Cree XLamp MT Series User manual

soldering & handling
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are
registered trademarks and the Cree logo is a trademark of Cree, Inc. Other trademarks, product and company names are the property of their respective
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
CLD-AP75 REV 5G
Cree®XLamp®MT Family and MK Family LEDs
INTRODUCTION
This application note applies to XLamp®MT Family and MK
Family LEDs, which have order codes in the following formats.
MTxxxx-xx-xxxx-xxxxxxxxx
MKxxxx-xx-xxxx-xxxxxxxxx
This application note explains how XLamp MT Family and MK
Family LEDs and assemblies containing these LEDs should be
handled during manufacturing. Please read the entire document
to understand how to properly handle XLamp MT Family and MK
Family LEDs.
TABLE OF CONTENTS
Handling XLamp®MT Family and MK Family LEDs................... 2
Circuit Board Preparation & Layouts........................................... 4
Case Temperature (Ts) Measurement Point............................... 5
Notes on Soldering XLamp®MT Family and MK Family LEDs.. 6
Moisture Sensitivity ..................................................................... 7
Low Temperature Operation........................................................ 7
XLamp® MT Family and MK Family LED Reow Soldering
Characteristics ............................................................................. 8
Chemicals & Conformal Coatings............................................... 9
Assembly Storage & Handling................................................... 10
Tape and Reel............................................................................. 11
Packaging & Labels ................................................................... 12

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
2
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
HANDLING XLAMP®MT FAMILY AND MK FAMILY LEDS
Manual Handling
Use tweezers to grab XLamp MT Family or MK Family LEDs at the base. Do not touch the lens with the tweezers. Do not touch the lens
with ngers. Do not push on the lens.
Do not apply more than 1000 g of shear force directly onto the lens. Excessive force on the lens could damage the LED.
Cree recommends the following at all times when handling XLamp MT Family or MK Family LEDs or assemblies containing these LEDs:
• Avoid putting mechanical stress on the LED lens.
• Never touch the optical surface with ngers or sharp objects. The LED lens surface could be soiled or damaged, which would affect
the optical performance of the LED.
• Cree recommends always handling XLamp MT Family or MK Family LEDs with appropriate ESD grounding.
• Cree recommends handling XLamp MT Family or MK Family LEDs wearing clean, lint-free gloves.
X
WRONG
P
CORRECT

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
3
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
Whenever possible, Cree recommends the use of the following pick and place tool to remove XLamp MT Family LEDs from the factory
tape and reel packaging.
All measurements are ±.13 mm unless otherwise indicated.
Whenever possible, Cree recommends the use of the following pick and place tool to remove XLamp MK Family LEDs from the factory
tape and reel packaging.
All measurements are ±.13 mm unless otherwise indicated.
HANDLING XLAMP®MT FAMILY AND MK FAMILY LEDS - CONTINUED

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
4
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
CIRCUIT BOARD PREPARATION & LAYOUTS
Printed circuit boards (PCBs) should be prepared and/or cleaned according to the manufacturer’s specications before placing or
soldering XLamp MT Family or MK Family LEDs onto the PCB. The diagrams below show the recommended PCB solder pad layout for
XLamp MT Family LEDs.
All measurements are ±.13 mm unless otherwise indicated.
M T- G
MT-G2
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
9.113
9.113
.650
4.85
±.25
R4.100
8.90
.950
.500
6.000
8.90
8.900
8.900
6.000
.950
.950
.500
.500
6.198
.889
1.090
1.905
1.072
1.905
8.839
.889
.937
.937
1.722
3.175
3.175
1.090
8.072
1/19.000
C
2610-00011
TIGER 9191 OUTLINE
10/8/10D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A INITIAL RELEASE DC 10/8/10
B CHANGED SOLDER PAD VIEW DC 1/11/11
C ADDED STENCIL VIEW DC 2/18/11
RECOMMENDED PC BOARD SOLDER PAD RECOMMENDED STENCIL PATTERN
Recommended PCB Solder Pad Recommended Stencil Pattern
(Shaded Area Is Open)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ±.5°
.XXX± .25
.XX ±.75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ±.25
.XXX±.125
X° ± .5°
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
8.90
8.90
6.00
.95
.95
.50
.50
9.11
9.11
R4.10
.65
4.85
±.25
8.90
REF.
8.90
REF.
.95
.50
6.00
8.90
8.90
8.90
8.90
.30
.95 .95
1.35 .25
.58
1.35
1.23
.25
1/19.000
B
2610-00025
MT-G2 OUTLINE
5/14/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A INITIAL RELEASE DC 5/14/12
BADDED ALTERNATE VIEW/UPDATED STENCIL
DC 8/19/15
RECOMMENDED PC BOARD SOLDER PAD RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
PRIMARY
ALTERNATIVE
8.90
REF.
8.90
REF.
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ±.5°
.XXX±.25
.XX ±.75
.X ±1.5
FOR SHEET METAL PARTS ONLY
.XX ±.25
.XXX± .125
X° ±.5°
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
8.90
8.90
6.00
.95
.95
.50
.50
9.11
9.11
R4.10
.65
4.85
±.25
8.90
REF.
8.90
REF.
.95
.50
6.00
8.90
8.90
8.90
8.90
.30
.95 .95
1.35 .25
.58
1.35
1.23
.25
1/19.000
B
2610-00025
MT-G2 OUTLINE
5/14/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A INITIAL RELEASE DC 5/14/12
B ADDED ALTERNATE VIEW/UPDATED STENCIL
DC 8/19/15
RECOMMENDED PC BOARD SOLDER PAD RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE ±.13MM UNLESS OTHERWISE NOTED
PRIMARY
ALTERNATIVE
8.90
REF.
8.90
REF.
Recommended PCB Solder Pad Recommended Stencil Pattern
(Shaded Area Is Open)

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
5
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
The diagram below shows the recommended PCB solder pad layout for XLamp MK Family LEDs.
All measurements are ±.13 mm unless otherwise indicated.
CASE TEMPERATURE (TS) MEASUREMENT POINT
XLamp MT Family and MK Family LED case temperature (Ts) should be measured on the PCB surface, as close to the LED’s thermal pad
as possible. This measurement point is shown in the pictures below.
MT-G MT-G2 MK-R MK-R2
It is not required to use a solder footprint for the thermal pad that is larger than the XLamp MT Family or MK Family LED itself. In testing,
Cree has found such a solder pad to have insignicant impact on the resulting Tsmeasurement.
Recommended PCB Solder Pad
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
7.00
7.00
.73
4.08
R3.25
6.70
6.76
REF.
6.76
6.70
3.90
.70
.70
6.76
6.70
1.24
1.29
.25
.70
.25
1.29
6.76
REF.
6.70
REF.
6.70
6.76
.70 .70
3.90
.70
1/111.000
E
2610-00031
MKR Marketing Spec
11/7/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B VIEWS SHOW LATEST REVISION DC 8/5/13
D NOTCH IS ADDED TO BACKSIDE DC 7/7/14
E UPDATED ALL VIEWS DC 6/19/15
RECOMMENDED STENCIL PATTERN
SHADED AREA IS OPENING
RECOMMENDED PCB SOLDER PAD
PRIMARY ALTERNATIVE ALTERNATIVE
Recommended Stencil Pattern
(Shaded Area Is Open)
CIRCUIT BOARD PREPARATION & LAYOUTS - CONTINUED

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
6
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
NOTES ON SOLDERING XLAMP®MT FAMILY AND MK FAMILY LEDS
XLamp MT Family and MK Family LEDs are designed to be reow soldered to a PCB. Reow soldering may be done by a reow oven or
by placing the PCB on a hotplate and following the reow soldering prole listed on the previous page.
Do not wave solder XLamp MT Family or MK Family LEDs. Do not hand solder XLamp MT Family or MK Family LEDs.
Solder Paste Type
Cree strongly recommends using “no clean” solder paste with XLamp MT Family or MK Family LEDs so that cleaning the PCB after reow
soldering is not required. Cree uses Kester®R276 solder paste internally.
Cree recommends the following solder paste compositions: SnAgCu (tin/silver/copper) and SnAg (tin/silver).
Solder Paste Thickness
The choice of solder and the application method will dictate the specic amount of solder. For the most consistent results, an automated
dispensing system or a solder stencil printer is recommended. Cree has seen positive results using solder thickness that results in a 4-mil
(102-μm) bond line, i.e., the solder joint thickness after reow soldering.
P
CORRECT
P
CORRECT
X
WRONG
P
CORRECT
X
WRONG

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
7
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
After Soldering
After soldering, allow XLamp MT Family and MK Family LEDs to return to room temperature before subsequent handling. Premature
handling of the device, especially around the lens, could result in damage to the LED.
Cree recommends verifying the solder process by checking the consistency of the solder bond of several trial PCBs after reow. After
shearing selected devices from the circuit board the solder should appear completely re-owed (no solder grains evident). The solder
areas should show minimum evidence of voids on the backside of the package and the PCB.
Cleaning PCBs After Soldering
Cree recommends using “no clean” solder paste so that ux cleaning is not necessary after reow soldering. If PCB cleaning is necessary,
Cree recommends the use of isopropyl alcohol (IPA).
Do not use ultrasonic cleaning.
MOISTURE SENSITIVITY
Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering.
Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity.
Once the MBP is opened, XLamp MT Family and MK Family LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have
unlimited oor life in conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of storage condition, Cree recommends sealing any
unsoldered LEDs in the original MBP.
LOW TEMPERATURE OPERATION
The minimum operating temperature of these XLamp LED components is -40 °C. To maximize lifetime, Cree recommends avoiding
applications where the lamps are cycled on and off more than 10,000 cycles at temperatures below 0°C.
NOTES ON SOLDERING XLAMP®MT FAMILY AND MK FAMILY LEDS - CONTINUED

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
8
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
XLAMP®MT FAMILY AND MK FAMILY LED REFLOW SOLDERING CHARACTERISTICS
In testing, Cree has found XLamp MT Family and MK Family LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed
below. As a general guideline, Cree recommends that users follow the recommended soldering prole provided by the manufacturer of the
solder paste used, and therefore it is the lamp or luminaire manufacturer’s responsibility to determine applicable soldering requirements.
Note that this general guideline may not apply to all PCB designs and congurations of reow soldering equipment.
Profile Feature Lead-Free Solder
Average Ramp-Up Rate (Tsmax to Tp) 1.2°C/second
Preheat: Temperature Min (Tsmin) 120 °C
Preheat: Temperature Max (Tsmax)170 °C
Preheat: Time (tsmin to tsmax) 65-150 seconds
Time Maintained Above: Temperature (TL)217 °C
Time Maintained Above: Time (tL) 45-90 seconds
Peak/Classication Temperature (Tp) 235 - 245 °C
Time Within 5°C of Actual Peak Temperature (tp) 20-40 seconds
Ramp-Down Rate 1 - 6 °C/second
Time 25°C to Peak Temperature 4 minutes max.
Note: All temperatures refer to topside of the package, measured on the package body surface.
IPC/JEDEC J-STD-020C
TP
TL
Temperature
Time
t 25˚C to Peak
Preheat
ts
tS
tP
25
Ramp-down
Ramp-up
Critical Zone
TL to TP
Tsmax
Tsmin

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
9
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
CHEMICALS & CONFORMAL COATINGS
Below are representative lists of chemicals and materials to be used or avoided in LED manufacturing activities. For a complete and
current list of recommended chemicals, conformal coatings and harmful chemicals consult Cree’s Chemical Compatibility Application
Note. The video at www.youtube.com/watch?v=t24bf9D_1SA illustrates the process Cree has developed for testing the compatibility of
chemicals and materials with LEDs. You should also consult your regional Cree Field Applications Engineer.
Recommended Cleaning Solutions
Cree has found the following chemicals to be safe to use with XLamp MT Family and MK Family LEDs.
• Water
• Isopropyl alcohol (IPA)
Chemicals Tested as Harmful
In general, subject to the specics in Cree’s Chemical Compatibility Application Note, Cree has found certain chemicals to be harmful to
XLamp MT Family and MK Family LEDs. Cree recommends not using these chemicals anywhere in an LED system containing XLamp MT
Family and MK Family LEDs. The fumes from even small amounts of the chemicals may damage the LEDs.
• Chemicals that might outgas aromatic hydrocarbons (e.g., toluene, benzene, xylene)
• Methyl acetate or ethyl acetate (i.e., nail polish remover)
• Cyanoacrylates (i.e., “Superglue”)
• Glycol ethers (including Radio Shack®Precision Electronics Cleaner - dipropylene glycol monomethyl ether)
• Formaldehyde or butadiene (including Ashland®PLIOBOND®adhesive)
Hermetically Sealing Luminaires
For proper LED operation and to avoid potential lumen depreciation and/or color shift, LEDs of all types must operate in an environment
that contains oxygen. Simply allowing the LEDs to ventilate to air is sufcient; no extraordinary measures are required. Hermetically
sealing LEDs in an enclosed space is not recommended.

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
10
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
ASSEMBLY STORAGE & HANDLING
Do not stack PCBs or assemblies containing XLamp MT Family or MK Family LEDs so that anything rests on the LED lens. Force applied
to the LED lens may result in the lens being damaged or displaced. PCBs or assemblies containing XLamp MT Family or MK Family LEDs
should be stacked in a way to allow at least 1 cm clearance above the LED lens.
Do not use bubble wrap directly on top of XLamp MT Family and MK Family LEDs. Force from the bubble wrap can potentially damage
the LED.
P
CORRECT
X
WRONG
P
CORRECT

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
11
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
TAPE AND REEL
All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard.
All dimensions in mm.
MT Family Carrier Tape
MK Family Carrier Tape
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
Trailer
160mm (min) of
empty pockets
sealed with tape
(15 pockets min.)
Loaded Pockets
(500 Lamps)
12±.1
5.25
16
+.3
-.0
1.75
±.10
4±.10
Leader
400mm (min) of
empty pockets
sealed with tape
(35 pockets min.)
9.4
1/13.000
B
2402-00016
MTG LOADING SPEC
--
--
----
----
1/28/11D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A Initial Release DC
1/28/11
B
Added missing sprocket holes
DDS
10/17/11
END START
User Feed Direction
CATHODE SIDE
ANODE SIDE
1.5± .1
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
Trailer
160mm (min) of
empty pockets
sealed with tape
(15 pockets min.)
Loaded Pockets
(500 Lamps)
12±.1
5.25
16
+.3
-.0
1.75
±.10
4±.10
Leader
400mm (min) of
empty pockets
sealed with tape
(35 pockets min.)
9.4
1/13.000
B
2402-00016
MTG LOADING SPEC
--
--
----
----
1/28/11D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A Initial Release DC
1/28/11
B
Added missing sprocket holes
DDS
10/17/11
END START
User Feed Direction
CATHODE SIDE
ANODE SIDE
1.5± .1
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
Trailer
180mm (min) of
empty pockets
sealed with tape
(15 pockets min.)
Loaded Pockets
(1000 Lamps)
12±.1
4.31
16
+.3
-.0
1.75
±.10
4±.10
Leader
420mm (min) of
empty pockets
sealed with tape
(35 pockets min.)
7.4
0.36
"13
13mm
1/13.000
A
2402-00025
MKR LOADING SPEC
--
--
----
----
12/7/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A Initial Release DC 12/7/12
END START
User Feed Direction
CATHODE SIDE
ANODE SIDE
User Feed Direction
1.5± .1
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
X° ± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTANED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
SURFACE FINISH:
63
330
+.25
-.75
12.4
+1.0
-.5
MEASURED AT EDGE
16.4
+0.2
.0
MEASURED AT HUB
12.4
+.2
.0
MEASURED AT HUB
±.213.1
1.9±.4
±.421
60° 60°
1/10.500
A
2400-00009
REEL, 13" X 12MM, 3 PIECE SNAP
-
ANTI-STATIC HIPS
----
----
09/29/09D. CRONIN
2400-00009
INDEX QTY ITEM COMMENTS
1 1 2400-00009-CORE
2 2 2400-00009-REEL
REVISONS
REV DESCRIPTION BY DATE APP'D
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
X° ± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTANED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
SURFACE FINISH:
63
330
+.25
-.75
12.4
+1.0
-.5
MEASURED AT EDGE
16.4
+0.2
.0
MEASURED AT HUB
12.4
+.2
.0
MEASURED AT HUB
±.213.1
1.9±.4
±.421
60° 60°
1/10.500
A
2400-00009
REEL, 13" X 12MM, 3 PIECE SNAP
-
ANTI-STATIC HIPS
----
----
09/29/09D. CRONIN
2400-00009
INDEX QTY ITEM COMMENTS
1 1 2400-00009-CORE
2 2 2400-00009-REEL
REVISONS
REV DESCRIPTION BY DATE APP'D
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
X° ± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTANED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
SURFACE FINISH:
63
330
+.25
-.75
12.4
+1.0
-.5
MEASURED AT EDGE
16.4
+0.2
.0
MEASURED AT HUB
12.4
+.2
.0
MEASURED AT HUB
±.213.1
1.9±.4
±.421
60° 60°
1/10.500
A
2400-00009
REEL, 13" X 12MM, 3 PIECE SNAP
-
ANTI-STATIC HIPS
----
----
09/29/09D. CRONIN
2400-00009
INDEX QTY ITEM COMMENTS
1 1 2400-00009-CORE
2 2 2400-00009-REEL
REVISONS
REV DESCRIPTION BY DATE APP'D

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®and XLamp®are registered trademarks and the Cree logo is a trademark
of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specic product and/or vendor endorsement, sponsorship or association. This
document is provided for informational purposes only and is not a warranty or a specication. For product specications, please see the data sheets available at www.cree.com.
12
XLamp®mT FamiLy & mK FamiLy LED SoLDEring & HanDLing
PACKAGING & LABELS
The diagrams below show the packaging and labels Cree uses to ship XLamp MT Family and MK Family LEDs. XLamp MT Family and MK
Family LEDs are shipped in tape loaded on a reel. Each box contains only one reel in a moisture barrier bag.
Label with Cree Bin
Code, Qty, Lot # Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Dessicant
(inside bag)
Humidity Indicator
Card (inside bag)
Patent Label
Label with Customer Order
Code, Qty, Reel ID, PO #
Patent Label
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
Unpackaged Reel
Packaged Reel
Boxed Reel
This manual suits for next models
5
Table of contents
Other Cree Work Light manuals
Popular Work Light manuals by other brands

Larson Electronics
Larson Electronics GNM-LEDWL-25W Instruction guide

Luminar
Luminar Luminar Work 4.5 Watt/120 Volt 45 Bulb Led Work... Owner's manual & safety instructions

MEANDRE TECHNOLOGIE
MEANDRE TECHNOLOGIE MEANDRE 1.0 Operating instructions, Technical sheet

Makita
Makita DML813 instruction manual

Milwaukee
Milwaukee 49-24-0155 Operator's manual

nedis
nedis WIFILX51RGB quick start guide