a plastic bag.
After the machine has been un-packed, check
that all loose parts and
hardware are present.
List of Contents
A. Allen Keys 2, 3mm ................................... 2
B. Wrench ..................................................... 1
C. 1/4” Lock Washer .................................... 2
D. Flat Washer 5/16” .................................... 1
E. 1/4” Lock Washer .................................... 2
F. Flat Washer ............................................. 1
G. Knob Bolt 3/8-16 x 1 1/4 ........................ 1
H. Hex Bolt 5/16-18x1 .................................. 1
I. Angle Adjustment Plane ............................ 1
J. Hex Bolt 1/4-20x1/2 ................................. 2
K. Bushing .................................................... 1
L. Nylon Nut 5/16-18 ................................... 1
M. Adjustment Bar Bracket ......................... 1
N. Square Nut 5/16 ...................................... 4
HG
A
B
GG
E
K
J
C
L
MD
I
DD
CC
EE
BB
FF
F
O
P
N

8
Proper Grounding
Grounding provides a path of least
resistance for electric current to reduce the
risk of electric shock.
CX108N is equipped with a 220 single
phase motor which features a 3-conductor
cord and a 3-prong grounded plug to t a
grounded type receptacle. Make sure the
cord is plugged into a properly installed and
grounded power outlet.
To prevent electrical hazards, have a
qualied electrician ensure that the line is
properly wired.
This machine is for use on a normal 220-volt
circuit and is factory-equipped with a
specic electric cord and plug to permit
connection to a proper electric circuit. Make
sure that the machine is connected to an
outlet having the same conguration as the
plug. If an adapter plug is used, it must be
attached to the metal screw of the
receptacle.
Figure-3 220-Volts Outlet for CX108N
WARNING
Improper connection of the
equipment-grounding conductor can
result in a risk of electric shock. Check with
a qualied electrician if you are in doubt
as to whether the outlet is properly
grounded.
It is strongly recommended not to use
extension cords with your CX108N. Always
try to position your machine close to the
power source so that you do not need to use
extension cords.
In case if you really nd it necessary to use
an extension cord, make sure the extension
cord does not exceed 50-feet in length and
the cord is 12-gauge to prevent motor
damage.
Your CX108N is equipped with a cord having
3-prongs which ts a 3 prong grounded
receptacle as shown in gure-3. Do not
remove the grounding prong to t it into a
2-pronged outlet. Always check with a
qualied electrician if you are in doubt.

Assembly
Follow the steps below to assemble your
band saw:
Take the band saw table and put it upside
down on oor and make sure that all the
table bolts shown in the gure are tight. See
gure-4
Figure-4 Table Turnion bolts
Figure-5 Installing the angle adjustment
brackets
Attach the Adjustment bar bracket #176 to
the underside of the table using the 2 screws
#173 and the washers, #17, and #103. Secure
the Angle adjustment plane #172 to the
adjustment bar bracket #176 with the hex
bolt #171, washer #122 and the locking nut
#175.
Now turn the table up right, and remove the
table pin from the table slot and the table
insert (if already installed) and move the table
in position around the blade, guiding through
the table slot. See gure-6
Figure-6 Installing the table
Position the table on the base in such a way
that the bolts under the table extend through
the holes on the base. Thread the two knobs
on the bolts ( do not tighten). See gure-7
Figure-7 Knobs threaded on the bolts
Position the table on the table stop and the
base so that the table is perpendicular to the
blade. See page 15 for details.

10
Place the washer #60 on the knob #170.
Pass the threaded stud of the knob through
the slot in the angle adjustment plane. Then
install the spacer on the threaded stud of
the knob and then thread the knob into the
body of the band saw.
Tighten the knob to secure the table at the
desired angle required for your cutting
operation.
Install the table insert at the center of the
table and the table pin into the table slot as
shown in gure-8.
Figure-8 Installing table insert and
table pin
Figure-9 Rear rail brackets attached
Now, attach the rear rail to the brackets
using the knobs provided. See gure-11.
Figure-10 Installing the rear fence rail
Take the rail bracket (smaller) and attach it
to the table using cap screws provided. See
gure-9 .
Take the rail brackets (larger) for the front
fence rail and attach it to the table using the
cap screws provided.
Place the front fence rail on the brackets and
insert the knobs through the hole on each
bracket and thread the square nuts onto the
ends of the knobs a couple of turns to
tighten the fence rail in place. See gure-11.

Figure-11 Front fence rail installed
Now take the fence and lift up the handle.
Place the fence on the front fence rail until it
touches against the blade.
Use a pencil to mark the fence rail where the
fence scale indicator on the right hand side is
pointing (there is a gap just behind the
indicator plate where you can mark the rail).
This mark will indicate where to align the O”
mark when install the scale.
Now, remove the fence from the rail and
install the adhesive backed scale on the front
fence rail.
Figure-12 Adhesive backed scale attached
to the front rail
Once you have attached the adhesive backed
scale to the rail, place the fence on the rail
and tighten it in place by pushing down the
handle. See gure-14
Figure-13 Fence installed on the rails
Attach the miter gauge holder and the
fence holder to the back of the saw using
screws and washers provided see gure-14
Figure-14 Miter gauge holder and fence
holder installed
Fence Holder
Miter Gauge
Holder

12
Blade Tracking
Blade tracking refers to the blade
remaining in the same position on the
upper and lower wheels. When rotating
the wheel by hand, if it moves forward
or backward on the wheel then tracking
needs to be adjusted.
Although the blade tracking of this band
saw is factory set, you should check it
again to make sure that the blade is
centered on the wheels. The misalignment
of the blade can be controlled by adjusting
the upper wheel tilt lock nuts.
Disconnect the machine from power and
open the upper wheel cover. Rotate the
upper wheel by hand slowly and see how
the blade rides on the wheel.
If the blade is not properly aligned and
needs to be adjusted, loosen the lock nuts
shown in gure-15 and turn the knobs.
Figure-15 Knobs and Locks Nuts
Turn the knobs clockwise:
If the blade moves towards the front edge
of the wheel. It makes the top of the wheel
to tilt back and moves the blade towards
the center.
Turn the knobs counter-clockwise:
If the blade moves towards the back edge
of the wheel. It makes the top of the wheel
to tilt to the front and moves the blade to-
wards the center.
Figure-16 Blade centered on the wheel
When you have adjusted the blade tracking,
re-tighten the lock nuts.
IMPORTANT
In very rare cases if the blade tracking is
not adjusted by tilting the upper wheel,
then you will have to make minor
adjustments to the angle of tilt of the
lower wheel. Loosen the four hex bolts
and rotate the sleeves to tilt the lower
wheel to get the proper angle of tilt and
tighten the bolts back. Remember, this
adjustment is done only if the blade
tracking is not adjusted by tilting the
upper wheel.
Figure-17 Lower wheel adjustment sleeves

Basic Controls
The basic controls of this machine are shown
in the gure below. Use the gure and read
the text to understand what the basic
controls of this band saw are.
Figure-18 Basic controls of CX108N
A. The power switch turns the power on/
off to the motor switch.
B. The motor switch start and stops the
motor and only works after the power switch
has been turned on.
C. The guide post hand wheel raises or
lowers the post guide post.
D. The blade tension/ quick release lever
increase or decreases blade tension when
rotated. Lifting the handle activates the
quick release.
IMPORTANT
Make sure you have done the tracking
adjustment and the blade is centered on
the wheels before you start the band saw
for a test run. See page-12 for details on
blade tracking.
WARNING
This machine can perform many types of
operations which are beyond the scope of
this manual and are very dangerous if
performed incorrectly. The safety
instructions given in this manual can not
be complete because the environment in
every shop is different. Always consider
safety rst as it applies to your individual
working conditions.
TEST RUN
Once you have assembled your machine
completely, it is then time for a test run to
make sure that the machine works properly
and is ready for operation.
During the test run if there is any unusual
noise coming from the machine or the
machine vibrates strangely, stop the
machine immediately and disconnect
from the power source and investigate the
source of the problem with your machine
refer to the trouble shooting.
READ THE MANUAL
Before starting the band saw, make sure
that you have read and understood the
manual and you are familiar with the
functions and safety features on this
machine. Failure to do so may cause
serious personal injury.

14
Blade Tension
A properly tensioned blade is very important
to get the best performance from any band
saw. If the blade is too loose there is a
possibility that the blade will slip or drift off
the line while in operation and it will be hard
to have accuracy in the line of cut. If the
blade is tensioned too tightly, it will be very
difcult to make tighter radius cuts and there
will be a greater possibility of blade
breakage.
When using a wider blade for making
straight cuts, for re-sawing or making wide
radius cuts, tighter blade tension is
recommended; while using narrower blades
for cutting shorter stock or making tighter
radius cuts, less blade tension is
recommended.
The information above is just a guideline for
you to understand to set the blade tension
according to the cut. However, understand-
ing the blade tension adjustment comes with
practice with the machine.
Look at the blade tension scale located at
the back of your band saw. The scale shows
the ideal blade tension adjustment according
to the width of the blade.
Figure-19 Quick release blade tension handle
and scale
Adjusting the Blade Tension
To adjust the blade tension, lift the blade
tension handle shown in gure-19 and turn
it. Turning the handle clockwise will increase
the tension on the blade while turning the
handle counter-clockwise will decrease the
blade tension.
IMPORTANT
All blades stretch with use, and the scale
at the back of your band saw (shown in
gure-19) is just an approximation. So, do
not rely on any adjusted measurement for
a long period of time as the blades stretch
and the tension on the blade changes.
IMPORTANT
To prolong the life of the blade and reduce
blade stretching, when the machine is not
in use for period of 24 hours or more
release the tension on the blade.
Guide Bearings Adjustment
The guide bearings (beside) and thrust
bearing (behind) the blade, support the
blade during cutting operations. Properly
adjusted support bearings play, an
important role in getting accurate cuts.
To adjust the guide bearings, turn the
machine off and disconnect the cord from
the power source and prevents the blade
from wondering, therefore producing
straight cuts.
Remove the blade guard and use a screw
driver to loosen the screws located on each
of the two guide bearings as shown in
gure-20.

Figure-20 Set Screws
Adjust the bearings so that the space
between the guide bearing and the blade
should be 0.02” which is thickness of a sheet
of paper. See gure-22
Now, retighten the set screws to lock the
guide bearings in place.
Loosen the lock levers shown in gure-23
and move the guide shafts in or out so that
the guide bearings are 1/32” behind the
blade gullet teeth and the thrust bearing,
is 1/64” behind the back edge of the blade.
Once the bearings are at the correct
position behind the blade, tighten the lock
lever to lock the bearings in place.
See gure-23.
Figure-21 Table sitting on the table stop
Figure-22 Distance of the bearings behind
the blade.
Adjust the lower bearings in the same
manner.
Table Stop Adjustment
See gure-21 for reference.
CX108N features a table stop which allows
the table to easily come to a 90° if the table
is tilted.
To adjust the table stop so that the table sits
at 90°, you should rst make sure the switch
is in “OFF” position and the power cord is
unplugged. Loosen the two lock knobs
under the table and loosen the hex nut
which locks the table stop bolt.
Now, place a square on the table as shown
in gure-23 and adjust the table stop so that
the table is at a 90° with the blade.

16
Figure-23 Adjusting the table at 90oto
the table using square
Once the table is at 90owith the blade,
tighten the hex nut and the knobs.
Table Tilt Scale Calibration
To calibrate the table tilt scale:
Make sure the table is at 900to the blade
and the blade tensioning and tracking is
properly set. (See Page 12 & page 14 for
details)
Disconnect the machine from the power
source and loosen the pointer screw shown
in gure-24. Align the tip of the pointer
with the O” mark on the tilt scale and
tighten the pointer screw.
Figure-24 Table tilt scale
Table Alignment
To make accurate cuts with your band saw,
the table should be aligned properly with
the blade.
To align the table:
Make sure the blade tension and tracking
is done correctly. Disconnect the machine
from the power source and loosen the
table trunnion bolts under the table shown
in gure-25.
Figure-25 Table trunnion bolts
Place a straightedge on the table so that the
straightedge touches the blade and is
parallel to it as shown in gure-25. Make
sure the straight-edge touches only the at
part of the blade, not the teeth.
Now, use a ruler to measure the distance
between the miter slot and the straight
edge on both sides on the table R & L. See
gure-26
Figure-26 Aligning the table with the blade
using a straight-edge

Adjust the table until the distance on both
sides of the table is equal and tighten the
table trunnion bolts.
Guide Post
The guide post assembly can be moved up
or down above the work-piece. The
movement of the guide post is controlled
with the hand wheel shown in gure-27.
Figure-27 Guide post
To make accurate cuts and to reduce the
blade slipping out of position, it is
recommended to keep the guide post no
more than 1” above the work-piece while
cutting operation.
To Adjust the Guide Post Assembly:
Make sure the switch is turned off and the
cord is disconnected from the power source.
Loosen the guide post lock knob on your
band saw shown in gure-27 and rotate the
hand-wheel to move the guide post assem-
bly up or down.
When the guide post assembly is about 1”
above the work-piece, lock the guide post in
place using the lock knob.
Work-piece Inspection (Wood)
Before cutting any wood, make sure to
inspect the work-piece for nails, staples,
small pieces of stone or metal and any other
object which might come in contact with the
blade.
If the wood contains any of these objects
and it comes in contact with the blade, the
object might y and hit the operator or
seriously damage the blade. For a safe
cutting method always inspect your
workpiece carefully before cut and wear eye
protection.
Some woods with excessive twisting or
wrapping are un-stable while cutting and are
dangerous to cut because during
operation the work-piece can move
unexpectedly which either damage the
blade or hurt the operator.
If the wood is slightly cupped, make sure the
cupped face of the wood is held against the
fence. If the bowed side of the workpiece
is held against the fence, the workpiece will
move while cutting.
WARNING
The information above is just a guideline
for you to understand how to cut a
workpiece with slight cupping. If you are
not sure and do not have any experience in
cutting cupped stock, do not cut it.
Failure to follow these instructions might
bring personal injuries to the operator or
serious damage to the blade.
Some stock with large knots can damage
the blade and wet stock will give a poor
result.

18
Cast Iron Wheels
The CX108N comes with heavy duty cast
iron wheels for added stability and overall
performance.
A coplanar shim adjustment also added for
better alignment of the wheels that allow
the blade to run as straight as possible
ensuring straight and accurate cuts.
This feature will help improve the band saw
performance with the wheels working
together instead of against each other.
The end result will give you less vibration,
more power, accuracy and less wandering.
This will be noticed most when it comes
to resawing and making straight cuts with
blades larger than 1 /4”.
Coplanar Adjustment
To move the wheel out remove the nut and
then remove the wheel.
Figure 28. Washer
Now you can add shims to the back of the
wheels as required. Replace the wheel and
any remaining shims and the nut and
tighten. To move the wheel in, remove the
cast iron wheel as mentioned above and
remove the shims from behind the wheel.
Replace the wheel, shims and nut and
retighten.
Figure-28 Washer
Figure-29 Top wheel back shims

Operations
Before operating the band saw make sure
you have performed the following adjust-
ments:
Blade tension adjustment
Blade tracking adjustment
Guide bearings adjustment
Make sure all the guards are in place
WARNING
CX108N produces ne dust particles
during cutting operation which is very
dangerous for health. Always connect
your band saw to a dust collector.
Ripping
Cutting solid wood with the grain cutting
down the length of the work-piece is called
ripping.
Adjust the fence on the rails, according to
the width of the cut on the work-piece and
turn the hand-wheel to set the guide post
assembly 1” above the work-piece.
Now, turn the band saw ON and use a push
stick to push the workpiece against the
blade. See gure-30.
WARNING
Do not use your ngers to feed narrow
work-pieces into the blade. If you slip,
your ngers might come close the blade.
Always use a push stick.
Figure-30 Ripping on CX108N
Crosscutting
Cutting solid wood across the grain and
in plywood cutting across the width of the
work-piece is called crosscutting.
Mark the work-piece where you want to
start the cut from and make sure the miter
gauge is at 90° position on the miter slot.
Place the work-piece on the table so that
the marked point is aligned with the blade
and hold the work-piece against the miter
gauge.
Turn the band saw ON and feed the
work piece against the blade. See gure-31.
Figure-31 Crosscutting on CX108N

20
Resawing
Cutting a work-piece into two or more
thinner pieces is called resawing. Wider
blades give better result, when resawing.
To resaw a work-piece make sure that the
table is at a 90° with the blade and use a
wider blade for better results.
Adjust the fence according to the width of
the cut you want, and lock it in position.
Turn the band saw ON and feed the
workpiece into the blade using feed paddles
until the blade is completely through the
workpiece.
Figure-32 Resawing on CX108N
Cutting Curves
For cutting curves always try to use narrower
blades. When cutting curves feed the stock
into the blade and turn it very carefully so
that the blade follows the line of cut and
make sure the blade does not twist.
Make relief cuts through the waste part of
the work-piece which makes the job easier
and prevents the blade from twisting.
Connecting to a Dust Collector
CX108N features two 4” diameter dust
ports to connect to a dust collector.
When connecting to a dust collector, use
a proper sized hose and make sure all the
connections are sealed tightly.
You should use a dust collector with at least
a 500 CFM rating.
Figure-33 CX108N connected to dust collector
WARNING
The saw dust produced by the band saw can
go into your lungs and cause serious health
problems. Make sure the band saw is
connected to a dust collection system while
operating it.