Select the EDID Mode
Select the EDID (Extended Display Identification Data) mode by moving the EDID switch to
either of the following positions:
• DEFAULT: (Default setting) The device sends a predefined Crestron EDID to the
input device. The Crestron EDID supports 2-channel LPCM audio and 4K60 444
non-HDR video.
• COPY 1ST: The device copies the EDID of the display connected to OUTPUT 1 and
sends the EDID to the input device.
NOTE: If the display that is connected to OUTPUT 1 is disconnected, the current
EDID is retained. Connecting a different display to OUTPUT 1 does not automatically
update the EDID at the input device. To update the EDID, move the EDID switch to the
DEFAULT position and then back to the COPY 1ST position.
EDID Selection Switch (HD-DA2-4KZ-E Shown)
Select the HDCP Version
Select the HDCP version by moving the HDCP switch to one of the following positions:
• OFF: Disables HDCP support
• 1.4: Sets the HDCP version to 1.4
• 2.2: (Default setting) Sets the HDCP version to 2.2
HDCP Selection Switch (HD-DA2-4KZ-E Shown)
Observe the LEDs
Observe the LEDs on the front panel of the device:
• PWR: Lights amber to indicate that the device is booting, and lights green to indicate
that the device is powered on
• INPUT: Lights green to indicate that an HDMI signal is detected at the HDMI input
• OUTPUT 1-2, 1-4, or 1-8: Lights green to indicate that the corresponding HDMI output is
transmitting an HDMI signal
In addition to the LEDs listed above, a SETUP LED is also provided. When the SETUP button
is pressed for 10 seconds, the SETUP LED flashes red ten times to indicate that the default
settings have been restored.
Front Panel LEDs (HD-DA2-4KZ-E Shown)
Additional Information
Scan or click the QR code for detailed product information.
HD-DA2-4KZ-E HD-DA4-4KZ-E HD-DA8-4KZ-E
Compliance and Legal
This product is Listed to applicable UL® Standards and requirements tested by
Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par
Underwriters Laboratories Inc.
As of the date of manufacture, the product has been tested and found to
comply with specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following conditions: (1) This device may not cause harmful interference and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific
information, please visit www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks
of Crestron Electronics, Inc. in the United States and/or other countries.
HDMI and the HDMI logo are either trademarks or registered trademarks
of HDMI Licensing LLC in the United States and/or other countries. UL and
the UL logo are either trademarks or registered trademarks of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names
of others. Crestron is not responsible for errors in typography or photography.
©2018 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 8276B
(2053086)
11.18
Specifications subject to
change without notice.
