Craftsman 706.146440 User manual

OPERATOR,s MANUAL
Please indicate the following information from the service Part drawing provided.
Model Number:
Model Description:
*Product You Purchased may vary from Picture shown.
Caution: Read and follow all
Use of this Product _p=;. .. Safety Rul,=- _....
_,,,entforfUtu%_ie_/n_truct_Onsbeforef_rst
Distributed by Sears Brands Management _n ....... _r_nc_.

SAFETY WARNINGS AND CAUTIONS:
•Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product
damage.
• Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product
damage.
•DO NOT stand on this product. You may fall which may cause personal injury.
•DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
• Appropriately secure this product before moving it with a forklift.
•DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. This
may cause product damage or personal injury.
• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface,
which may cause personal injury or product damage.
•DO NOT step in the drawers. You may fall which may cause personal injury.
• Maximum combined weight limit not to exceed 500 pounds. If the limit is exceeded, the product could collapse and cause
personal injury or product damage.
Tools Required:
Socket wrench
1/2" Socket
1/2" Wrench
Crosstip Screwdriver
Square
Tape measure
Hardware Included B(2)\
(2o)
BB (18)
CC (4)
........E .........C ........F
fCall 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
to
Refer Service Parts Drawing for full listing of Service Parts.
2

STEP (1):
BB(6)
• While unpacking unit, if you wish, you can leave the
workbench top inside the original packaging to prevent the top
from being scratched, and complete the assembly steps.
• Determine the front and back of the top before starting.The
back of the top (A) has the 6 holes closest to the edge.
• Assemble (1) leg section (D or E) in each side of the top (A)
using (3) screws (BB) in each. The back side of the legs have
holes in them, the fronts do not have any holes.
/
STEP (2):
AA (8) BB(12)
• Attach the front and back rails (B) to the legs using (8) bolts
(AA).
• Finger tighten.
• Attach to the workbench top using (12) screws (BB).
\
STEP (3):
AA(12)
• Attach a angle brace (G) to each side of the legs using (3)
bolts (AA)on each.
• Finger tighten.
AA
STEP (4): AA(4)
• Attach the last rail to the back of the legs using (4) bolts (AA).
• Finger tighten.
• Square the unit and wrench tighten all fasteners.

fSTEP (5): _'
CC (4)
•Assemble (2)(CC)in each of the leg assemblies (D & E).
Some adjustment may be necessary after workbench is in
desired location.
• Finger tighten.
?
?
J
STEP (6):
• Place the workbench in its upright position.
• Measure from the right leg 5".
• Attach the CRAFTSMAN nameplate (F) on the front rail in this
location. Centering the nameplate horizontally on the rail.
/
/
desired position with 1/2
open end wrench as shown. ,,"
desired position. The weight
of the unit will keep it in .....
place. "_
\\
\\\\
f• Periodically the surfaces should be cleaned with a mild
detergent and water.
• Periodically check the fasteners to be sure they have not
loosened. If they have, re-tighten.
• Grease and oil can be removed with most standard cleaning
fluids. For safety, use a nonflammable cleaning fluid.
• Auto wax will preserve the unit's luster finish. Apply the wax as
to a car. The wax will also help protect the unit against
scratches.