Creative Structures Lounger M Instruction Manual

www.creativestructures.nl
Building instructions Lounger M
Version 1.0

Building instructions Lounger M
Page 1
www.creativestructures.nl
Pre-assemble the leg-proles (4x)
Step 1:
Leg prole
CS-0287
Check position of cut outs
!
Leg connector
CS-0346
Foot
CS-0292
Secure the parts with locking pins and securing rings
!

Building instructions Lounger M
Page 2
www.creativestructures.nl
Unfold the structure
Step 2:

Building instructions Lounger M
Page 3
www.creativestructures.nl
Place the cover on the structure and fold back the whole unit
Step 3:
Align the seams of the cover with the structure

Building instructions Lounger M
Page 4
www.creativestructures.nl
Attach the inner loops of the cover to the structure ends with H-shackles
The cover has to be mounted in folde state because in that case there is no tension on the cover corners.
The nal tension on the cover can be adjusted by choosing a neighbouring mounting hole.
Be sure that all four shackles are mounted in a hole with the same number
The loops at the outside of the cover can be pulled downwards to make the installation easier.
Step 4:
1
2
3
4
5
H-shackle Inner loop
Mounting holes
Outer loop

Building instructions Lounger M
Page 5
www.creativestructures.nl
Unfold the structure
Step 5:

Building instructions Lounger M
Page 6
www.creativestructures.nl
Tension the cover
Step 6:
Unlock Hook in Pull the lever

Building instructions Lounger M
Page 7
www.creativestructures.nl
Close the lever
When it is not possible to close the lever by hand, repeat
step 4 and choose a lower hole number for the H-shackles
!
When the cover is not tensioned enough, repeat step 4
and choose a higher hole number for the H-shackles
!

Building instructions Lounger M
Page 8
www.creativestructures.nl
Connect the rst end of the main cables to the cover frame (8x)
Step 7:
Main cable
CS-0298
Connect the rst end of the tension cables to the cover frame (4x)
Step 8:
Tension cable
CS-0345

Building instructions Lounger M
Page 9
www.creativestructures.nl
Lift the cover and mount the rst leg prole
Step 9:
A tripot support can be used to keep up the structure
and make the assembly easier
Slide the connecting fork over the two pins of the
cover frame until it totally supports the lower pin

Building instructions Lounger M
Page 10
www.creativestructures.nl
Connect the second end of the two matching main cables to the leg prole
Step 10:
The cables can be connected easi-
ly by lifting the corners of the cover
frame or supporting them with a tripot

Building instructions Lounger M
Page 11
www.creativestructures.nl
Connect the second end of the tension cable to the leg prole
Step 11:
The pelican hook should be closed easily. If not, extend the tension cable
by turning the pelican hooks counter clockwise

Building instructions Lounger M
Page 12
www.creativestructures.nl
Repeat step 9 - 11 for the second, third and fourth leg prole
Step 12:
Stabilize the structure by shortening the four tension cables
By tensioning the tension cables, all main cables are getting tensioned and the structure will get rigidity
Step 13:

Building instructions Lounger M
Page 13
www.creativestructures.nl
Anchor the structure
Step 14:
For the different anchoring options and instructions see
the anchoring guide
!

Building instructions Lounger M
Page 14
www.creativestructures.nl
Attach the connecting lashing hooks to the four side panel corners
Step 15:

Building instructions Lounger M
Page 15
www.creativestructures.nl
Hook in the side panel by using the two upper lashing hooks
Step 16:

Building instructions Lounger M
Page 16
www.creativestructures.nl
Connect the two lower lashing hooks
Step 17:
Tension the side panel by tensioning the four lashing hooks
Step 18:

Building instructions Lounger M
Page 17
www.creativestructures.nl
Drape the upper and lower ap of the side panel to the outside of the structure
Step 19:
The individual side panels can be connected to each other with the zippers

Building instructions Lounger M
Page 18
www.creativestructures.nl
Install the cover connection gutter (if desired)
Step 19:
Hook in the gutter using the six hooks
on the gutter
Tension the gutter with the elastic
cords on both ends
Connection gutter
CS-0394

Building instructions Lounger M
Page 19
www.creativestructures.nl
Install the side panel connection panel by using the zippers (if desired)
Step 20:
Connection panel
CS-0396