Crestron TSW-770-MSMK-ANG User manual

The TSW-770/1070-MSMK-ANG multisurface mount kit provides a
versatile mounting solution for a TSW-770,TSS-770,TSW-1070, or
TSS-1070 touch screen. Using the kit, the touch screen can be mounted
directly to glass, granite, marble, wood paneling, plaster, smooth
masonry, or virtually any other flat surface. The touch screen can also be
mounted into a wall or supported electrical boxes. When installed, the
touch screen is angled upwards at a 20° tilt.
In the Box
1 TSW-770/1070-MSMK-ANG, Multisurface Mount Kit
Additional Items
2 Screw, 6-32 x 3/8 in., Phillips (2013475)
4 Screw, 6-32 x 1/2 in., Phillips (2007240)
2 Screw, 6-32 x 3/4 in., Phillips (2033247)
4 Screw, 6-32 x 1 in., Phillips (2007251)
4 Screw, M3 x 25 mm, Phillips (2049589)
2 Screw, M3.5 x 25 mm, Phillips (2049591)
4 Washer, #6 (2007663)
TSW-770/1070-MSMK-ANG-B-S Only
1 Bracket, Angled, Black (2056875)
1 Faceplate, Front, Black (2056894)
1 Faceplate, Rear, Black (2056896)
1 Adhesive, Foam, Black (2056892)
1 Label, Polycarbonate, Black (4532843)
TSW-770/1070-MSMK-ANG-W-S Only
1 Bracket, Angled, White (2056770)
1 Faceplate, Front, White (2056893)
1 Faceplate, Rear, White (2056895)
1 Adhesive, Foam, White (2056891)
1 Label, Polycarbonate, White (4532842)
Install the MSMK
The TSW-770/1070-MSMK-ANG can be installed over an electrical box,
into drywall, or onto a flat, smooth surface. Procedures for each
installation are provided in the sections that follow.
Electrical Box Mounting
NOTE: For U.S.-style installations, use a #2 Phillips screwdriver. For
European and U.K.-style installations, use a #1 Phillips screwdriver or
equivalent.
1. Route all necessary cables through the rear of the electrical box.
2. Attach the rear faceplate to the wall:
NOTE:Ensure that the rear faceplate is oriented so that the
"TOP"machined text is facing upward prior to installation. Also
ensure that the faceplate is level after installation.
lFor U.S.-style installations, use the four provided 6-32 x 1 in.
screws to install the rear faceplate over a 1-gang (horizontally
mounted), 2-gang, or 3-gang U.S. electrical box (as shown in
the illustration on the next page).
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled
1

lFor European-style installations, use the four provided
M3x25mm screws to install the rear faceplate over a 2-gang
European electrical box.
lFor U.K.-style installations, use the two provided M3.5 x 25 mm
screws to install the rear faceplate over a 2-gang U.K. electrical
box.
NOTE:Four washers are provided to secure the faceplate to the
electrical box if the mounting holes are too large for the included
screws.
3. Press the front faceplate into the rear faceplate until it snaps into
place.
NOTE:Ensure that the front faceplate is oriented so that the
"TOP"machined text is facing upward prior to installation. Also
ensure that the faceplate is level after installation.
NOTE:If the front faceplate needs to be removed, insert the tip
of a flathead screwdriver (or similar tool)into the machined
notches on the bottom of the faceplate, and then carefully push
against the faceplate to pop it off. Refer to the following image
for the location of the notches.
2
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled

4. Attach the angled bracket to the front faceplate using the four
provided 6-32x1/2in.screws.
5. Attach the TSW-770/1070 mounting bracket (provided with the
touch screen)to the angled bracket using the two provided
6-32x3/8in. screws. Ensure the bracket is level after installation.
NOTE:If installing a TSW-770-LB or TSW-1070-LB light bar as
part of the MSMKinstallation, the light bar must be placed in
between the TSW-770/1070 mounting bracket and the
MSMKadapter bracket during this stage of the installation. The
two provided 6-32 x 3/4 in. screws must also be used in place of
the 6-32 x 3/8 in. screws. For more information on installing the
light bar, refer to the TSW-770-LBand TSW-1070-LBQuick
Start.
6. Route all cables out of the center openings in the faceplates and
brackets and connect them to the rear of the touch screen.
7. After all connections have been made, hold the touch screen over the
mounting plate and place it gently in position so that it attaches
securely to the plate.
For more information on connecting the touch screen, refer to the
TSW-570,TSW-770, and TSW-1070 Quick Start or the TSS-770 and
TSS-1070 Quick Start.
3
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled

Drywall Mounting
1. Create a cutout in the drywall where the touch screen will be installed
for routing cables.
2. Route all necessary cables through the drywall cutout.
3. Attach the angled bracket to the drywall surface using four standard
drywall anchors and 6-AB x 1 in. drywall screws (not included).
NOTE:Ensure the angled bracket is level after installation.
4. Attach the TSW-770/1070 mounting bracket (provided with the
touch screen)to the angled bracket using the two provided
6-32x3/8in. screws. Ensure the bracket is level after installation.
NOTE:If installing a TSW-770-LB or TSW-1070-LB light bar as
part of the MSMKinstallation, the light bar must be placed in
between the TSW-770/1070 mounting bracket and the
MSMKadapter bracket during this stage of the installation. The
two provided 6-32 x 3/4 in. screws must also be used in place of
the 6-32 x 3/8 in. screws. For more information on installing the
light bar, refer to the TSW-770-LBand TSW-1070-LBQuick
Start.
5. Route all cables out of the center opening in the angled bracket and
connect them to the rear of the touch screen.
6. After all connections have been made, hold the touch screen over the
mounting plate and place it gently in position so that it attaches
securely to the plate.
Surface Mounting
The following is required for this installation: a level, a roll of masking
tape, a Phillips screwdriver, and a surface cleaning product that does not
leave a film.
Use the following procedures to mount the MSMK onto a flat pane of
glass or a similar smooth surface (such as granite, marble, plaster, or
smooth stone and masonry). The included adhesive pad attaches
permanently to the surface.
Attach the Adhesive Pad
1. Clean and dry the mounting surface thoroughly.
2. Select a mounting location for the MSMK and determine whether
raceway (not included)will be entering the MSMK from the top,
bottom, left, or right cutout.
3. Using the level, tape a horizontal reference line on the glass surface
that aligns with the lower edge of the adhesive pad. Ensure the
reference line is level before proceeding.
4. Remove the protective backing from the adhesive pad.
CAUTION:The adhesive on both sides of the pad is high-strength
bond. Once the adhesive comes in contact with a surface, it
cannot be easily removed.
5. Hold the adhesive pad at a 45-degree angle to the glass surface, and
then align the lower edge of the pad with the taped reference line. Do
not allow the adhesive to come in contact with the glass surface.
4
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled

6. Once the adhesive pad is level and aligned with the taped reference
line, press the pad to the mounting surface firmly to ensure proper
adhesion and to eliminate any trapped air bubbles.
NOTE:The adhesive wet area (the total area of the adhesive
that is free of air bubbles or debris) must be 60% or greater.
Attach the Angled Bracket
1. Use pliers (or a similar tool) to break away the appropriate knockout
on the left, right, or bottom of the angled bracket for running cables
to the touch screen.
2. Remove the protective covering from the front of the adhesive pad.
3. Hold the angled bracket at a 45-degree angle to the adhesive pad,
and then align the lower edge of the bracket with the lower edge of
the pad. Do not allow the bracket to come in contact with the
adhesive.
4. Once the angled bracket is level and aligned with the adhesive pad,
press the bracket to the pad firmly to ensure proper adhesion and to
eliminate any trapped air bubbles.
NOTE:The adhesive wet area (the total area of the adhesive
that is free of air bubbles or debris) must be 60% or greater.
Attach the TSW-770/1070 Mounting Bracket
1. Remove any existing tape guides and install any raceway (not
included) to conceal cables running to the desired knockout on the
angled bracket.
NOTE:To ensure the raceway fits into the knockout, Crestron
recommends using raceway with the following
dimensions:0.45Hx0.77in. W (11 x 20 mm).
5
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled

2. Attach the TSW-770/1070 mounting bracket (provided with the
touch screen)to the angled bracket using the two provided
6-32x3/8in. screws. Ensure the bracket is level after installation.
NOTE:If installing a TSW-770-LB or TSW-1070-LB light bar as
part of the MSMKinstallation, the light bar must be placed in
between the TSW-770/1070 mounting bracket and the
MSMKadapter bracket during this stage of the installation. The
two provided 6-32 x 3/4 in. screws must also be used in place of
the 6-32 x 3/8 in. screws. For more information on installing the
light bar, refer to the TSW-770-LBand TSW-1070-LBQuick
Start.
Attach the Touch Screen
1. Route all cables through the chosen knockout and out of the center
opening in the angled bracket, and then connect them to the rear of
the touch screen.
2. After all connections have been made, hold the touch screen over the
mounting plate and place it gently in position so that it attaches
securely to the plate.
Attach the Plastic Cap (Optional)
To provide a finished appearance for installations on glass or other
transparent surfaces, install the included molded plastic cap on the
opposite side of the surface behind the MSMK.
To install the plastic cap:
1. Clean and dry the rear of the mounting surface thoroughly.
2. Using the level, tape a horizontal reference line on the glass surface
that aligns with the lower edge of the angled bracket on the opposite
side. Ensure the reference line is level before proceeding.
3. Remove the protective liner from the rear of the label.
CAUTION: The adhesive on the rear of the label is high-strength
bond. Once the adhesive comes in contact with a surface, it
cannot be removed easily.
4. Hold the label at a 45-degree angle to the adapter bracket, and then
align the lower edge of the label with the lower edge of the bracket.
Do not allow the label adhesive to come in contact with the surface.
6
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled

5. Once the label is level and aligned with the angled bracket, press the
label to the pad firmly to ensure proper adhesion and to eliminate
any trapped air bubbles.
Visit the Product Page
Scan the QR code to visit the product page.
TSW-770/1070-MSMK-ANG
www.crestron.com/model/6511786
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
©2021 Crestron Electronics, Inc.
Doc. 8960C
09/07/21
7
TSW-770/1070-MSMK-ANG QuickStart
Multisurface Mount Kit for TSW-770 and TSW-1070 Series, Angled