Crestron DM-NVX-E20 User manual

The Crestron DM-NVX-E20 is a network AV encoder that transmits up
to 4K60 4:2:0 video over standard Gigabit Ethernet to a DM NVX®
decoder. The DM-NVX-D20 is a network AV decoder that receives up to
4K60 4:2:0 video from a DM NVX encoder.
The DM-NVX-E20 provides a single HDMI® input, and the DM-NVX-D20
provides a single HDMI output. Both devices feature secure web-based
control and management, an analog audio output, and copper LAN
connectivity with PoE (Power over Ethernet) support.
In the Box
1 DM-NVX-E20 or DM-NVX-D20
Additional Items
2 Connector, 3-Pin (2003575)
1 Connector, 2-Pin (2003574)
Install the Device
The DM-NVX-E20 and DM-NVX-D20 can be mounted onto a flat
surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a flat
surface such as a wall or the underside of a table. The screw diameter
should be no more than 6 mm. Be sure to use the mounting hardware
that is appropriate for the surface to which the device is being mounted.
NOTE: Fan ventilation holes are provided on five sides of the device.
Ifthe installation necessitates that another object be positioned flush
against the ventilation holes on one side of the device, leave a
minimum clearance of 2 inches of space on all other sides containing
ventilation holes.
Wall Mounting (DM-NVX-E20 Shown)
DM-NVX-E20 and DM-NVX-D20 QuickStart
DM NVX® 4K60 4:2:0 Network AV Encoder and Decoder
1

Mounting onto a Rack Rail
Using two rack mounting screws (not included), mount the left or right
mounting flange of the device onto the front or rear rail of a rack.
Rack Rail Mounting Example (DM-NVX-E20 Shown)
Connect the Device
Connect the device as required for the application.
NOTES:
lThe Ethernet port must be connected to a 1000BASE-T Ethernet
switch in order to stream network video.
lThe DM-NVX-E20 and DM-NVX-D20 can be powered via the
Ethernet port, which is a PoE powered device (PD) port. In order for
the device to receive PoE, the Ethernet port must be connected to a
PoE power sourcing equipment (PSE) port of an Ethernet switch.
Wiring that connects to a PoE PSE port is designed for intrabuilding
use only.
Alternatively, the DM-NVX-E20 and DM-NVX-D20 can be powered
by a 24 VDC power pack (PW-2407WU, sold separately).
2
DM-NVX-E20 and DM-NVX-D20 QuickStart
DM NVX® 4K60 4:2:0 Network AV Encoder and Decoder

DM-NVX-E20 Front Panel Connections
DM-NVX-D20 Front Panel Connections
3
DM-NVX-E20 and DM-NVX-D20 QuickStart
DM NVX® 4K60 4:2:0 Network AV Encoder and Decoder

DM-NVX-E20 and DM-NVX-D20 Rear Panel Connections
4
DM-NVX-E20 and DM-NVX-D20 QuickStart
DM NVX® 4K60 4:2:0 Network AV Encoder and Decoder

Upgrade the Firmware
Before using the device, upgrade the firmware. The latest firmware can
be downloaded from the DM-NVX-E20 and DM-NVX-D20 product
pages on the Crestron website.
Configure the Device
Configure the device using the web interface. To access the web
interface, open a web browser and then go to the IP address of the
device.
NOTE: By default, the IP address of a DM NVX device is assigned by a
DHCP server on the network. If a DHCP server does not exist on the
network, the IP address defaults to a link-local address in the
169.254.xxx.xxx range (refer to RFC 3927 for detailed information
about link-local addressing). To find the IP address of the DM NVX
device, use the Device Discovery tool in the Crestron Toolbox™
software.
If no account has been created, create an account by entering a user
name and password and confirming the password. After an account is
created, sign in to the web interface by entering the user name and
password.
Connect to the Cloud
The XiOCloud®service allows supported devices across an enterprise to
be managed and configured from one central and secure location in the
cloud. Supported Crestron® devices are configured to connect to the
service out of the box.
Use of the service requires a registered XiOCloud account. To register
for an XiOCloud account, refer to
www.crestron.com/Support/Tools/Licensing-Registration/XiO-Cloud-
Registration-Room-Licenses.
1. Record the MAC address and serial number that are labeled on the
shipping box or the device. The MAC address and serial number are
required in order to add the device to the XiOCloud service.
NOTE:If the device has multiple MAC addresses, use the MAC
address that is providing the primary connection back to the
network. For most devices, the Ethernet MAC address should be
used. However, if your device is connecting to the network over a
different protocol (such as Wi-Fi® communications), use the
MAC address for that protocol instead.
2. Log in to your XiOCloud account at portal.crestron.io.
3. Claim the device to the XiOCloud service as described in the
XiOCloudUserGuide.
Select the device from the cloud interface to view its status and
settings. The device may now also be managed and assigned to a group
or room. For more information, refer to the XiOCloudUserGuide.
NOTE:For XiOCloud accounts with room-based licenses, the device
must be added to a licensed room before its status and settings can be
viewed.
5
DM-NVX-E20 and DM-NVX-D20 QuickStart
DM NVX® 4K60 4:2:0 Network AV Encoder and Decoder