Creative Structures Crossover L Instruction Manual

www.creativestructures.nl
Building instructions Crossover L
Version 2.1

Building instructions Crossover L
Page 1
www.creativestructures.nl
Pre-assemble the lower sub proles (4x)
Step 1:
Locking pin
Short version
CS-0105
2x
Securing ring
CS-0248
2x
Lower (short) sub prole
CS-0055
T-Connector Lower Right
Marked with “LR”
CS-0057
T-Connector Lower Left
Marked with “LL”
CS-0052
LL
LR
Curvature has to point downwards
!

Building instructions Crossover L
Page 2
www.creativestructures.nl
Pre-assemble the upper sub proles (4x)
Step 2:
Upper (long) sub prole
CS-0054
T-Connector Upper Right
Marked with “UR”
CS-0056
T-Connector Upper Left
Marked with “UL”
CS-0051
UL
UR
Locking pin
Short version
CS-0105
2x
Securing ring
CS-0248
2x
Curvature has to point downwards
!

Building instructions Crossover L
Page 3
www.creativestructures.nl
Pre-assemble the sub frame
Step 3:
Sub frame center
CS-0334
Secure all parts with locking pins (short version)
and securing rings
!
Joint has to point downwards
!
Sub frame beam
CS-0335
4x
Sub frame connector
CS-0336
4x

Building instructions Crossover L
Page 4
www.creativestructures.nl
Assemble frame body
Step 4: Secure all parts with locking pins (long version)
and securing rings
!
Main prole
CS-0049
X-connector
CS-0050
X-connector
CS-0050
Hooks have to point inwards
!
Main prole
CS-0049
Main prole
CS-0049

Building instructions Crossover L
Page 5
www.creativestructures.nl
Secure all parts with locking pins (long version)
and securing rings
!
Main prole
CS-0049
X-connector
CS-0050
X-connector
CS-0050

Building instructions Crossover L
Page 6
www.creativestructures.nl
Mount sub frame at frame body
Step 5:
Locking strip
CS-0337
4x
Securing ring
CS-0248
4x

Building instructions Crossover L
Page 7
www.creativestructures.nl
While building, the structure has to be lifted multiple times so that the assembly can easily be done on oor level.
The structure is designed for two lifting methods:
1. Lifting from below (for example with a traverse lift) by using the subframe. Requirements lifting device:
• minimum lifting height: 6 meter
• minimum save working load: 300kg
2. Lifting from above (for example with a crane) by using lifting slings (2 meter, 1000 KG) and the hooks of the
X-connectors
Lifting:
Note: this lifting methode requires more
height for building
!

Building instructions Crossover L
Page 8
www.creativestructures.nl
Mount the rst end of the main cables
Step 6:
Main cable
4x per X-connector
CS-0086

Building instructions Crossover L
Page 9
www.creativestructures.nl
Step 7:
Mount the rst level of main proles
Main prole
CS-0049
8x
Secure all parts with locking pins (long version)
and securing rings
!

Building instructions Crossover L
Page 10
www.creativestructures.nl
Step 8:
Mount the upper sub proles (4x) Secure all parts with locking pins (long version)
and securing rings
!
UL
UR
Curvature sub proles has to point inwards
!

Building instructions Crossover L
Page 11
www.creativestructures.nl
Step 9:
Mount the second end of the 8 inner main cables

Building instructions Crossover L
Page 12
www.creativestructures.nl
Step 10:
Mount the rst end of the tensioning cables
Tensioning cable
CS-0234
8x

Building instructions Crossover L
Page 13
www.creativestructures.nl
Step 11:
Mount the second level of main proles Secure all parts with locking pins (long version)
and securing rings
!
Main prole
CS-0049
8x

Building instructions Crossover L
Page 14
www.creativestructures.nl
Step 12:
Mount the lower sub proles (4x) Secure all parts with locking pins (long version)
and securing rings
!
LL
LR
Curvature sub proles has to point inwards
!

Building instructions Crossover L
Page 15
www.creativestructures.nl
Step 13:
Mount the second end of the 8 remaining main cables cables

Building instructions Crossover L
Page 16
www.creativestructures.nl
Step 14:
Mount the last level of main proles Secure all parts with locking pins (long version)
and securing rings
!
Main prole
CS-0049
8x

Building instructions Crossover L
Page 17
www.creativestructures.nl
Step 15:
Mount the feet (4x) Secure all parts with locking pins (long version)
and securing rings
!
Foot connector Left
CS-0058
Foot connector Right
CS-0108
Anchor slide
CS-0099
Anchor support
CS-0148
Hooks have to point to the inside of the structure
!

Building instructions Crossover L
Page 18
www.creativestructures.nl
Step 16:
Mount the positioning cables
Positioning cable
CS-0235
4x
The positioning cables are used to secure an acurate distance between the feet.
After mounting the positioning cables the structure can be placed on its feet
Pull the legs of the structure outwards to put the positioning cables under tension
!

Building instructions Crossover L
Page 19
www.creativestructures.nl
Step 17:
Anchor the structure
For the different anchoring options and instructions see
the anchoring guide
!
After anchoring, the positioning cables can be removed.
In stormy conditions the positioning cables have to be
mounted to provide extra stability to the structure
!