Craftsman 315.116321 User manual

Owner's Manual
II:RRFTSMFIN I
113SHEET SANDER
Double Insulated
Model Nos.
315.116311
315.116321 ModelNo.315.116311
Save this manual for
future reference ModelNo.315.116321
_, CAUTION: Read and
follow all Safety Rules and
Operating Instructions before
first use of this product.
Customer Help Line: 1-800-932-3188
Sears Roebuck and Co., Hoffman Estates, IL 60179 USA
visit the Craftsman web page: www.sears.com/craftsman
972000-853
6-01
•Safety
•Features
•Assembly
•Operation
•Maintenance
•Parts List
US

TABLE OF CONTENTS
• General Safety Rules ................................................................................................................................................. 2-3
• Specific Safety Rules/Symbols .................................................................................................................................. 3-5
• Features ..................................................................................................................................................................... 5-6
• Assembly .................................................................................................................................................................... 7-9
• Operation .................................................................................................................................................................. 9-10
•Maintenance ................................................................................................................................................................ 11
• Accessories ................................................................................................................................................................. 11
• Exploded View And Repair Parts List .................................................................................................................... 14-15
• Parts Ordering / Service .............................................................................................................................................. 16
WARNING: Read and understand all instruc-
tions. Failure to follow all instructions listed
below, may result in.electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
•Keep your work area clean and well lit. Clut-
tered benches and dark areas invite accidents.
• Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or fumes.
•Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
Electrical Safety
•Double insulated tools are equipped with a
polarized plug (one blade is wider than the
other.) This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not
fit, contact aqualified electrician to install a
polarized outlet. Do not change the plug in
any way. Double insulation [] eliminates the
need for the three wire grounded power cord and
grounded power supply system.
•Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and refrigera-
tors. There is an increased risk of electric shock
if your body is grounded.
•Don't expose power tools to rain or wet condi-
tions. Water entering a power tool will increase
the risk of electric shock.
•Do not abuse the cord. Never use the cord to
carry the tools or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords imme-
diately. Damaged cords increase the risk of
electric shock.
•When operating a power tool outside, use an
outdoor extension cord marked "W-A" or "W".
These cords are rated for outdoor use and reduce
the risk of electric shock.
Personal Safety
•Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use tool while tired or under the influ-
ence of drugs, alcohol, or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
•Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught
in moving parts.
•Avoid accidental starting. Be sure switch is
off before plugging in. Carrying tools with your
finger on the switch or plugging in tools that have
the switch on invites accidents.

•Remove adjusting keys or wrenches before
turning the tool on. Awrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
•Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enables better control of the tool in unexpected
situations.
•Use safety equipment. Always wear eye pro-
tection. Dust mask, nonskid safety shoes, hard
hat, or hearing protection must be used for
appropriate conditions.
Tool Use and Care
•Use clamps or other practical way to secure
and support the workpiece to a stable plat-
form. Holding the work by hand or against your
body is unstable and may lead to loss of control.
•Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
•Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing the tool. Such preven-
tive safety measures reduce risk of starting the
tool accidentally.
Store idle tools out of reach of children and
other untrained persons. Tools are dangerous
in the hands of untrained users.
Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools, with
sharp cutting edges are less likely to bind and are
easier to control.
•Check for misalignment or binding of moving
parts, breakage of parts, and any other condi-
tion that may affect the tools operation. If
damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools.
Use only accessories that are recommended
by the manufacturer for your model. Accesso-
ries that may be suitable for one tool, may be-
come hazardous when used on another tool.
SERVICE
•Tool service must be performed only by
qualified repair personnel. Service or mainte-
nance performed by unqualified personnel could
result in a risk of injury.
•When servicing a tool, use only identical
replacement parts. Follow instructions in
Maintenance section of this manual. Use of
unauthorized parts or failure to follow Mainte-
nance Instructions may create a risk of electric
shock or injury.

Specific Safety Rules for Sanders
•Never use this or any power sander for wet
sanding or liquid polishing. Failure to comply
will increase the risk of electrical shock.
Additional Rules for Safe Operation
•Know your power tool. Read operator's
manual carefully. Learn its applications and
limitations, as well as the specific potential
hazards related to this tool. Following this rule
will reduce the risk of electric shock, fire, or
serious injury.
•Always wear safety glasses. Everyday eye-
glasses have only impact-resistant lenses;
they are NOT safety glasses. Following this rule
will reduce the risk of personal injury.
•Protect your lungs. Wear a face or dust mask
if the operation is dusty. Following this rule will
reduce the risk of personal injury.
• Protect your hearing. Wear hearing protection
during extended periods of operation. Follow-
ing this rule will reduce the risk of personal injury,
• Inspect tool cords periodically and, if dam-
aged, have repaired at your nearest Factory
Service Center or other Authorized Service
Organization. Constantly stay aware of cord
location. Following this rule will reduce the risk
of electric shock or fire.
•Check damaged parts. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its in-
tended function. Check for alignment of mov-
ing parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center.
Following this rule will reduce the risk of electric
shock, fire, or serious injury.
•Don't abuse cord. Never carry the tool by the
cord or yank it to disconnect it from the
receptacle. Keep cord away from heat, oil,
and sharp edges. Following this rule will reduce
the risk of electric shock or fire.
•Make sure your extension cord is in good
condition. When using an extension cord, be
sure to use one heavy enough to carry the
current your product will draw. A wire gage
size (A.W.G.) of at least 16 is recommended
for an extension cord 100 feet or less in
length. A cord exceeding 100 feet is not
recommended, if in doubt, use the next
heavier gage. The smaller the gage number,
the heavier the cord. An undersized cord will
cause a drop in line voltage resulting in loss of
power and overheating.
•Inspect for and remove all nails from lumber
before sanding. Following this rule will reduce the
risk of personal injury.
•Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or
any medication. Following this rule will reduce the
risk of electric shock, fire, or personal injury.
•Save these instructions. Refer tothem frequently
and use them to instruct others who may use
this tool. If you loan someone this tool, loan
them these instructions also. This will reduce the
risk of fire, shock, and injury.
AWARNING: Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known
to cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
•arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed
to filter out microscopic particles.

SYMBOLS
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
Alternating Current Type or a characteristic of current
no No Load Speed Rotational speed, at no load
Class II Construction Designates Double Insulated
Construction tools
.../min Revolutions or Reciprocation Per Minute Revolutions, strokes,
surface speed, orbits etc. per minute
,_1 k. Safety Alert Symbol Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
A)
B)
c)
D)
DEFINITIONS
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk offire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric
shock and personal injury.
NOTE: Advises you of information or instructionsvital to the operation or maintenance of the
equipment.

KNOW YOUR SANDER
See Figure 1.
Before attempting to use your sander, familiarize yourself
with all operating features and safety requirements.
Your sander is suitable for sanding with coarse, medium,
and fine grit sandpaper. It will produce a fine scratch free
finish when used to sand with the grain on wood surfaces.
It has also been designed so that sanding flush to corners
is possible.
APPLICATIONS
(Use only for the purposes listed below)
• Sanding on wood surfaces.
• Removing rust from and sanding steel surfaces.
SWITCH
This tool is equipped with a slide switch located on the
rear handle of your sander. To turn sander ON, slide the
switch forward as shown in Figure 1. Slide the switch
back to turn your sander OFF. Be sure sander switch is in
OFF position before connecting to power supply source.
DUSTLESS FEATURE (Model No. 315.116321 )
A dust bag assembly and a vacuum hose adapter is
included with your sander. Each provide a dust collection
system for your sander.
TOTURN
SANDERON
ELECTRICAL CONNECTION
Your sander has a precision built electric motor. It should
be connected to a power supply that is 120 volts, 60 Hz,
AC only (normal household current). Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
your tool does not operate when plugged into an outlet,
double-check the power supply.
PRODUCT SPECIFICATIONS
No Load Speed
Rating
Input
Model No. 315.116311
Model No. 315.116321
12,000 opm
120Volts, 60 Hz, AC only
1.8 Amperes
2.0 Amperes
Orbit Diameter 1/16 in.
Size of Paper 1/3 sheet
Paper Type
Dustless
Vacuum Hose Adaptor
Non-Adhesive Sandpaper
Adhesive Sandpaper
Model No. 315.116321 Only
Model No. 315.116321 Only
_k WARNING: Do not allow familiarity with your
sander to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
SWITCH SWITCH REAR
HANDLE
TO TURN
SANDEROFF
VACUUMHOSEADAPTER
(MODELNO.315.116321)
HANDLE
PLATEN
DUSTBAGASSEMBLY
(MODELNO.315.116321)
PAPERCLAMP LEVER Fig. 1
6

_ILWARNING: Your sander should never be con-
nected to power supply when you are assembling
parts, making adjustments, assembling or replacing
sandpaper, cleaning, or when not in use. Disconnect-
ing your sander will prevent accidental starting that
could cause serious personal injury.
INSTALLING SANDPAPER
See Figures 2 and 3.
The cushion on your sander gives you the option of using
either non-adhesive sandpaper that clamps to the platen; or
adhesive backed sandpaper with pressure sensitive adhe-
sive backing that sticks to the cushion.
INSTALLING NON-ADHESIVE SANDPAPER
See Figure 2.
Inspect sandpaper before installing. Do not use if broken
or defective.
• Unplug your sander.
,_L WARNING: Failure to unplug your sander could
result in accidental starting causing possible serious
personal injury.
SLOT
PAPERCLAMP
IN UNLOCKED
POSITION LEVER
NON-ADHESIVE
SANDPAPER
Fig. 2
Note: If your sander is Model No. 315.116321, removing the
dust bag assembly will make installing non-adhesive
sandpaper easier. Always remember to replace the dust
bag assembly before beginning operation.
• If replacing sandpaper, remove old sandpaper. To
remove sandpaper, a lever is located on each side of
your sander. Release paper clamps securing
sandpaper by lifting up on each lever and disengaging
from slot in platen.
•Insert end of new 1/3 sheet sandpaper approximately
1/2 inch under the front paper clamp.
• Lift up on lever on the left side of sander and lock into
slot on platen. Apply downward pressure to conform
sandpaper to platen.
• Wrap sandpaper around cushion and insert loose end
of sandpaper under the rear paper clamp. Fit
sandpaper against cushion as tight as possible.
• Lift up on lever located on right side of sander and
lock into slot in platen.
INSTALLING ADHESIVE SANDPAPER
See Figure 3.
• Unplug your sander.
_l, WARNING: Failure to unplug your sander could
result in accidental starting causing possible serious
personal injury.
• If replacing adhesive sandpaper, remove old
sandpaper by peeling it off cushion. If removing non-
adhesive sandpaper, release paper clamp by lifting up
on each lever, then remove sandpaper.
• Place levers back in locked position. Note: Always
check to make sure levers are in locked position
before turning sander on.
• Carefully peel adhesive backing from new 1/3 sheet
sandpaper.
• Position sandpaper, making sure front edge of
sandpaper is aligned with front edge of the cushion,
then carefully press sticky side of sandpaper on
cushion. Note: Sandpaper must be aligned with the
front edge of the cushion for proper functioning of the
flush sanding feature.
Note: It is recommended that you clean cushion occasion-
ally by brushing lightly with a small brush. Dust build-up
on cushion could cause sandpaper to not stick properly.
ADHESIVE
SANDPAPER
Fig. 3

ATTACHING DUST BAG ASSEMBLY
(Model No. 315.116321)
See Figure 4.
DUSTBAG
ADAPTER EXH
MODEL NO. 315.116321 Fig. 4
_, WARNING: To prevent the possibility of sanding
dust or foreign objects being thrown into your face or
eyes, never attempt to use your sander without the
dust bag assembly properly installed. Sanding dust or
foreign objects being thrown into your face could
result in possible serious personal injury.
• Unplug your sander.
_, WARNING: Failure to unplug your sander could
result in accidental starting causing possible serious
personal injury.
• Insert dust bag adapter into dust exhaust hole.
See Figure 4.
• Push in on adapter until raised notches on top and
bottom of adapter snap into grooves in dust exhaust
hole.
• Your sander is now ready for operation. Note: For more
efficient operation, empty dust bag when no more than
half full. This will permit the air to flow through the bag
better. Always empty and clean dust bag thoroughly
when finished sanding operation and before storing
sander.
TO REMOVE AND EMPTY DUST BAG
See Figure 5.
• Unplug your sander.
,_, WARNING: Failure to unplug your sander could
result in accidental starting causing possible serious
personal injury.
• Remove dust bag assembly from sander. To remove,
grasp adapter and pull straight out.
• Then remove dust bag from adapter as shown in
figure 5.
• Shake dust bag to empty.
• Place dust bag back on adapter.
• Attach dust bag assembly back on sander.
DUSTBAG
DUSTBAG
ADAPTER DUST
EXHAUSTHOLE
MODELNO. 315.116321 Fig. 5
8

ATTACHING VACUUM HOSE ADAPTER
(Model No. 315.116321)
See Figure 6.
A vacuum hose adapter is packed with sander Model No.
315.116321. This adapter easily attaches to your sander if
you decide to connect your sander to a vacuum.
• Unplug your sander.
_lh WARNING: Failure to unplug your sander could
result in accidental starting causing possible serious
personal injury.
TO ATTACH:
• Remove dust bag assembly from sander. To remove,
grasp adapter and pull straight out.
• Insert vacuum hose adapter into dust exhaust hole.
• Push in on adapter until raised notch on top and bottom
of adapter snap into groove in dust exhaust hole.
• Snugly attach vacuum hose adapter to vacuum hose.
• Connect vacuum hose to cleaner.
VACUUMHOSE
ADAPTER
_1, WARNING: Always wear safety goggles or safety
glasses with side shields when operating your
sander. Failure to do so could result in foreign
objects being thrown into your eyes, resulting in
possible serious injury. If the sanding operation is
dusty, also wear a face or dust mask.
PREPARING FOR OPERATION
,_ CAUTION: Be careful not to let hand cover the
your
air vents.
SANDING
Clamp or otherwise secure the work to prevent it from
moving under your sander.
WARNING: Unsecured work could be thrown
Htowards the operator causing injury.
Hold your sander in front and away from you, keeping it
clear of the workpiece. Start your sander by sliding the
switch button to the on position and letting the motor build
to its maximum speed. Gradually lower your sander on
the work with a slight forward movement. See Figure 7.
Move it slowly using forward and backward strokes.
RAISED
NOTCH
EXHAUSTHOLE
MODEL NO. 315.116321 Fig. 6
Fig. 7
DO not force. The weight of the unit supplies adequate
pressure, so let the sandpaper and sander do the work.
Applying additional pressure only slows the motor, rapidly
wears sandpaper and greatly reduces sander speed.
Excessive pressure will overload the motor causing
possible damage from motor overheating and can result in
inferior work. Any finish or resin on wood may soften from
the frictional heat. Do not allow sanding on one spot too
long as the sander's rapid action may remove too much
material, making the surface uneven.
9

SANDPAPER SELECTION
Selecting the correct size grit and type sandpaPer is an
extremely important step in achieving a high quality
sanded finish. Aluminum oxide, silicon carbide, and other
synthetic abrasives are best for power sanding. Natural
abrasives, such as flint and garnet are too soft for eco-
nomical use in power sanding.
In general, coarse grit will remove the most material and
finer grit will produce the best finish in all sanding opera-
tions. The condition of the su#ace to be sanded will
determine which grit will do the job. If the surface is rough,
start with a coarse grit and sand until the surface is
uniform. Medium grit may then be used to remove
scratches left by the coarser grit and finer grit used for
finishing of the surface. Always continue sanding with
each grit until surface is uniform.
Note: Do not use sander without sandpaper. Doing so
will damage the cushion.
& WARNING: Do not wear loose clothing or jewelry
when operating sander. They could get caught in
moving parts causing serious injury. Keep head away
from sander and sanding area. Hair could be drawn
into sander causing serious injury.
ORBITAL MOTION
See Figure 8.
Orbital motion is ideal for fast cutting action when
removing old finishes, smoothing rough wood, cutting
stock down to required dimensions, or for finishing
surfaces to be painted. As shown in figure 8, the
sandpaper moves in tiny circles at a very high speed,
allowing the sander to move easily.
ORBITALMOTION
Fig. 8
Flush sanding can be performed with your sander. See
Figure 9. Every side except the rear of your sander allows
flush sanding in corners. Always remove sander from
workpiece before turning your sander off.
Fig. 9
REMOVING SANDPAPER BEFORE STORAGE
Do not store your sander with pressure sensitive adhesive
sandpaper installed. Heat generated from sanding causes
the pressure sensitive adhesive to flow and form a tight
bond between the cushion and sandpaper.
Removing the sandpaper soon after you have finished a
sanding operation avoids letting the adhesive set up. If the
sandpaper is left on the cushion for an extended period of
time after use, the adhesive will set up and cause the
sandpaper to become difficult to remove.
It may also tear when removing. When this situation
occurs, it becomes difficult to clean the cushion for the
next piece of sandpaper.
Note: If you forget to remove the sandpaper after a
sanding operation, sand for a few minutes to soften the
adhesive backing before attempting to remove sandpaper.
10

_k WARNING: When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create ahazard or cause product damage.
GENERAL
All parts represent an important part of the double
insulation system and should be serviced only by a
qualified Sears service technician.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
,_ WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
It has been found that electric tools are subject to
accelerated wear and possible premature failure when
they are used on fiberglass boats, sports cars, wallboard,
spackling compounds, or plaster. The chips and grindings
from these materials are highly abrasive to electric tool
parts such as bearings, brushes, commutators, etc.
Consequently, it is not recommended that this tool be
used for extended work on any fiberglass material,
wallboard, spackling compounds, or plaster. During any
use on these materials it is extremely important that the
tool is cleaned frequently by blowing with an air jet.
EXTENSION CORDS
The use of any extension cord will cause some loss of
power. To keep the loss to a minimum and to prevent tool
from overheating, use an extension cord that is heavy
enough to carry the current the tool will draw.
Awire gage size (A.W.G.) of at least 16 is recommended
for an extension cord 100 feet or less in length. When
working outdoors, use an extension cord that is suitable
for outdoor use. The cord's jacket will be marked WA.
,_ CAUTION: Keep extension cords away from the
sanding area and position the cord so that it will not
get caught on lumber, tools, etc., during sanding.
,_ WARNING: Check extension cords before each
use. If damaged replace immediately. Never use tool
with a damaged cord since touching the damaged
area could cause electrical shock resulting in serious
injury.
Extension cords suitable for use with your sander are
available at your nearest Sears Retail Store.
,_ WARNING: Always wear safety goggles or safety
glasses with side shields during power tool operation
or when blowing dust. If operation is dusty, also wear
a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of the
unit under normal operating conditions. Therefore, no
further lubrication is required.
The following recommended accessories are currently available at Sears Retail Stores.
NON LOADING ALUMINUM OXIDE
ADHESIVE BACKED (3-2/3 in. x 7-1/8 in.)
Extra Fine
Fine
Medium
Coarse
ALUMINUM OXIDE SHEETS
(3-2/3 in. x 9 in.)
Fine
Medium
Coarse
_IL WARNING: The use of attachments or accessories not listed might be hazardous.
,_ WARNING:
The operation of any sander can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or star_dard safety glasses with side shields, available at Sears
Retail Stores.
11

WARRANTY
FULL ONE YEAR WARRANTY ON CRAFTSMAN SANDER MODEL NO. 315.116311
If this CRRFTJ;MRN Sander fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO
THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will replace it, free of charge.
If this CRRFTSMRN Sander is used for commercial or rental purposes, this warranty applies for only 90 days from the
date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
WARRANTY
FULL ONE YEAR WARRANTY ON CRAFTSMAN SANDER MODEL NO. 315.116321
If this/RRFTSMAN Sander fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO
THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair it, free of charge.
If this [RRFT.I;MRN Sander is used for commercial or rental purposes, this warranty applies for only 90 days from the
date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
SAVETHESEINSTRUCTIONS
NOTES:
12

NOTES:
13

CRAFTSMAN SANDER - MODEL NOS. 315.116311 AND 315.116321
SEE NOTE "A" PAGE 15
1
'2
10
12
I
I
3
4
I
7
'=' 8
4
6
14

ICRAFTSMAN SANDER - MODEL NOS. 315.116311 AND 315.116321
The model number will be found on a plate attached to the motor housing. Nways mention the model number
in all correspondence regarding your SANDER or when ordering repair parts.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS J
Key Part
No. Number
1 982588-001
982590-001
2 977308-001
977272-001
3 977265-001
4 977266-001
5 623019-004
6 977267-001
7 617966-028
8 977268-001
977268-002
9***
10 976967-002
11 989919-005
12 977270-001
972000-853
PARTS LIST
Description Quan.
Data Plate (Model No. 315.116311) ........................ 1
Data Plate (Model No. 315.116321 ) ........................ 1
Logo Plate (Model No, 315.116311) ....................... 1
Logo Plate (Model No. 315.116321) ....................... 1
Dust Shield (Model No. 315,116321 ) ...................... 1
Paper Clamp ............................................................ 2
Rubber Plug ............................................................. 1
Platen ....................................................................... 1
Screw (#8-10 x 1/2 in. Pan Hd.) .............................. 4
Cushion (Model No. 315.116321) ........................... 1
Cushion (Model No. 315.116311) ........................... 1
Sandpaper
Vacuum Hose Adapter (Model No. 315.116321) .... 1
Ball Bearing ............................................................. 1
Dust Bag Assembly (Model No. 315.116321) ......... 1
Owner's Manual
NOTE: "A"- The assembly shown represents an important part of the Double Insulated System. To avoid
the possibility of alteration or damage to the system, service should be performed by your
nearest Sears Repair Center. Contact your nearest Sears Retail Store for Service Center
information.
* Standard Hardware Item - May Be Purchased Locally
*** Complete Assortment Available At Your Nearest Sears Retail Store
15

Get it fixed, at your home or ours!
For repair of major brand appliances in your own home...
no matter who made it, no matter who sold ifl
1-800-4-MY-HOME sMAnytime, day or night
(1-800-469-4663)
www.sears.com
To bring in products such as vacuums, lawn equipment and electronics
for repair, call for the location of your nearest Sears Parts & Repair Center.
1-800-488-1222 Anytime, day or night
www.sears.com
For the replacement parts, accessories and owner's manuals
that you need to do-it-yourself, call Sears PartsDirect sM!
1-800-366-PART 6a.m. - 11 p.m. CST,
(1-800-366-7278) 7 days a week
www.sears.com/partsdirect
To purchase or inquire about aSears Service Agreement:
1-800-827-6655
7 a.m. - 5 p.m. CST, Mon.- Sat.
Para pedir servicio de reparaci6n a domicilio,
y para ordenar piezas con entrega a domicilio:
1-888-SU-HOGAR s_
(1-888-784°6427)
Au Canada pour service en fran_ais:
1-877-LE-FOYER s_
ISEARS 1
HomeCentral_
(1-877-533-6937)
TM
®Registered Trademark /Trademark of Sears. Roebuck and Co
® Sears. Roebuck and Co. ® Mama Registrada /T_ Marca de F&'brica de Sears, Roebuck and Co.