Warranty.................................... 2
SafetyRules............................... 2-3
Unpacking.................................. 3
Assembly................................. 3-4
Installation................................. 4-5
Operation................................. 5-8
Maintenance............................... 8-9
Troubleshooting............................. 10
PartsIllustrationandList................... 12-13
EspaScl................................. 14-22
FULL ONE YEAR WARRANTY
If this product fails due to a defect in material or work-
manship within one year from the date of purchase,
Sears willat itsoption repair or replace it free of
charge. Contact your nearest Sears Service Center
(1-800-4-MY-HOME) to arrange for productrepair, or
return this productto place of purchase for replace-
ment.
If this product is used for commercial or rental purpos-
es, this warranty will apply for 90 days from the date of
purchase,
This warranty applies only while this product is used in
the United States.
This warranty gives you specific legal rights and you
may also have other dghts which vary from state to
state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179
WARNING: For your own safety, read all of the
instructions and precautions before operating tool.
CAUTION: Always follow proper operating procedures
as defined in this manual even if you are familiar with
use of this or similar tools. Remember that being care-
less for even a fraction of a second can result in severe
personal injury.
BE PREPARED FOR JOB
•Wear proper apparel. Do not wear loose clothing,
gloves, neckties, rings, bracelets or other jewelry
which may get caught in moving parts of machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States
ANSI Z87.1. Everyday glasses have only impact
resistant lenses. They are NOT safety glasses.
•Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools
when tired, intoxicatedor when taking medications
that cause drowsiness.
PREPARE WORK AREA FOR JOB
• Keep work area ciean. Cluttered work areas invite
accidents.
•Do not use power tools in dangerous environments.
Do not use powertools in damp or wet locations.Do
not expose powertools to rain.
•Work area should be properly lighted.
•Proper electrical receptacle shouldbe available for
tool.Three-prong plug should be plugged directly
intoproperly grounded, three-prong receptacle,
•Extension cords shouldhave a groundingprongand
the three wires of the extension cordshould be of
the correctgauge.
•Keep visitorsat a safe distance from work area.
•Keep children out of workplace. Make workshop
childproof.Use padlocks,master switches or remove
switchkeys to preventany unintentionaluse of
power tools.
TOOL SHOULD BE MAINTAINED
• Always unplug tool prior to inspection.
• Consult manual for specificmaintaining and adjust-
ing procedures.
•Keep tool lubricated and clean for safest operation.
•Remove adjustingtools. Form habit of checkingto
see that adjustingtools are removed before switch-
ingmachine on.
•Keep all parts in working order.Check to determine
thatthe guard or other parts willoperate properly
and perform their intendedfunction.
•Check for damaged parts. Check for alignmentof
moving parts, binding, breakage, mountingand any
other condition that may affect a tool'soperation.
• A guard or other part that is damaged shouldbe
properlyrepaired or replaced. Do not perform
makeshift repairs. (Use parts list provided to order
replacement parts.)
KNOW HOW TO USE TOOL
•Use righttool for job. Do not force tool or attachment
to do a job for which it was not designed.
•Disconnecttool when changing belt or abrasive disc.
•Avoid accidental start-up. Make sure that the switch
is in the "OFF" positionbefore plugging in.
•Do not force tool. It willwork most efficientlyat the
ratefor whichit was designed.
•Keep hands away from moving parts and sanding
surfaces.
• Never leave tool running unattended. Turn the power off
and do not leave tool until it comes to a complete stop.
• Do not overreach. Keep proper footing and balance.
©Sears, Roebuck and Co. 2
