Crestron CLF-DIMRFB User manual

Crestron CLF-DIMRFB
infiNET™ Lamp Dimmer
Operations Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2006 Crestron Electronics, Inc.

Crestron CLF-DIMRF infiNET™Lamp Dimmer
Contents
InfiNET™Lamp Dimmer: CLF-DIMRFB 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Specifications ..............................................................................................................1
Physical Description....................................................................................................3
Industry Compliance ...................................................................................................5
Setup ..........................................................................................................................................6
Identity Code ...............................................................................................................6
Hardware Hookup ....................................................................................................... 6
Programming Software..............................................................................................................8
Earliest Version Software Requirements for the PC ...................................................8
Programming with Crestron D3 Pro or SystemBuilder ...............................................9
Programming with SIMPL Windows ..........................................................................9
Example Program ......................................................................................................11
Uploading and Upgrading........................................................................................................ 12
Establishing Communication.....................................................................................12
Programs and Firmware ............................................................................................ 13
Operation .................................................................................................................................14
Mode Selection Switch..............................................................................................14
Special Functions ......................................................................................................16
Problem Solving ......................................................................................................................19
Troubleshooting......................................................................................................... 19
Bootloader .................................................................................................................21
Reference Documents................................................................................................ 21
Further Inquiries ........................................................................................................ 22
Future Updates .......................................................................................................... 22
Return and Warranty Policies ..................................................................................................23
Merchandise Returns / Repair Service ...................................................................... 23
CRESTRON Limited Warranty.................................................................................23
Operations Guide – DOC. 6479 Contents •i

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
InfiNET™Lamp Dimmer:
CLF-DIMRFB
Introduction
Features and Functions
• Free-standing dimmer module designed to sit on the floor
• Provides dimming control of a conventional floor lamp or table
lamp
• Enables local dimming control via a built-in foot switch
• Crestron System Integration via infiNET™ Wireless Network
Specifications
Specifications for the CLF-DIMRFB are listed in the following table.
CLF-DIMRFB Specifications
SPECIFICATION DETAILS
Load Ratings
Incandescent /
Tungsten Halogen /
Magnetic Low-Voltage
500 Watts/VA
Power Requirements 120 Volts AC, 60Hz
Default MNET ID 011
(Continued on following page)
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •1

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
CLF-DIMRFB Specifications (Continued)
SPECIFICATION DETAILS
Minimum 2-Series Control
System Update File
Version 3.137 or later
Wireless2
RF Transceiver
RF Output Power
Range (typical)
2-way RF, 2.4 GHz
ISM Channels 11-26
(2400 to 2483.6 MHz),
IEEE 802.15.4 compliant
10mW
150 feet indoor, 250 feet
outdoor, subject to site-specific
conditions; range is increased by
adding additional devices
Environmental
Temperature
Humidity
32° to 104°F (0° to 40°C)
10% to 90% RH (non-
condensing)
Enclosure Free-standing, black metal with
high-impact injection-molded
plastic footswitch
Dimensions
Height
Width
Depth
2.37 in (6.02 cm)
3.15 in (8.00 cm)
3.51 in (8.92 cm)
Weight 14.46 oz (410 g)
Available Accessories
C2N-MNETGW infiNET Gateway/Transceiver
1. Requires set up with Crestron Toolbox™.
2. C2N-MNETGW gateway/transceiver required.
2 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
Physical Description
This section provides information on the connections, controls, and
indicators available on your CLF-DIMRFB.
CLF-DIMRFB Physical View
CLF-DIMRFB Overall Dimensions (Front view)
0.54 in
(1.36 cm)
2.28 in
(5.80 cm) 2.37 in
(6.02 cm)
(8.00 cm)
1
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •3

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
CLF-DIMRFB Overall Dimensions (Top view)
3.51 in
(8.92 cm)
4' LONG, AC-PLUG, 3 CONDUCTOR
5
4
3
2
Connectors, Controls, & Indicators
# CONNECTORS,
CONTROLS, &
INDICATORS
DESCRIPTION
1 AC Receptacle
(ungrounded)
Plug table/floor lamp in here
2 Foot Switch Operates dimmer*
3 LED Indicator Provides feedback*
4 Mode Selection Switch Three-position switch sets
mode of operation*
5 AC Plug Connects to 120V AC power
source
* Refer to “Operation” on page 14.
4 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
Industry Compliance
As of the date of manufacture, the CLF-DIMRFB has been tested and
found to comply with specifications for CE marking and standards per
EMC and Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •5

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
Setup
Identity Code
The MNET ID of the CLF-DIMRFB has been factory set to 01. After an
infiNET device is added to an infiNET network, its MNET ID must be
changed to a value that can be addressed by the control system program
(03 to 20). The MNET IDs of multiple CLF-DIMRFB devices in the
same system must be unique. MNET IDs are changed from a personal
computer (PC) via the Crestron Toolbox. When setting the MNET ID,
consider the following:
• The MNET ID of each unit must match an ID code specified in the
SIMPL Windows or D3 Pro™/SystemBuilder™program.
• Each network device must have a unique MNET ID.
For more details, refer to the Crestron Toolbox help file.
Hardware Hookup
Make the necessary connections as called out in the illustration that
follows this paragraph. Apply power after all connections have been
made.
When making connections to the CLF-DIMRFB, consider the following:
• The included cable cannot be extended.
• Do not use an extension cord.
6 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
Hardware Connections for the CLF-DIMRFB
TO ANY 120V AC,
60Hz POWER
SOURCE
TO LAMP
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •7

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
Programming Software
Have a question or comment about Crestron software?
Answers to frequently asked questions (FAQs) can be viewed in the
Online Help section of the Crestron website. To post a question or view
questions you have submitted to Crestron’s True Blue Support, log in at
http://support.crestron.com. First-time users will need to establish a user
account.
Earliest Version Software Requirements for the
PC
NOTE: Crestron recommends that you use the latest software to take
advantage of the most recently released features. The latest software is
available from the Crestron website.
Crestron has developed an assortment of Windows-based software tools
to develop an infiNET system. The following are the minimum
recommended software versions for the PC:
Software
TASK REQUIRED SOFTWARE
VERSION
Program control system
to operate CLF-DIMRFB.
SIMPL Windows version 2.06.20
or later with SIMPL+Cross
Compiler version 1.1 or later and
Library update 382 or later; Also
requires Crestron Database
version 18.1.0 or later.
Upload program and
firmware.
Crestron Toolbox 1.02.25 or later.
(Continued on following page)
8 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
Software (Continued)
TASK REQUIRED SOFTWARE
VERSION
Program with simple
wizards for lighting
systems using a
CLF-DIMRFB (optional
but recommended).
Crestron D3 Pro version 2.0.6 or
later or SystemBuilder version
2.0.6 or later. Refer to software
release notes or Crestron website
for other required Crestron
software packages.
Programming with Crestron D3 Pro or
SystemBuilder
Crestron D3 Pro and SystemBuilder are the easiest methods of
programming, but do not offer as much flexibility as SIMPL Windows.
For additional details, download D3 Pro or SystemBuilder from the
Crestron website and examine the extensive help files.
Programming with SIMPL Windows
NOTE: While SIMPL Windows can be used to program the
CLF-DIMRFB, it is recommended to use D3 Pro or SystemBuilder for
configuring system.
SIMPL Windows is Crestron’s premier software for programming
Crestron control systems. It is organized into two separate, but equally
important “Managers”.
Configuration
Manager Configuration Manager is the view where programmers “build” a
Crestron control system by selecting hardware from the Device Library.
• To incorporate the CLF-DIMRFB into the system, first drag the
C2N-MNETGW (MNET Gateway) from the Wireless Receivers |
Wireless Receivers (RF) folder of the Device Library and drop it in
the System Views. Then drag the CLF-DIMRFB from the Lighting
| Wall Dimmers/Switches (infiNET CLW Series) folder of the
Device Library and drop it on the C2N-MNETGW.
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •9

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
Locating the C2N-MNETGW in the Device Library
Locating the CLF-DIMRFB in the Device Library
• The system tree of the control system displays the device in the
appropriate slot with a default MNET ID as shown in the following
illustrations.
C2Net Device, Slot 9
• Additional CLF-DIMRFB devices are assigned different MNET
ID numbers as they are added.
• If necessary, double click a device to open the “Device Settings”
window and change the MNET ID, as shown in the following
figure.
10 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
“CLF-DIMRFB Device Settings” Window
• The ID code specified in the SIMPL Windows program must
match the MNET ID of each unit.
Programming
Manager Programming Manager is the view where programmers "program" a
Crestron control system by assigning signals to symbols. The symbol can
be viewed by double clicking on the icon or dragging it into Detail View.
A description for each signal in the symbol is described in the SIMPL
Windows help file (F1).
Example Program
An example program for the CLF-DIMRFB is available from the
Crestron website (http://www.crestron.com/exampleprograms).
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •11

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
Uploading and Upgrading
Crestron recommends using the latest programming software and that
each device contains the latest firmware to take advantage of the most
recently released features. However, before attempting to upload or
upgrade, it is necessary to establish communication.
Establishing Communication
Use Crestron Toolbox for communicating with the CLF-DIMRFB; refer
to the Crestron Toolbox help file for details. There is a single method of
communication: indirect serial communication.
Indirect Serial Communication
PC RUNNING
CRESTRON TOOLBOX
CONTROL SYSTEM
CLF-DIMRFB
SERIAL,
ETHERNET
OR USB
infiNETC2N-MNETGW
CRESNET
• CLF-DIMRFB connects to C2N-MNETGW (Gateway), which
connects to control system via Cresnet.
• Establish communications between the PC and the control system
as described in the latest version of the 2-Series Reference Guide
(Doc. 6256), which is available from the Crestron website
(http://www.crestron.com/manuals).
12 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
Programs and Firmware
• Display the network device tree (Tools | Network Device Tree) to
show all network devices connected to the control system. Right-
click on the CLF-DIMRFB to display actions that can be
performed on the CLF-DIMRFB:
Upgrade firmware⇒
⇒
⇒
⇒
Change MNET ID
• Upload the SIMPL Windows file to the control system using
SIMPL Windows or Crestron Toolbox.
• Upgrade CLF-DIMRFB firmware via Crestron Toolbox.
Establish serial communications with the CLF-DIMRFB and
display the “System Info” window.
Select Functions | Firmware… to upgrade the
CLF-DIMRFB firmware.
For details on uploading and upgrading, refer to the SIMPL Windows
help file or the Crestron Toolbox help file.
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •13

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
Operation
The CLF-DIMRFB may be warm to the touch during operation. This is
normal.
Mode Selection Switch
These dimmers use a three-position mode selection switch to set the
mode of operation.
OFF
When the mode selection switch is in the “OFF” position, the foot switch
will not have any function and the load is disconnected from the power
source. This must be used when changing light bulbs to ensure that the
load is fully disconnected from power.
RUN
When the mode selection switch is in the “RUN” position, it is operating
in the RUN mode. This is the normal operating mode of the dimmer. The
RUN mode is used to recall the preset light level. Refer to the following
table for a list of available functions when the dimmer is operating in the
RUN mode.
NOTE: To enter RUN mode, move mode selection switch to the “RUN”
position, without pausing at the “SET” position.
RUN Mode Functions
EVENT ACTION
RUN mode entered
(from OFF mode).
Recall last load state.
RUN mode entered
(from SET mode).
Store the current load level to the
preset level. (Refer to “SET Mode
Functions” on next page.) Cannot save
0%. Any level less than 10% will store
as 10%.
(Continued on following page)
14 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479

Crestron CLF-DIMRFB infiNET™Lamp Dimmer
RUN Mode Functions (Continued)
EVENT ACTION
Foot switch is
pressed.
Toggle between the preset level and
OFF, using the following rule:
If load is currently OFF, recall preset,
otherwise turn load OFF.
SET
When the mode selection switch is in the “SET” position, it is operating
in the SET mode. The LED will blink to indicate that the dimmer is in the
SET mode. Refer to the following table for a list of available functions
when the dimmer is operating in the SET mode.
NOTE: Mode selection switch must be in the “SET” position for at least
0.5s for unit to enter SET mode.
SET Mode Functions
EVENT ACTION
SET mode entered
(from OFF or RUN
mode).
Set the load to the preset level using a
0s fade* (or the minimum allowed
fade).
LED will blink at a steady rate while in
this mode (refer to “LED Behavior” on
page 17.
Foot switch is
pressed.
Manually raise or lower the load using
the current “ramp time”* parameter.
The behavior will be alternating;
releasing the button and pressing it
again will cause the lights to ramp in
the opposite direction. Switch to “RUN”
mode to store preset.
(User can abort any changes made in
SET mode by switching unit OFF
before returning to RUN.)
* Fade time and ramp time are parameters that can be changed in SIMPL
Windows. Refer to the SIMPL Windows help file (F1) for details.
Operations Guide – DOC. 6479 infiNET™Lamp Dimmer: CLF-DIMRFB •15

InfiNET™Lamp Dimmer Crestron CLF-DIMRFB
Special Functions
Enter ACQUIRE Mode
Before an infiNET device can be used on an infiNET network, it must
first be acquired by a C2N-MNETGW gateway that is connected to a
Cresnet network.
NOTE: A dimmer can be acquired by only one gateway.
To acquire a CLF-DIMRFB by a C2N-MNETGW, perform the
following:
1. Put the C2N-MNETGW in the ACQUIRE mode, from the unit
itself or from Toolbox, as described in the latest revision of the
C2N-MNETGW guide (Doc. 6317) which is available from the
Crestron website.
NOTE: In environments where multiple gateways are installed, only
one gateway should be in ACQUIRE mode at a time.
2. Place the CLF-DIMRFB in the ACQUIRE mode by doing the
following:
a. Move the mode selection switch to the “OFF” position.
b. Press and hold the foot switch, while sliding the mode
switch to the “RUN” position.
c. Continue holding the foot switch until you see the LED
blink once. Now release the foot switch; the unit is now in
ACQUIRE mode.
NOTE: ACQUIRE mode does not actually start until the foot
switch is released.
After approximately 10 seconds, the LED will start to blink slowly
and the dimmer will attempt to acquire with a C2N-MNETGW that
is in the ACQUIRE mode. The device is acquired then the LED
stops blinking. Acquiring can take up to five minutes to complete.
After being acquired, the device will exit the ACQUIRE mode.
3. Take the C2N-MNETGW out of the ACQUIRE mode once all
devices have been acquired. Refer to the latest revision of the
C2N-MNETGW guide (Doc. 6317).
16 •infiNET™Lamp Dimmer: CLF-DIMRFB Operations Guide – DOC. 6479