Creedmoor Deluxe Cart Conversion Kit User manual

Creedmoor Deluxe Cart Conversion Kit
(Shown with optional stool)
Congratulations on the purchase of your new Creedmoor Deluxe Cart Conversion Kit.
Before you begin lay out all the parts as shown in Figures 1, 2 and 3 to ensure you received all necessary
parts.
Tools needed for assembly: Allen wrench (included), 7/16th” wrench and socket, ¾” wrench and socket,
10mm wrench.

Figure (1)
Figure (2)
Figure (3)
Step 1: Assuming you already have
the stool, remove the crutch tips
from the narrower of the two stool
frames. This will/should be the back
of your cart once assembled.
A8
A3
A4
A7
A6R
A6L
A5
A12
A13
A11
A10
A9

Step 2: Once the crutch tips are
removed, measure 2 ½” from the
bottom and put a small mark in the
inside of the frame. This is where the
u-bolts will be positioned.
Step 3: Insert the u-bolts (A13) into
the two small aluminum pieces
(wheel anchors A8) that will be used
to attach the wheels.
Step 4: Attach each of the wheel
anchors so that the pieces are on the
outside portion of the frame and
facing away from the stool bag. Then
finger tighten the bolts. The u-bolt
should be covering the mark you
previously put on the stool frame 2
½” from the bottom.
Step 5: Without the washer, insert
the axle bolt (A12) into the wheel
through the outside of the wheel
(shallow end) with the threaded end
protruding to the inside. (The
shallow end is the outside of the
wheel).

Step 6: Attach the steel washer and
the nut.
Step 7: Using a ¾” wrench and socket
tighten the nut. The axle bolt should
still spin freely even after tightening
the nut.
Step 8: Assemble the lower portion
of the handle/frame using 4 of the
supplied allen screws (A10) and
wrench. Being countersunk the holes
for the screws are easily identifiable.

Step 9: Position the lower
handle/frame so the holes line up
with the axle mount holes on the
wheel anchors you previously
mounted to the stool frame.
Step 10: Using a ¾” socket attach the
axles to the wheel anchors and
tighten, then loosen ¼ turn.
Step 11: Place ¾” nut on inside of
axle and tighten. Frame should move
freely from wheel anchor.

Step 12: Assemble the upper handle
by attaching the handle to the two
notched aluminum bars. The notches
should be assembled to face the stool
bag. As with the lower handle the
screw holes are easily identifiable
being countersunk.
Step 13: Slide the cloth cart back
onto the upper handle with the
notches and the tag facing forward.
Step 14: Remove the hinge bolts
from your stool frame and replace
with them with the longer ones
supplied with this conversion kit.
Prior to reassembly run the bolts
through the smaller holes in the two
lock bars, which should be the only
two remaining bars. Tighten nuts
only to the point there is a little
tension on the bar.

Step 15: Align and insert the locking
pins (A9) into the non-threaded holes
in the lock bar, the upper handle, and
the lower handle.
Step 16: Rotate the handle up to its
upright position, align the threaded
holes with the non-threaded hole in
the rifle rack hook, and insert the
large star knob.
Step 17: Using a 10mm wrench
tighten the nuts on the u-bolts
holding the wheel anchors in place.
Avoid over-tightening the nuts as it is
unnecessary and will crush the frame
tubing.

Step 18: Replace the crutch tips you
previously removed.
Optional Scope Stand Mount Instructions
Tools needed: 5mm allen wrench, 4mm allen wrench
Step 2: Remove one of
the wheels.
Step 1: Using the 5mm allen wrench
attach the scope clamp so that it’s
facing away from the stool bag.

Step 3: Separate the bar from the
frame and slide the scope stand
bracket over the bar.
Step 5: Place the 1” scope stand base
onto the mount making sure it’s
aligned with the upper scope clamp
adjusting the position of the mount if
necessary, then retighten the allen
screws.
Step 4: Reattach the bar and wheels,
then position the bracket near the
center of the bar and snug the allen
screws using the 4mm allen werench.