Hamilton/Buhl PLCAB4226E User manual

( Instructions continued on next page )
Instructions
Flat Panel TV Cart
Model #: PLCAB4226E
Warranty begins the date that the item ships out of our warehouse. Metal carts have a
limited lifetime warranty on all housing components; however, carts have a one year
warranty on any electrical/mechanical components.
Note: This unit is easier to assemble with two people.
Parts list
Qty. Description
1 Top shelf
4 Top legs
1 Bottom shelf section
2 Poles for supporting flat panel TV
2 Horizontal mount
1 Electrical bracket
1 Power cord
3 Screws and hex nuts (E)
Qty. Description
9 Set Phillips head bolt, washer and hex nut (I)
8 Set Screw and serrated nut (K)
2 Casters with brakes
2 Casters without brakes
2 Security screws for mounting the poles (F)
2 Security screw (G)
2 Hex head screw (H)
2 Set Pull out shelf
Tools required
L key
Adjustable wrench/pliers
Rubber mallet
4.
Insert two bolts, washer and nuts (see screw table I) into each leg
of table. Washer should be on the inside of leg. Tighten all bolts
and nuts.
Screw table
Some screws may have already been
screwed on the related parts.
2.
Insert top table section onto bottom section.
3.
Align corresponding holes of unit to obtain desired height.
1.
Insert top legs onto top shelf. Tighten top legs with screws,
washer and nuts (see screw table K) as shown.
PLCAB4226E
Horizontal mount
Pole
WARNING: Please keep
the TV mounting screws
A, B, C & D and the L keys
in a secure location as
they may be required for
use with the flat panel TV
at a later time.
PROP 65 WARNING: This product
contains the chemical known to the
State of California to cause cancer
and birth defects or other reproductive
harm.
!

7.
Insert the two
supporting poles
onto the holes
on the top shelf.
Wire holes can
face inside or
outside.
6 B.
Tighten the pull-out shelf
onto leg on both sides,
as shown.
9.
Tighten the two supporting poles onto the top shelf with two
security screws (see screw table F) as shown.
8.
Insert the two horizontal
mounts onto the
supporting poles. Note:
The mount with
adjustable screw (see
screw table H) should
go on the bottom. Screw
(see screw table G) the
top mount to desired
height from A to F. Adjust
the bottom mount height
according to the TV
screw position as shown.
11.
Use the appropriate security screws needed (M4, M5, M6 or M8,
see screw table A,B,C or D) to fasten the flat panel TV onto the
horizontal mounts as shown.
10.
Electrical bracket assembly instruction
A. Push power cord into cord winder bracket.
B. Attach electrical bracket to back side of top shelf with two nuts
and bolts (see screw table E). Tighten nuts and bolts securely.
Wrap the power cord around the bracket wings.
6 A. Pull-out shelf assembly instruction
Due to limited packaging space, pull-out shelf was
shortened. Adjust the pull-out shelf out to the maximum
inside width of the cart inside,as the pull-out shelf will be
installed on the inside part of the legs.
5.
Lay unit on floor. Insert casters with brakes into opposite
corner holes in the bottom of the unit. Insert other casters
into remaining holes of unit.
Top horizontal mount
Bottom horizontal mount
WARNING: Please keep the TV
mounting screws A, B, C & D and
the L keys in a secure location as
they may be required for use with
the flat panel TV at a later time.
If any parts or hardware are missing or damaged, Do Not Return
the unit to your dealer. Call the HamiltonBuhl help line at
[phone] for immediate parts replacement.
A Division of Vcom IMC
80 Little Falls Road, Fairfield, NJ 07004, USA
1-800-631-0868 • www.HamiltonBuhl.com