Crestron Green Light DIN-1DIM4 How to use

Crestron Green Light®
DIN-1DIM4
DINRail4-ChannelDimmer
Operations & Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Operation is subject to the following two conditions:
Industry Canada (IC) Compliance Statement
1. This device may not cause interferecne, and
2. This device must accept any interference, including interference that may cause undesired operation of the
device.
As of the date of manufacture, the DIN-1DIM4 has been tested and found to comply with specifications for CE
marking and standards per EMC and Radiocommunications Compliance Labelling.
(E103692)
All brand names, product names and trademarks are the property of their respective owners.
©2009 Crestron Electronics, Inc.

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
Contents
Crestron Green Light® DIN Rail Four Channel Dimmer: DIN-1DIM4 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Applications.................................................................................................................3
Specifications ..............................................................................................................4
Physical Description....................................................................................................6
Setup........................................................................................................................................11
Network Wiring.........................................................................................................11
Identity Code.............................................................................................................11
Installation.................................................................................................................12
Hardware Hookup .....................................................................................................14
Programming Software............................................................................................................16
Earliest Version Software Requirements for the PC .................................................16
Programming with Crestron SystemBuilder..............................................................16
Programming with D3 Pro.........................................................................................16
Programming with SIMPL Windows........................................................................17
Example Program......................................................................................................19
Uploading and Upgrading........................................................................................................20
Establishing Communication.....................................................................................20
Programs and Firmware ............................................................................................21
Program Checks ........................................................................................................21
Operation.................................................................................................................................22
Problem Solving ......................................................................................................................25
Troubleshooting.........................................................................................................25
Check Network Wiring..............................................................................................27
Reference Documents................................................................................................29
Further Inquiries........................................................................................................29
Future Updates ..........................................................................................................29
Return and Warranty Policies..................................................................................................30
Merchandise Returns / Repair Service ......................................................................30
CRESTRON Limited Warranty.................................................................................30
Operations & Installation Guide – DOC. 6928A Contents •i

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
Crestron Green Light®
DIN Rail Four Channel Dimmer:
DIN-1DIM4
Introduction
The DIN-1DIM4 is a DIN rail mounted lighting control module with four
channels of dimming. A single model supports both 120 and 220-277
Volt electronic and magnetic low-voltage, incandescent, neon/cold
cathode, 2-wire dimmable fluorescent, and non-dimmable lighting loads
up to 5 Amps per channel, 10 Amps total.
Features and Functions
• Four channels of dimming
• 120 to 277 Volt 50/60 Hz operation
• Selectable non-dim mode
• Master air-gap relay
• Override input
• Cresnet®communications
• Setup via front panel or software
• Programmable functionality via DIN-AP2
• 12M wide DIN rail mounting
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •1

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Phase-Synchronous Detection Circuitry
Crestron®proprietary zero cross filter technology provides superior
immunity to noise on the power line, reducing lamp flicker and
compensating for fluctuations in line voltage and frequency.
Master Air-Gap Relay
When all four channels are turned fully off, the internal master relay
automatically opens providing air-gap isolation to allow safe servicing
and changing of light bulbs on all four controlled circuits.
Override Input
An override input is provided to allow an external contact closure to
momentarily override the control system program and set each channel
output to its override preset level. Levels can be adjusted and saved
locally from the front panel, or remotely via software.
DIN Rail Installation
The DIN-1DIM4 is designed to snap onto a standard DIN rail for
installation in a wall mount enclosure. Wiring connections are made
using screw terminals positioned along the bottom, clearly accessible
from the front for easy installation and servicing. All setup controls and
indicators are positioned on the center front panel. When installed in an
enclosure utilizing 45 mm cutouts, the DIN-1DIM4’s front panel stays
accessible while the connections are concealed.
Cresnet®
The DIN-1DIM4 communicates with a DIN-AP2 2-Series Automation
Processor, or other Crestron 2-Series control system, via the Cresnet
control network. A pair of Cresnet ports is provided on the DIN-1DIM4
allowing for easy daisy-chaining of several DIN Rail Series automation
control modules.
2 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
Applications
The following diagram shows a DIN-1DIM4 in a typical application.
DIN-1DIM4 in a Typical Application
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •3

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Specifications
Specifications for the DIN-1DIM4 are listed in the following table.
DIN-1DIM4 Specifications
SPECIFICATION DETAILS
Load Ratings
Dimmer Channels 4
Maximum Per Channel 5 Amps @ 120-240 Volts AC,
50/60 Hz;
600 Watts @ 120 Volts AC;
1150 Watts @ 230 Volts AC;
1200 Watts @ 240 Volts AC;
1385 Watts @ 277 Volts AC
Module Total 10 Amps @ 120-240 Volts AC,
50/60 Hz;
1200 Watts @ 120 Volts AC;
2300 Watts @ 230 Volts AC;
2400 Watts @ 240 Volts AC;
2770 Watts @ 277 Volts AC
Load Types Leading edge (forward phase)
electronic low voltage,
incandescent, neon/cold cathode,
magnetic low voltage, dimmable
2-wire fluorescent, and non-dim
lighting
Input Voltage
Line Power 120-277 Volts AC, 50/60 Hz
Power Requirements
Cresnet Power Usage 0.6 Watts
(0.03 Amps @ 24 Volts DC) when
line power is not available
Default Net ID 98
Minimum 2-Series Control
System Update File1, 2 Version 4.000.0226 or later
(Continued on following page)
4 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
DIN-1DIM4 Specifications (Continued)
SPECIFICATION DETAILS
Environmental
Temperature 0º to 40º C (32º to 104º F)
Humidity 10% to 90% RH
(non-condensing)
Heat Dissipation 52 BTU/Hr @ 120 Volts with two
channels
Enclosure Aluminum with polycarbonate
label overlay, 35 mm DIN EN
60715 rail mount, DIN 43880 form
factor for enclosures with 45 mm
front panel cutout, occupies 12
DIN module spaces (216 mm)3
Dimensions
Height 95 mm (3.71 in)
Width 216 mm (8.49 in)
Depth 60 mm (2.35 in)
Weight 912 g (34 oz)
1. The latest software versions can be obtained from the Crestron website. Refer to
the NOTE following these footnotes.
2. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest
Crestron Product Catalog for a complete list of 2-Series control systems.
3. Unit dissipates significant heat when fully loaded and should be mounted in an
enclosure that is sufficiently ventilated to maintain an ambient temperature not
exceeding 40º C (104º F). Maintain 100 mm (4 inches) minimum spacing above
and below for proper ventilation and heat dissipation, 150 mm (6 inches) spacing
recommended.
NOTE: Crestron software and any files on the website are for authorized
Crestron dealers and Crestron Authorized Independent Programmers
(CAIP) only. New users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •5

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Physical Description
This section provides information on the connections, controls and
indicators available on your DIN-1DIM4.
DIN-1DIM4 Physical View
6 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
DIN-1DIM4 Overall Dimensions (Front View)
216 mm
(8.49 in)
90 mm
(3.54 in)
95 mm
(3.71 in)
1 2 3 4 5 6
7
11 12 13 14 15 16
8
9
10
DIN-1DIM4 Overall Dimensions (Side View)
58 mm
(2.28 in)
60 mm
(2.35 in)
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •7

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Connectors, Controls & Indicators
# CONNECTORS1,
CONTROLS &
INDICATORS
DESCRIPTION
1 NET ID
DISPLAY and
CONTROL
(2) 7-segment green LED digits
and (2) miniature pushbuttons
for setting Cresnet ID; digits
also display output levels and
protection/error codes
2 SETUP
(LED and BUTTON) (1) Red LED and (1) recessed miniature pushbutton for
enabling setup mode and
touch-settable ID
3 OVR
(LED and BUTTON) (1) Red LED and (1) miniature pushbutton for enabling
Override mode and saving
override presets;
Maximum wire size: 1.5mm2
(16 AWG);
For more information, refer to
“Operation” which starts on
page 22.
4 PWR LED (1) Green LED, normally
indicates AC line power is
connected to either LIVE
terminal, blinks when only
powered by Cresnet
5 NET LED (1) Yellow LED, indicates
communication with the control
processor
6 RESET (1) Recessed miniature
pushbutton, resets internal
processor
(Continued on following page)
8 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
Connectors, Controls & Indicators (Continued)
# CONNECTORS1,
CONTROLS &
INDICATORS
DESCRIPTION
7 DIM (1 – 4) LED (4) Red LEDs, illuminate when
a corresponding channel is
operating in forward-phase
mode
8 NON-DIM (1 – 4) LED (4) Red LEDs, illuminate when
a corresponding channel is
operating in non-dim mode
9 CHANNEL MODE
SELECT
(1 – 4)
(4) Recessed miniature
pushbuttons, used to select
each channel’s operating
mode;
For more information, refer to
“Operation” which starts on
page 22.
10 LOADS (1 – 4)
(LEDs and BUTTONS)
(4) Red LEDs and (4) miniature
pushbuttons for status
indication and local control of
each channel
11 NET
(2) 4-pin 3.5 mm detachable
terminal blocks, paralleled;
Cresnet slave port
Maximum wire size: 1.5 mm2
(16 AWG)
24: Power (24 Volts DC)
Y: Data
Z: Data
G: Ground
(Continued on following page)
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •9

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Connectors, Controls & Indicators (Continued)
# CONNECTORS1,
CONTROLS &
INDICATORS
DESCRIPTION
12 OVERRIDE
(2) 2-pin 3.5mm detachable
terminal blocks, paralleled;
Sensing input for external
low-voltage contact closure;
Activates Override mode when
a closure is present;
Minimum Closure Rating:
10mA (per module) at 24 Volts
13 LIVE (2) Captive screw terminals2,
brown;
Line power input
14 NEUTRAL
(5) Captive screw terminals2,
blue
15 DIMMED LIVE (1 – 4) (4) Captive screw terminals2,
red;
Dimmer channel outputs 1 – 4
16 GROUND
(5) Captive screw terminals2,
green
1. Interface connectors for NET and OVERRIDE ports are provided with the unit.
2. Captive screw terminals accept up to 2.5 mm2(12 AWG) wires per terminal.
10 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
Setup
Network Wiring
When wiring the Cresnet®network, consider the following:
• Use Crestron Certified Wire.
NOTE: Cresnet HP cannot be used.
• Use Crestron power supplies for Crestron equipment.
• Provide sufficient power to the system.
CAUTION: Insufficient power can lead to unpredictable results
or damage to the equipment. Please use the Crestron Power
Calculator to help calculate how much power is needed for the
system (www.crestron.com/calculators).
• For networks with 20 or more devices, use a Cresnet Hub/Repeater
(DIN-HUB) to maintain signal quality.
For more details, refer to “Check Network Wiring” which starts on page
27.
Identity Code
The Net ID of the DIN-1DIM4 has been factory set to 98. The Net IDs of
multiple DIN-1DIM4 devices in the same system must be unique. Net
IDs are changed on the front panel of the DIN-1DIM4 or from a personal
computer (PC) via Crestron Toolbox™ (refer to “Establishing
Communication” on page 20).
To set the Net ID using the front panel:
1. Press the SETUP button to enter the Setup mode. The SETUP
LED illuminates.
2. Press the left button under the NET ID display to change the most
significant digit of the Net ID or press the right button under the
NET ID display to change the least significant digit of the Net ID
number.
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •11

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
3. When the desired Net ID is displayed, press the SETUP button to
exit the Setup mode. The SETUP LED extinguishes.
NOTE: If an invalid Net ID is set (e.g., 00, 02, FF), “Er” will be
displayed on the NET ID display. The DIN-1DIM4 will revert to
the previously set Net ID.
NOTE: The DIN-1DIM4 will leave the Setup mode after 10
seconds of inactivity. The DIN-1DIM4 will revert to the previously
set Net ID.
NOTE: Regardless of the method used to set the NET ID, a small
label (with numbers and letters) is provided on the front panel of
the DIN-1DIM4 to document the unit’s Net ID in the case where
power is not available. Apply a mark over the digits that
correspond to the assigned Net ID.
NET ID Label (“3C” Shown)
When setting the Net ID, consider the following:
• The Net ID of each unit must match an ID code specified in the
SIMPL™ Windows program.
• Each network device must have a unique Net ID.
For more details, refer to the Crestron Toolbox help file.
Installation
The DIN-1DIM4 must be installed by a licensed electrician, in
accordance with all national and local codes.
CAUTION: This equipment is for indoor use only. Mount in a well
ventilated area. The ambient temperature must be 0º to 40º C
(32º to 104º F). The relative humidity must be 10% – 90%
(non-condensing).
NOTE: When installing in an enclosure, high-voltage devices should be
grouped separately from low-voltage devices.
12 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
The DIN-1DIM4 is designed for installation on a DIN rail. Refer to the
following diagram when installing.
Installing the DIN-1DIM4
DIN Rail
Release
Top
DIN Rail
(Not Supplied)
DIN-1DIM4
1. Use a flat object (e.g., a flat-head screwdriver) to pull the DIN rail
release downward.
2. With the top of the unit tilted toward you, place the DIN-1DIM4
against the bottom of the DIN rail.
NOTE: When mounting DIN rail products, it may be necessary to
use a flat-head screwdriver to pull the DIN rail release tab while
snapping the device onto the DIN rail.
3. Tilt the top of the DIN-1DIM4 toward the DIN rail until it is
secure on the top edge of the rail. Push the DIN rail release upward
to lock the DIN-1DIM4 into place.
To remove the DIN-1DIM4 from the DIN rail, use a small, flat object
(e.g., a flat-head screwdriver) to pull the DIN rail release downward to
unlock it and tilt the top of the DIN-1DIM4 away from the DIN rail.
NOTE: Certain third party DIN cabinets provide space for an
informational label between each DIN rail row. Crestron’s Engraver
software (version 4.0 or later) can generate appropriate labels for all
Crestron DIN rail products.
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •13

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Hardware Hookup
Make the necessary connections as called out in the illustration that
follows this paragraph. Refer to “Network Wiring” on page 11 before
attaching the 4-position terminal block connector. Apply power after all
connections have been made.
WARNING: Prior to connecting the device, turn off power at the circuit
breaker. Failure to do so may result in serious personal injury or damage
to the device. Restore power after all connections have been made.
CAUTION: Connecting this device to the wrong type of load or
short-circuiting the load can cause severe product damage. Each load
should be tested to identify a short circuit condition prior to wiring the
load to the module.
NOTE: Install in accordance with all local and national electric codes.
NOTE: High-voltage connections accept 2.5 mm2(12 AWG) wire. Wire
should be stripped to 8 mm (1/3 inch). Tighten terminal blocks to 0.5 Nm
(5 in-lbs).
NOTE: Use copper wire only. For high-voltage connections, use wire
rated for at least 75º C (167º F).
NOTE: The DIN-1DIM4 power feed must be protected by a 10 A (trip
curve C) breaker or equivalent.
NOTE: The DIN-1DIM4 outputs must be used for control of
permanently installed lighting loads only.
NOTE: Do not mix magnetic and electronic transformers on the same
dimmer output.
NOTE: Ensure the unit is properly grounded by connecting the chassis
ground lug to an earth ground (building steel).
NOTE: To prevent overheating, do not operate this product in an area
that exceeds the environmental temperature range listed in the table of
specifications.
14 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A

Crestron DIN-1DIM4 DIN Rail 4-Channel Dimmer
When making connections to the DIN-1DIM4, use Crestron power
supplies for Crestron equipment.
Hardware Connections for the DIN-1DIM4
LIVE:
Line Power Input
from AC Power
Line
OVERRIDE:
From Device Providing Override
Signal and to Other Devices
Receiving Override Signal
NET:
To Control System
and Other Cresnet
Devices
NEUTRAL:
Neutral Connection
from AC Power
Line
Ground
DIMMED LIVE (1 – 4):
Dimmer Channel
Outputs
With the circuit breaker turned off, connect the wires to the terminal
blocks per the markings provided on the DIN-1DIM4.
Load Connections Example for the DIN-1DIM4
Neutral
Line Ground
Neutral
Line
Ground
120/277 Volts
Load
120/277 Volts
From Breaker
Operations & Installation Guide – DOC. 6928A DIN Rail 4-Channel Dimmer: DIN-1DIM4 •15

DIN Rail 4-Channel Dimmer Crestron DIN-1DIM4
Programming Software
Have a question or comment about Crestron software?
Answers to frequently asked questions (FAQs) can be viewed in the
Online Help section of the Crestron website. To post a question or view
questions you have submitted to Crestron’s True Blue Support, log in at
www.crestron.com/support. First-time users will need to establish a user
account.
Earliest Version Software Requirements for the
PC
NOTE: Crestron recommends that you use the latest software to take
advantage of the most recently released features. The latest software is
available from the Crestron website.
Crestron has developed an assortment of Windows®-based software tools
to develop a Cresnet system. You can create a program to control the
DIN-1DIM4 control system using the Crestron programming tools
Crestron SystemBuilder™, D3 Pro®or SIMPL Windows. Customers
whose focus is on lighting systems may prefer to use the D3 Pro software
since it is designed especially for creating lighting and environmental
system control applications. Customers already familiar with SIMPL
Windows who are including a lighting system as part of an overall
control system project may prefer to continue using SIMPL Windows.
For the minimum recommended software versions, visit the Version
Tracker page of the Crestron website (www.crestron.com/versiontracker).
Programming with Crestron SystemBuilder
Crestron SystemBuilder™ is the easiest method of programming but does
not offer as much flexibility as SIMPL Windows. For additional details,
download SystemBuilder from the Crestron website and examine the
extensive help file.
Programming with D3 Pro
Crestron’s D3 Pro®lighting software provides all the tools necessary to
create a complete Crestron lighting system for residential applications.
16 •DIN Rail 4-Channel Dimmer: DIN-1DIM4 Operations & Installation Guide – DOC. 6928A