Creator CRT-310-NR01 User manual

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 1/16
CRT-310-NR01 Motorized Card Reader Manual
CREATOR (CHINA) TECH CO., LTD
Add: 2F, M-10 Building, Center Area, Hi-tech Industrial Park, Shenzhen, China
TEL: [phone]
FAX: [phone]
Email：[e-mail]
Http://www.china-creator.com/

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 2/16
Revision record
Version Date Content
V1 2013.12.09 First time release

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 3/16
● Welcome to use Creator’s product
● Please read the manual carefully before you use our product
Basic component：
1-----------Bezel (optional)
2-----------Pulley and card read parts
3-----------RS-232 communication interface connector
4-----------4PIN interface connector of power supply
Warn ：Morn than 15V is prohibited，it may cause reader damaged！！
3
2
1
4

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 4/16
Content
1、Product Overview ..................................................................................................................................... 6
2、Specification ........................................................................................................................................... 6
3、Technical Parameter ............................................................................................................................... 6
4、Sensor location instruction： ........................................................................................................... 9
7、Card moving status： ........................................................................................................................... 10
8、Operation mode ....................................................................................................................................... 10
8.1 Card insertion of activities： ..................................................................................................... 10
1) ICRW automatically reads the magnetic stripe card after the card enters in，then moves
the card to the inner specific position；........................................................................................ 10
2）ICRW moves the card to the inner specific position after the card entries from rear terminal.
......................................................................................................................................................................... 10
8.2 Read magnetic stripe card： ........................................................................................................... 10
ICRW automatically reads the magnetic stripe card after the card enters in，save the data
in RAM，waiting to upload the data after receiving the relevant command； ........................ 10
8.3 Read IC card：moving to IC card operation position，and begin to operate after successfully
move（including auto-test card type）............................................................................................... 10
8.4 Read contactless IC card: the card staying in ICRW at IC card operation position, RF
operation is allowed at this moment................................................................................................... 10
8.5 Abnormal cards handling： ............................................................................................................... 10
1）Abnormal cards means that the size and shape are different from ISO standard cards；
......................................................................................................................................................................... 10
2）ICRW automatically removes the card to the front of entrance if it judges the card is
abnormal as the card enters into the machine；.............................................................................. 10
3）Recharging of abnormal card，if ICRW checks the abnormal card existed，there are 2 ways
to handle as following: ........................................................................................................................... 10
① For the long length card，executing reset command，ICRW removes the card to the front；
......................................................................................................................................................................... 10
② For the shorter card，nowhere the card is in machine or at front entrance，executing reset
command“ejecting the card backwards” ，meantime to insert a normal card , ICRW will
discharge them together backwards....................................................................................................... 10
8.6 Power down handling： ........................................................................................................................11
1）The power cable is combined with 4- wire（red-yellow-2 black） ，12V-red/yellow，GND-black，
the yellow-black in middle set is prepared for backup power supply，connecting to back-up
capacitor for card ejecting when power down；.................................................................................11
2）Once main power down，there is a backup power for preparing work，the ICRW will start
to run its power down mode after 1 second，if the card is inside of the ICRW, eject card
or not decided by set of PD parameter; ICRW responses negative to any command before the
power supply recovered（error word“power down protected state”） ；.................................11
3）If the main power is recovered (≥11V)，the ICRW returns to previous state (before power
down) by executing reset command. ........................................................................................................11
8.7 Error handling ......................................................................................................................................11
Once ICRW occupied with the error of blocks，it’s necessary to clear the error sign by sending
the reset command, after that it’s possible to execute other commands.(The details referred
to protocol) ..................................................................................................................................................11
9、power supply connection illustrating..........................................................................................................11
10、Preventive and Maintenance ............................................................................................................. 13
11、Cautions for use ................................................................................................................................. 13

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 5/16
12、Other relevant documents ................................................................................................................. 15
1) DLL：CRT-310-NR01 DLL Specification .PDF.................................................................................... 15
2) DLL SOURCE CODE：DLL sample source code...................................................................................... 15
3) Communication Protocol：CRT-310-NR01 Protocol .PDF................................................................ 15
13、Structure dimensions ......................................................................................................................... 15

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 6/16
1、Product Overview
CRT-310-NR01 is a motorized card reader with card captured/ ejected and 3-card in one function.
Product main feature：
1） 3-card in one：Mag-card read, IC card read & write, contactless IC card read & write.
2） Electromagnetic controlled shutter, the commands support Mag/switch controlled open.
3） Motorized card captured and ejected with the function of card retrieved at rear end.
4） Installed dimension and location of bezel holes are completely compatible with SANKYO
ICT-3K7-3R6940（height is difference）；
5） Communication protocol, fault tolerant and card processing are same as SANKYO
ICT-3K7-3R6940；
6） High reliability and durability；
7） CE and EMC certification；
8） Power traced and power down protected
9） PBOC3.0 and EMV4.1 certified（contact IC card）；
10）ICRW life: at least 600,000 cycles（one cycle is card in and out）；
11）Optional parts： PSAM board
2、Specification
1) With functions of Magnetic stripe card read, contact & contactless card read & write,
the cards should be compliant of related standard，refer to technical parameters.
2) With the functions of automatically card captured, controlling of in/out/retrieved.
3) Both front & rear insertion of card, move and clear broken card in reader.
4) RS232 interface
5) With multi-function of fault tolerant and special maintenance including process of
abnormal cards and power down etc.
3、Technical Parameter
1) Power supply DC 12V±5%
2) Current consumption Idle current： less than 150 mA
Peak current： less than 1500 mA
3) Speed Around 300mm/s
4) Interface RS232

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 7/16
5) Card specification Width:53.92～54.18 mm， Length：85.47～85.90 mm
Thickness: 0.4mm～1.2mm（ex-work:0.8mm）
6) Net Mass Approximately 410g（not including accessories and package）
7) Amount dimension Refer to structure outline drawing
8) Performance of reading Mag-Card Pass the test of the standard/Q card（TC-JI 15% BB
30%SI，TC-A 30% weaken Mag-Card）
9) Reliability A．Vibration： frequency： 5～50Hz；Acceleration：2m/s2
（0.2G）；direction
and time：X，Y，Z directions, each 15 minutes； amplitude：2mm；
no functional failure at A
B．Shock： 294m/s2（30G），11ms， each of X，Y，Z directions once，no
functional failure at B（ICRW without package）
10) Life Transport：1000,000 pass Min（one card pass is a forward and a reverse）
Magnetic head：read card 600,000 times Min
Downward press device and contact for IC card：300,000 on/off Min
11) Power down mode voltage≤10V，time≥50 ms
12) Error rate Mag-card：normal condition (15～25℃，35～60%RH)，less than 1 time per
1,000 times reading standard card； note: standard card except man made
error.
IC card：less than once error per 1,000 times，（except Q card）.
note：above IC cards are standard card
Contactless IC card：reading & writing error less than once per 10,000
times ,--note：Standard card
13) Warped card Average abnormal height is less than 2mm
14) MTBF More than 100,000 hours（only electric components）
note：250 times/day，25 days/Month，300 hours/Month
15) Environment operation: 0℃～50℃, 0～90% RH ( no condensing )
storage: -25℃～80℃, 0～95% RH ( no condensing )
normal condition：15～25℃，35～60%RH
16）On-line download support IAP on-line download
17）RoHS standard RoHS standard compliant
18）IC card standard ISO7816-1，2，3，4/EMV 4.1 L1/PBOC 3.0 L1
（AT24C01、24C02、……、24C256；SLE4442、SLE4428；CPU T=0/T=1）
19）Contactless IC card ISO14443-3 (Mifare one： S50、S70、UL etc)

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 8/16
ISO14443-4（TYPE A CPU： mifare plus， mifare desfire etc）
（TYPE B CPU）
20）Magnetic stripe card standard
Physical feather: ISO7810 and 7811
Card dimension: ISO7810ID-1-magnetic stripe card standard
Embossed card：ISO7811-1 and ISO7811-3
Record format：ISO7811-2、ISO7811-4、ISO7811-5 and ISO7811-6 standard

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 9/16
4、Sensor location instruction：

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 10/16
7、Card moving status：
1. The card holding position at front side
2. Inner position
3. IC card operation position
8、Operation mode
8.1 Card insertion of activities：
1) ICRW automatically reads the magnetic stripe card after the card enters in，then moves
the card to the inner specific position；
2）ICRW moves the card to the inner specific position after the card entries from rear terminal.
8.2 Read magnetic stripe card：
ICRW automatically reads the magnetic stripe card after the card enters in，save the data
in RAM，waiting to upload the data after receiving the relevant command；
8.3 Read IC card：moving to IC card operation position，and begin to operate after successfully
move（including auto-test card type）.
8.4 Read contactless IC card: the card staying in ICRW at IC card operation position, RF operation
is allowed at this moment.
8.5 Abnormal cards handling：
1）Abnormal cards means that the size and shape are different from ISO standard cards；
2）ICRW automatically removes the card to the front of entrance if it judges the card is
abnormal as the card enters into the machine；
3）Recharging of abnormal card，if ICRW checks the abnormal card existed，there are 2 ways
to handle as following:
① For the long length card，executing reset command，ICRW removes the card to the front；
② For the shorter card，nowhere the card is in machine or at front entrance，executing
reset command“ejecting the card backwards” ，meantime to insert a normal card ,
ICRW will discharge them together backwards.
1
2 3

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 11/16
8.6 Power down handling：
1）The power cable is combined with 4- wire（red-yellow-2 black） ，12V-red/yellow，GND-black，
the yellow-black in middle set is prepared for backup power supply，connecting to back-up
capacitor for card ejecting when power down；
2）Once main power down，there is a backup power for preparing work，the ICRW will start
to run its power down mode after 1 second，if the card is inside of the ICRW, eject card
or not decided by set of PD parameter; ICRW responses negative to any command before the
power supply recovered（error word“power down protected state”） ；
3）If the main power is recovered (≥11V)，the ICRW returns to previous state (before power
down) by executing reset command.
8.7 Error handling
Once ICRW occupied with the error of blocks，it’s necessary to clear the error sign by sending
the reset command, after that it’s possible to execute other commands.(The details referred
to protocol)
9、power supply connection illustrating
CRT-310-NR01 with two methods：
1） Single main power connection（shown as following picture 1）
Red & yellow mixed wire connected to ＋12V，black wire connected to －12V
2）Main power + back-up capacitor (for card ejected after power down) connection method
（shown as following picture 2）
Red connected to ＋12V，black connected to －12V，
Yellow wire connected to back-up capacitor ＋ terminal，black wire connected to back
-up capacitor － terminal.

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 12/16
CB4
22000uF/50V
CB3
22000uF/50V
CB2
22000uF/50V
CB1
22000uF/50V
P2
接黄线
P3
接黑线
1
2
3
4
J3
CON4
P1
接红线
P4
接黑线
P2
接黄线
P3
接黑线
1
2
3
4
J3
CON4
主电源
接红线
P4
接黑线
图1：无掉电弹卡功能接线
图2：后备电容组掉电弹卡功能接线
主电源

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 13/16
10、Preventive and Maintenance
The reader should be maintained after the appropriate interval of use:
1）When the transportation roller is dirt, please use cleaning card with alcohol
2）Dip the cleaning card into alcohol and execute card transportation command to clean the internal area.
3）Periodic maintenance:
For sensor, magnetic head and IC contact, suggest a maintenance every 2,000 times
①Sensor maintenance: Connect reader first and operate DEMO to query & check sensor status. In the
initial status (No card inside), the all status of sensor are “OFF”, and if there is a sensor status show
as ”ON”, the maintenance of this sensor group is needed.
②IC contact maintenance: If any dirt is founded on the IC contact, please use cleaning card with alcohol to
clean. Use method: After insert cleaning card, please execute auto test card type function to clean the IC
contact.
③Roller maintenance: Use card transportation command and cleaning card.
④Magnetic head maintenance: Use card transportation command and cleaning card
11、Cautions for use
1）Cut the power for ICRW before start to repair
2）Prohibit to plug out serial port in electrified condition.
3）Grease contamination is prohibited
4）Suggest DC12V/3Apower supply. Prohibit to access to power surpass 15V
5）Plug out power first than serial port

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 14/16
6）Insertion direction for IC card: See the following picture. Shown as following (Picture 3)
图四 IC 卡的进卡方向
Picture 3 IC card entry direction
7）Insertion direction for Magnetic card: Magnetic strip is on the right side of reader; please refer to the
following picture 4
Picture 4 Magnetic stripe card entry direction
Mag-stripes face downwards to
lower side, locate at right side
on the card
Right side
IC position

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 15/16
12、Other relevant documents
1) DLL：CRT-310-NR01 DLL Specification .PDF
2) DLL SOURCE CODE：DLL sample source code
3) Communication Protocol：CRT-310-NR01 Protocol .PDF
13、Structure dimensions

Model No. CRT-310-NR01
SPECIFICATION Date 2013/12/9
Ver. 1.0
Motorized Card Reader Page 16/16