Craftsman 559.741710 User manual

OWNER’S
MANUAL
MODEL NO.
559.741710
Caution:
Read and Follow
all Safety Rules
and Instructions
Before Operating
This Equipment
Save These
Instructions !
SEARS, ROEBUCK and Co., Hoffman Estates, IL 60179 U.S.A.
2 HP, 13 AMP, 120 V, AC, ELECTRIC
HIGH PRESSURE WASHER
lAssembly
lOperation
lCustomer Responsibilities
lService and Adjustment
lRepair Parts
1250

2
IMPORTANT SAFETY RULES
WARNING - Risk of Injection or Injury -
•Do Not Direct Discharge Stream At Persons.
•Read this operator’s manual carefully, become
familiar with the controls and know how to operate
your sprayer.
•Do not allow children to use your High Pressure
Washer. Never allow adults to use the High Pres-
sure Washer without proper instructions.
•Keep the area of operation clear of all persons,
especially small children and pets.
•Use the High Pressure Washer only as the ma-
nufacturer intended and as described in this ma-
nual.
•Do not operate the High Pressure Washer if it has
been dropped or damaged in any manner. Always
have damage repaired before using your High
Pressure Washer.
•Spray only in daylight.
•Do not use accessory attachments that are not
recommended by the manufacturer. Use of such
attachments may be hazardous.
•Always wear safety glasses or eye shields when
starting and while using your High Pressure Was-
her.
•Dress properly. Do not operate High Pressure
Washer when barefoot or wearing open sandals.
Wear only solid shoes with good traction when
spraying.
•Keep your eyes and mind on your High Pressure
Washer and the area being sprayed. Do not let
other interests distract you.
•Never direct discharge of material toward bystan-
ders nor allow anyone near the High Pressure
Washer while you are spraying.
•Keep all safety devices in place and working.
LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.
IT MEANS – ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED
GROUNDING INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER
PROTECTION
To comply with the National Electrical Code (NFPA
70), and to provide additional protection from the risk
of electric shock, this pressure washer should only
be connected to a receptacle that is protected by a
ground fault circuit interrupter (GFCI).
Danger:
Improper connection of the equipment-groun-
ding conductor can result in electrocution. Check
with a qualified electrician or our service person
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the machine if it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.
EXTENSION CORDS
Use only extension cords that are intended for out-
door use. These extension cords are identified by a
marking“Acceptableforusewithoutdoorappliances;
store indoors while not in use”. Use only extension
cords having an electrical rating not less than the
rating of the machine. Do not use damaged extensi-
on cords. Examine extension cord before using and
replace if damaged. Do not abuse extension cord
and do not yank on any cord to disconnect. Keep
cord away from heat and sharp edges. Always dis-
connect the extension cord from the receptacle be-
fore disconnecting the unit from the extension cord.

3
CONGRATULATIONS onyourpurchaseofaSears
Craftsman high pressure washer. It has been desig-
ned, engineered and manufactured to give you the
best possible dependability and performance.
Should you experience any problems you cannot
easily remedy, please contact your nearest Sears
Service Center /Department. Sears has competent,
well trained technicians and the proper tools to
service or repair this unit.
Please read and retain this manual. The instructions
willenableyoutoassembleandmaintain your sprayer
properly. Always observe the “SAFETY RULES”.
MODEL NUMBER: 559.741710
SERIAL NUMBER: ________________
DATE OF PURCHASE: ________________
THE MODEL AND SERIAL NUMBERS WILL BE
FOUND ON A DECAL ATTACHED TO THE
HIGH PRESSURE WASHER.
YOU SHOULD RECORD BOTH SERIAL NUM-
BER AND DATE OF PURCHASE AND KEEP IN
A SAFE PLACE FOR FUTURE REFERENCE.
PRODUCT SPECIFICATIONS
HORSEPOWER 2 HP
VOLTAGE 120 V
1~60 Hz
AMP. RATING 13 A
OUTLET PRESSURE 1100 psi
FLOW RATE 1.95 gpm
DETERGENT INTAKE 0.2 gpm
WATER SUPPLY TEMPERATURE MAX. 104 °F
SUCTION HEIGHT with cold water (50 °F) 3 ft.
LENGTH 11.8 in
WIDTH 6.5 in
HEIGHT 16.3 in
WEIGHT (without accessories) 20 lbs
CUSTOMER RESPONSIBILITIES
•Read and observe the safety rules.
•Follow a regular schedule in maintaining, caring
for, and using your High Pressure Washer.
•Follow the instructions under "Customer Respon-
sibilities" and "Storage" sections of this Owner´s
Manual.
ONE YEAR LIMITED WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER
For one year from the date of purchase, when this Craftsman High Pressure Washer is maintained an operated
according to the instructions in the owner’s manual, Sears will repair, free of charge, any defect in material and
workmanship.
If this Craftsman High Pressure Washer is used for commercial purposes, this warranty applies for only 90 days
from the date of purchase. If this Pressure Washer is used for rental purposes, this warranty applies for only
30 days from the date of purchase.
This warranty does not cover:
•Expendable items which become worn during normal use.
•Repairs necessary because of operator abuse or negligence,including bent crankshafts and the failure to
maintain the equipment according to the instructions contained in the owner´s manual.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CARFTSMAN HIGH PRESSURE WASHER TO THE
NEAREST SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE
THE PRODUCT IS IN USE IN THE UNITED STATES.
This warranty gives your specific legal rights, and you may also have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., D/817 WA, Hoffman Estates, IL. 60179

4
SAFETY RULES .................................................... 2
GROUNDING INSTRUCTIONS ............................ 2
PRODUCT SPECIFICATIONS .............................. 3
WARRANTY ........................................................... 3
TABLE OF CONTENTS ........................................ 4
INDEX .................................................................... 4
ACCESSORIES ..................................................... 5
PACKING LIST ...................................................... 5
ASSEMBLY ............................................................ 6
OPERATION .......................................................... 8
CUSTOMER RESPONSIBILITIES ..................... 10
SERVICE AND ADJUSTMENTS ........................ 10
STORAGE ............................................................ 11
TROUBLE - SHOOTING ..................................... 12
REPAIR PARTS ................................................... 13
TABLE OF CONTENS
Accessories ............................................................ 5
After each use ...................................................... 10
Changeover nozzle ................................................ 9
Cleaning inlet filter ................................................ 10
Cleaning nozzle assembly ................................... 10
Cleaning solutions .................................................. 5
Cleaning tips .......................................................... 9
Customer responsibilities ....................................... 3
Detergent Application ............................................. 8
Detergent delivery ................................................ 10
Electrical connection .............................................. 7
Extension cords...................................................... 2
How to use your washer......................................... 8
How to set up your washer..................................... 7
Hose ..................................................................... 10
Know your High pressure Washer.......................... 6
Pressure wash / Rinse ........................................... 8
Product Specifications ............................................ 3
Protection against freezing ................................... 11
Pressure ............................................................... 10
Pump .................................................................... 10
Repair parts.......................................................... 10
Service and adjustments ...................................... 10
Storage................................................................. 11
Turning washer off ................................................. 8
Turning washer on ................................................. 8
Warranty................................................................. 3
Washing brush ....................................................... 9
Water supply .......................................................... 7
INDEX

5
ACCESSORIES
These accessories were available when this Pressure Washer was produced. They are also available
at most Sears retail outlets and service centers.
CLEANING SOLUTIONS
HOUSE WASH DECK WASH VEHICLE WASH DEGREASER
74273 74274 74275 74276
ACCESSORIES
ROTATING NOZZLE HOUSE WASHING WAND 18" EXTENSION WAND SUCTION
HOSE
ASSY
74173 74174 74175 74188
12 3 6 54
PACKING LIST
11 ea Washer assy
21 ea Gun with 25 ft pressure hose
31 ea Spray Wand
41 ea Extension
51 ea Brush
61 ea Garden Hose Connector assy
- Quick coupler male
- Female garden Hose Connector

6
ASSEMBLY
KNOW YOUR HIGH PRESSURE WASHER
READ THIS OWNER´S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER.
Compare the illustration with your High Pressure Washer to familiarize yourself with the locations of various
controls. Save this manual for future reference
2
5
4
1
6
3
12
10
7
9
11
8
1 ON/OFF switch
2 Electrical cord
3 Female garden hose connector
4 Quick coupler male
5 Water inlet with internal strainer
6 Detergent suction hose with filter
7 Safety lock
8 Washing brush
9 Extension
10 Spray wand with double nozzle
11 Trigger gun with high-pressure hose
12 High-pressure outlet
THIS PRESSURE WASHER MEETS UL STANDARDS

7
ASSEMBLY
Before using the unit, please note the following point:
Once unit has been removed from carton inspect it carefully for damages.
Should you discover any damages please notify your local SEARS RETAIL STORE.
ATTACHING TO WATER SUPPLY
• The garden hose (not supplied) must be at least
1/2inch inside diameter.
• The flow rate of the water supply must not fall below
2 GPM and the temperature must not exceed
104 °F.
IMPORTANT:
When connecting the water inlet to the water
supply mains, local regulations of your water
company must be observed. In some areas the
unit must not be connected directly to the puplic
drinking water supply. This is to ensure that
there is no feedback of detergents into the water
supply. Direct connection via receiver tank or
backflow preventer for example, is permitted.
The washer is not designed
for suction of liquids containing such solvents
as gasoline, paint
thinners, oil, acids, etc.
• Water can also be drawn from a standing water
supply such as a lake or a drum by means of
suction.
- When drawing water from a lake or drum, you
mustuse a suction hose with filter(
notsupplied).
- Remove the garden hose connector as this is
not used for suction operation.
- Connect the suction hose to the water inlet
connection.
IMPORTANT:
FOR NON PRESSURE WATER SOURCES
Do not exeed 36" elevation between pressure
washer and water supply and always use an inlet
filter or pump damage will occur.
HOW TO SET UP YOUR WASHER
• Push the spray wand into the trigger
gun against the spring tension and turn
it as far as the stop. The spray wand
must lock into position.
• Push the extension onto the double
nozzle so that the mark on the extension lines up
with the high pressure mark on the nozzle.
• Screw the high-pressure hose to the high-pressure
outlet.
• Screw quick coupler male to the water inlet.
• Screw garden hose connector to your garden hose.
• Now connect the garden hose with the quick cou-
pling to the water inlet.
• Screw the other end to the water faucet.
• Turn the water faucet on full force.
ELECTRICAL CONNECTION
The Sears Craftsman 1100 operates on 120 volt
electricity. Before plugging unit in, please ensure the
following.
• The power socket being used must be protected by
a 15 A or 20 A time-delay fuse.
• When using an extension cord observe the speci-
fications below. The unit will not operate with small
gauge extension cords.
Cable length Wire gauge
up to 25 ft. 14/3 AWG
25 to 50 ft. 12/3 AWG
IMPORTANT:
Always unwind cord completely.
Never leave coiled.
• Insert the plug into the grounded electrical outlet.

8
OPERATION
HOW TO USE YOUR WASHER
Pressure washer are a helpful tool designed to clean
almost any type of surface in two easy steps.
•First, the application of an appropriate detergent/
solvent solution to penetrate and loosen the grime.
The detergent is applied at low pressure to avoid
splashing, overspray and waste. The solution is left
on for 3-5 minutes to allow it to work.
•Second, the prepared surface is pressure washed
and rinsed clean.
DETERGENT APPLICATION
- Mix detergent solution in accordance with usage
instructions.
- PH value of the solution must be between 4 and 12.
- Place the end of detergent siphoning tube in deter-
gent solution.
- Hook up water supply.
- Twistnozzle(see Fig. page 9) to select low pressure
operation.
- Start washer and apply detergent on dry surface,
starting from the bottom and working up.
Note: Detergents are most effective when
applied to a dry surface.
- Cover only enough surface so that it does not dry
before washing / rinsing.
Note: Run clean water through the machine to
flush after spraying detergent.
DO NOT USE:
•BLEACHANDOTHER CORROSIVE CHEMICALS
•LIQUIDS CONTAINING SOLVENTS (IE. PAINT
THINNERS, GASOLINE, OIL)
•CHLORINE PRODUCTS
•TRI-SODIUM PHOSPHATE PRODUCTS
•AMMONIA PRODUCTS
•ACID-BASED PRODUCTS
PRESSURE WASH / RINSE
- Hook up water supply.
- Twist nozzle (see Fig. page 9) to select high
pressure operation.
Note: Detergent solution will not flow when in
the high pressure mode.
- Start washer and work from the top of the surface
down.
- The pressure washer is most effective when the tip
of the wand is held 6 to 24 inches from the surface
being cleaned.
TURNING WASHER ON
IMPORTANT:
You must never run this power washer unless it
is properly connected to a water supply or per-
mament damage may result.
- Connect to water supply and turn water on.
- Accuate gun trigger and purge lines of air.
- With gun off, switch power on.
Note: When you release the gun´s trigger
during operation, the bypass valve
opens, the water is returned to the suction
side of the pump and is recirculated.
TURNING WASHER OFF
IMPORTANT:
Turn washer off if not cleaning for more than
5 minutes to prevent damage.
- Switch power to off.
- Disconnect electrical cord.
- Disconnect water supply.
- Lock gun trigger for storage.

9
O P E R A T I O N
CHANGEOVER NOZZLE
• It is possible to work with a high pressure or a low
pressure jet. The symbol of the choosen jet form is
on the upper side of the changeover nozzle.
• Changing the jet form is only possible with the
trigger gun closed.
- Release trigger.
- Turn changeover nozzle 90° to alter pressure of
the water jet.
Note: Detergents can only be syphoned at low
pressure.
WASHING BRUSH
Use the washing brush to clean at low pressure to
remove dirt and road film. The brush can be used
with or without detergent.
To attach:
- Push the washing brush into the trigger gun
against the spring tension and turn it as far as the
stop.
- The washing brush must lock into position.
CLEANING TIPS
- For best results, the high-pressure lance should be
held between 6" - 24" away from the surface being
cleaned. Holding the wand too close to the surface
may damage the object being cleaned. On the
other hand, if the lance is too far away, optimum
cleaning results will not be achieved. it´s always
best to test the surface first to see if damage occurs
when the lance is held too close.
- When cleaning car tires, the nozzle should be held
at least 6" from the surface to avoid damage.
- Apply detergent at low pressure from the bottom
up and pressure wash at high pressure from the
top down.
- Always apply detergent to a dry surface and allow
1-3 minutes dwell time.
- To be environmentally safe,
•cleaning engines is only recommended where a
suitable oil seperator is provided.
•clean facades, terraces and garden equipment
with the high-pressure jet alone, without cleaning
agent.
Note: With special accessories (not included)
it can also be used for such jobs as
removing rust and paint, for cleaning
pipes, for pumping water and for
applying plant protection chemicals.
These items are avaiable from most
SEARS RETAIL OUTLETS.

10
CUSTOMER RESPONSIBILITIES
CLEANING INLET FILTER
The water inlet to the washer is protected by a filter
which should be checked and cleaned if it is found to
be dirty.
- Disconnect water inlet hose.
- Pull out internal filter.
- Clean filter.
- Reinstall filter.
CLEANING NOZZLE ASSEMBLY
- Disconnect the spray wand from the trigger gun.
- Remove dirt from nozzle bore with needle and
rinse with water from nozzle end.
- Reinstall
The warranty on this pressure washer does not cover
items that have been subjected to operator abuse or
negligent. To review full value from the warranty, the
operator must maintain the pressure washer as
instructed below.
AFTER EACH USE
•Flush detergent siphoning tube with fresh water.
•Disconnect water inlet hose and inspect / clean the
inlet filter.
•Clean nozzle assembly.
•Wipe hose, cord assembly unit to remove dirt, oil
etc.
No adjustments should be made to any parts that are sealed.
SERVICE AND ADJUSTMENTS
PRESSURE
The pressure is not adjustable.
PUMP
The pump is sealed and does not require any
lubrication.
HOSE
Replace leaking fittings and hose. Do not attempt to
repair, as they are designed to carry high pressure.
DETERGENT DELIVERY
The flow rate is set at 0.2 GPH and is not adjustable.
REPAIR PARTS
IMPORTANT:
The use of other than original spare parts could
lead to faults and even to serious accidents if
such parts are not properly manufactured or if
they do not exactly replace the original part.
If only original spare parts are used, you can be sure
that your unit will also work safely and without trouble
in the future.
For replacement parts information and ordering call
1-800-366-7278.
Before carrying out maintenance work, disconnect the plug from the electrical
power supply, and shut off the water supply.

11
PROTECTION AGAINST FREEZING
The cleaner will be severely damaged if it is stored
in a location where the temperature falls below
freezing point without its first being emptied of water
or flushed through with 50 % Anti-freeze solution.
The best protection against freezing is to store the
cleaner and the accessories (high-pressure hose,
trigger gun, spray lance) in a room where the tempe-
rature will not fall to the freezing point.
To empty the cleaner
· Disconnect the cleaner from the water supply.
· Disconnect the HP hose from the cleaner.
· The water will drain out.
A cleaner that may have frozen up should first be
thawed before it is put back into use as otherwise
damage may be caused.
Flushing with Anti-freeze solution
If the cleaner is to be out of operation for any length
of time, it is advisable to flush it through with a
glysantine solution as this provides a certain degree
of protection against corrosion. A solution of 50 %
Anti-freeze, 50 % water is pumped through the
cleaner.
STORAGE
HIGH-PRESSURE HOSE
Particular care should be paid to the hoses.
All high-pressure hoses must comply with
the safety regulations and be marked with
their working pressure, date of manufacture
and name of the maker.
High-pressure hoses must not be kinked,
twisted, crushed or damaged in any other
way. Damaged high-pressure hoses may
burstand arethereforedangerous andshould
be replaced without delay.
It is extremely dangerous to use high-pres-
sure hoses of low durability or that have
been inexpertly repaired and so you should
onlyusehigh-pressurehosesthathavebeen
tested and marked.
Original high-pressure hoses meet these
safety requirements.

12
T R O U B L E - S H O O T I N G
Fault Cause Remedy
Machine will not
start
- No electrical power
- Motor overheats
- Electrical defect
- Check power cord, plug, electric outlet or breaker
- Allow motor to cool down and switch on again with
ON/OFF switch
- Have machine repaired by authorized service
Machine does not
come up to
pressure
- Pump is sucking air
- Strainer is blocked
- Pump not bled to remove air
- Pump or relief valve defective
- Check garden hose and water connection,
turn on water supply
- Clean strainer
- Switch OFF machine, press trigger of gun,
switch ON machine while pressing trigger;
repeat if necessary
- Have machine repaired by authorized service
Water jet irregular - Nozzle clogged
- Water supply inadequate
- Safety valve incorrectly set
- Clean nozzle
- Check to see that water supply is on full force or
use stationary water source.
- Have machine repaired by authorized service
No intake of
detergent
- Nozzle in improper position
- Suction filter clogged
- Nozzle clogged
- Set nozzle to low pressure position
- Clean filter in suction nozzle
- Clean nozzle

13
REPAIR PARTS
2.883-251.0
6.362-422.0
6.362-422.0
6.414-384.0
CRAFTSMAN 1100
1.903-880 USA
6.414-277.0
4.775-186.0
6.389-562.0
2.883-254.0
4.760-241.0
5.762-105.0
3/94
5.394-365.0
6.388-576.0
6.389-716.0

14
SERVICE NOTES

15
SERVICE NOTES

OWNER’S
MANUAL
MODEL NO.
559.741710
HOW TO ORDER
REPAIR PARTS
SEARS, ROEBUCK and Co., Hoffman Estates, IL 60179 U.S.A.
5.956-138.0 Ä 9091 6/94
2 HP, 13 AMP, 120 V, AC, ELECTRIC
HIGH PRESSURE WASHER
Each High Pressure Washer has its own model number.
The model number for your High Pressure Washer will be found
on a decal attached to the back of the High Pressure Washer
housing.
All parts listed here in may be ordered through Sears, Roebuck
and Co. Service Centers and most Retail Stores.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
•PRODUCT - Pressure Washer
•MODEL NUMBER - 559.741710
•PART NUMBER
•PART DESCRIPTION
Your Sears merchandise has added value when you consider
that Sears has service units nationwide staffed with Sears trained
technicians.. professional technicians specifically trained on
Sears products, having the parts, tools and the equipment to
insure that we meet our pledge to you, we service what we sell.