,.odei 139.53758
3-Function Mini Transmitter Owners Manual
EC;,.O.rules prohibit adjustments toor modification of receiver and/or transmitter circuitry except for changing the code setting
and replacing transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Manufactured under 1or more of the following US. patents: RE29,525; 4,037,201;4,750,118;4.806,930
i,ll ii ,i
MATCH THE CODE IN NEW AND EXISTING TRANSMITTERS
Remove the cover screw in NEW transmitter. Turn case over to access code switches #1 through #9. Be careful not
to move circuit board components. Locate code switches inc_iginal transmitter(s), (Refer to illustration)_ Set code switches
in the 3_Function Mini Transmitter to the same positions as code switches in the original transmitter.
NOTE 1: Code switches #2 through #g in ALL transmitters used to operate a receiver must be sot to match. (Coda
switch #1 on 8 3-function transmitter Is neutral. Set it to ANY position. It will not affect the code selected.
NOTE 2: If the original transmltter(s) has only 7or 8 code switches, set code switches #8 and!or #9 to center
(0) position tn new transmitter.
o-_
JJ "0' "1 St_,ndard [I
3-Function 0:3 -.,_ Standard
i
I" 1 €2-9)
REPLACEMENT PARTS: Transmitter Housing Only (No circuit board) - 4tA3592; 12V Battery - 10A14
CHANGE THE CODE IN RECEIVER AND TRANSMITTER(S)
53000SR SERIES
0NITH RECEIVER 'SR' CODE BUTTON)
Garage Door Openers and Light Controls
(illustration A shows a garage door opener receiver)
Selec_ a traz_rni_ef
pushbuttonIo X
operatereceiver _ t_ wffr °u_ _L
Key Ring Push _ltons
Holder "S_' Indicator ....
CodeButton Light
Make sure all transmitters areset to matching codeswitch
positions as described above.
1o Press the 'SR' code button on your receiver (illt_tra-
tion A). The indicator light wilt turn ONe
2. STAND AWAYFROM DOOR and press the transmit-
ter's SELECTED PUSH BUTTON. The indicator light
will turn OFFand door will move.Code in receiver now
matches transmitter(s) code and will activatewhen the
selected transmitter push button is pressed,
NOTE: I! transmitter push button ts not pressed
within 30 seconds, the Indicator light will turn OFF.
Repeat 1 and 2,
To use the 3-Function Mtnl Transmitter with other
53000SR Serlse receivers: Select another transmitter
pushbutton tooperatee Light Controlor additional garage
door opener. Make sure all transmitters used to operate
receiver are set to the same cote (as described above).
Then repeal I and 2.
You can select adifferent transmitter push button tooper-
ate each device.
53000 SERIES
(WITH RECEIVER CODE SWITCHES)
Garage Door Openers and Light Controls
(illustration B shows a garage door opener receiver)
Push(_ulton Select a
transmitter
_PushButton pushbutton
f _ J (+)
Key Ring Push Button to operate
g Holder (O) receiver
IF_D WHT BLK Y_:L
codeswitch#1
1234_;678ii to positJortthe!
!ltltlMltl pushbur_on
CodeSwitch
#1
Makesure alltransmitters are set tomatching code switch
positionsas described above.
1, Select a transmitterpush buttonto operatethereceiver
as shown in Figure 13.
2, Set RECEIVER code switch #1 to match the position
of the transmitter push button selected. Refer to
illustration BeThen set remaining code switches in
receiver to match the transmitter(s) code switch
positions.
NOTE: If the receiverhas only 7 or 8 switches, sot
transmitter switch #8 and/or #g to (0).
Tousethe 3-FuncttonMlnl Transmitterwith other 53000
Series receivers: Set receiver code switch #1 to match
thepositionofanothertransmitterpushbutton. Then set
remaining code switches to match transmitter(s)code
switches,
Code switches #2 through #9 in all transmitters used
to operate the receiver MUST be set to matching
positions.
IJIIL,I,ll,_,Jll,llJ_Ui
©19g0,Sears Roebuck & Company
114Al160_._ All RlghfJiReserved Printed In Mexico
