Crest Audio CC-SDC User manual

Model
CC-BLK
Designed & manufactured in the USA by:
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
Model
Name
CKS 100
CKS 200
CKS 400
CKS 800
CKS 800-2
CKS 1200-2
CKS 1600-2
Output Power
@8Ω/Ch.
50W
100W
200W
400W
400W
600W
800W
Model
Name
CKV 100
CKV 200
CKV 400
CKV 800
CKV 1600
CKV 2400
Output Power
@70.7V
50W
100W
200W
400W
800W
1200W
LISTED 8B42
COMMERCIAL
POWER
AMPLIFIER
120V~60 Hz 15A
Model
CC-SDC
Com
Out
In
+8 to +18VDC
240 mA Max Load
NEC
CLASS 2 ONLY
Sequential
Turn-On
CLASS 2
WIRING MAY
BE USED
Output
A
B
+
+
–
–
Signal
Ground
Lift
Jumper
Sequential Turn-On/Off
connection to other
amplifiers
Com
In
Out
+8 to +18VDC
20mA Max
Load
+
--
+
--
CC-SDC Sequential Turn-On/Off (STO); on-board power supply
Product Information
The CC-SDC Module fits in the Power/Output bay located on the rear
panel of Crest Audio CKS, CKV & CKX Series Power Processing
amplifiers. It provides Sequential Turn-On/Off (STO) capability for a
series of CKS, CKV & CKX amplifiers without the need for an external
VDC power source. The on-board supply provides power to twelve
other CKS, CKV & CKX amplifiers equipped with basic CC-STL, STO
modules.
Providing a simple closure across two terminals on the first amplifier in
the chain will initiate the turn-on or turn-off sequence. The CC-SDC
cannot be controlled or actuated via NexSys®. A three-position front
panel power switch is fitted to all CKS, CKV & CKX amplifiers. This
must be in the “Remote” position for the CC-SDC to initiate an STO
sequence.
Features:
• Provides external power for up to twelve CC-STL sequential turn-on functions
• Amplifier output terminals on barrier strip with 0.44" (11mm) screw spacing and 0.32" (8mm) lug spacing
• 5mm 4-pin Phoenix connector for sequential turn-on/off (STO) connection
• Signal chassis ground lift jumper
POWER/OUTPUT MODULE
FOR CKS, CKV & CKX SERIES
POWER PROCESSING AMPLIFIERS
Architects and Engineers Specifications - CC-SDC.
The module shall plug into a Crest Audio CKS or CKV Power Processing amplifier in the
Power/Output bay. The module shall contain an internal DC power supply to provide non-
NexSys initiated sequential turn-on/off capability for groups of CKS and/or CKV amplifiers.
A 5mm 4-pin Phoenix connector shall be provided to transmit the turn-on initiation voltage
signal.
A closure across two of the Phoenix connector terminals shall initiate the turn-on sequence.
The module shall provide outputs for both amp channels on barrier strip connectors and a
signal ground lift jumper. The module shall be designated the Crest Audio model CC-SDC.
CC-SDC connections
Power
Processing
Modules
USA-specification amplifier shown

Sequential Turn-On/Off (STO)
TO AMPLIFIER
POWER SUPPLY
MAINS
SEQUENTIAL
TURN ON
OUT
DC Power
IN
To
String
BLOCK DIAGRAM
Crest Audio Inc.
100 Eisenhower Dr., Paramus NJ 07652 USA
TEL: [phone] FAX: [phone]
http://www.crestaudio.com
Printed in USA
CC-SDC Power/Output Module
SPECIFICATIONS
Pass-thru sequence time: 200ms
Connectors: 5mm, 4-pin Phoenix connector (STO)
Amplifier output barrier strip* with 0.44" (11mm) center and 0.32" (8mm) lug space
Controls: Signal chassis ground lift jumper
*See CKS / CKV power amplifier operator’s manual for power output specifications.
v. 2.1 4/7/97
Crest Audio reserves the right to make improvements in manufacturing or design which may affect specification. Crest Audio specification literature is available in electronic form to qualified users.
Contact Crest Audio Inc. for more information. NexSys is a registered trademark of Crest Audio Inc. ©1996 Crest Audio Inc.
*A3300017*