Crestron DMF-CI-8 User manual

The Crestron® DMF-CI-8 provides a rack-mounted solution for extending
multiple 4K video signals over Gigabit Ethernet and fiber-optic cables.
In the Box
1 DMF-CI-8, DigitalMedia™ Chassis for DM NVX™ Series Cards
Additional Items
2 Bracket, Rack Ear, 2U (2045460)
4 Foot, 0.5 in. x 0.5 in. x 0.23 in., Adhesive (2002389)
1 Power Cord, 6 ft. 7 in. (2 m) (2001134)
4 Screw, 6-32 x 3/8 in., Undercut Head, Phillips (Rear Mounting)
(2007235)
Install the Device
The DMF-CI-8 can be mounted into a rack or placed onto a flat surface.
Mounting into a Rack
To mount the device into a rack:
1. Using a #1 or #2 Phillips screwdriver (not included), remove the two
front mounting screws from the left or right side of the device.
2. Align a rack ear with the front and rear mounting holes on the device.
3. Insert the two front mounting screws removed in step 1 through the
rack ear into the front mounting holes of the device.
4. Secure the rack ear by inserting two included 6-32 x 3/8 in. rear
mounting screws through the rack ear into the rear screw holes of the
device.
5. Repeat steps 1-4 to attach the remaining rack ear to the other side of
the device.
6. Mount the device into the rack using four mounting screws
(notincluded).
Mounting into a Rack
Placing onto a Flat Surface
When placing the device onto a flat surface or stacking it with other
equipment, attach the four included feet near the corners on the
underside of the device.
DMF-CI-8 Quick Start
1

Install and Connect the Cards
The DMF-CI-8 provides eight card slots that can be used to
accommodate DM NVX™ Series cards.
CAUTION: To prevent damage to a card that is connected to cables,
disconnect all cables from the card before installing the card into a
card slot or removing the card from a card slot.
NOTES:
lIn a new DMF-CI-8 installation, Crestron recommends that
cards be installed before applying power. In an existing
DMF-CI-8 installation, cards can be added or replaced without
the need to shut down the DMF-CI-8 (the cards are hot
swappable).
lWhen installing cards into a partially populated DMF-CI-8,
install the cards into slots 5-8 before using slots 1-4. Doing so
ensures better cooling and lower power consumption. In
addition, always cover empty slots using the filler plates
provided with the DMF-CI-8.
The illustration below provides a view of a fully occupied DMF-CI-8
containing eight cards.
Apply Power to the Device
To apply power to the DMF-CI-8, connect the included AC power cord to
the AC power inlet on the device and to an AC power outlet.
Configure the Cards
For configuration information, refer to the Web Interface Guide for the
corresponding DM NVX card at www.crestron.com/manuals.
Configure the Device
To configure the DMF-CI-8, use the menu on the front panel display.
For detailed information, refer to the DMF-CI-8 Supplemental Guide
(Doc. 7861) at www.crestron.com/manuals.
DMF-CI-8 Quick Start
2

Visit the Product Page
Scan the QR code to visit the product page.
www.crestron.com/model/6507968
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, DigitalMedia, and DM NVX are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in
this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc ID 7860D
(2054879)
01/17/20
DMF-CI-8 Quick Start
3