Crestron UC-SB1-CAM-L-FLEX User manual

The Crestron® UC-SB1-CAM-L-FLEX UC Video Conference Smart
Soundbar &Camera is a front-of-room device that eliminates the need to
install additional microphones, speakers, or cameras in a conference
space. It can be placed on a credenza beneath the room display(s) or
mounted on a wall.
In the Box
1 UC-SB1-CAM-L-FLEX, UC Video Conference Smart
Soundbar & Camera
Additional Items
4 Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (2052565)
1 Cable, USB 3.0, A - B, 6 ft (1.83 m) (2053077)
2 Foot, 2.3 in. x 0.96 in. x 0.15 in., Rubber (2052169)
1 Key, Anchor (4529654)
1 Power Cord, 5 ft 10 in. (1.78 m) (2042043)
1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (2045873)
4 Screw, 8-AB x 1-1/2 in., Pan Head, Combo (2052567)
1 Template, Overlay (4529513)
1
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

Install
The soundbar can be placed on a flat surface or mounted on a wall. The soundbar has the following dimensions.
Place on a Flat Surface
If the soundbar is to be placed on a flat surface, attach the included rubber feet to the bottom of the soundbar as shown.
2
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

Mount on a Wall
The soundbar includes anchors that are suitable for mounting it on sheetrock walls up to 1/2 in. (13 mm) thickness. Masonry and other materials may
require additional installer-supplied mounting hardware.
NOTES:
lFor optimal viewing results, the soundbar should be mounted in a location that places the camera approximately 12 in. (305 mm) above the plane of
the room’s conference table.
lWhen mounting on a wall beneath a display device, leave 3/4 in. (19 mm) (minimum) clearance above the top of the soundbar. Use the included
template to allow for sufficient clearance between the soundbar and display device.
The following tools are required to mount the soundbar:
lDrywall saw (not included)
lDrill with 5/16 in. bit (not included)
A template is included to provide drill hole locations for the included mounting hardware.
1. Attach the template to the desired mounting location with the template's center reference line at the center of the desired location.
NOTE:Use the center reference hole of the template as a guide to attach the template.
3
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

2. Drill two pilot holes on each side of the center reference line as shown in the previous diagram. Each side should have one pilot hole drilled in each row
of the template.
3. Use a drywall saw to make a cutout in the wall for the soundbar cables.
NOTE: The cutout in the center of the template provides adequate access for all of the required cabling.
4. Install the four included anchors and screws into the drilled pilot holes.
5. Place the soundbar face down, and pivot the wall bracket away from the soundbar.
4
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

6. Place the wall bracket over the screws, and hand tighten the screws until the wall bracket is secured to the wall.
7. Route the cables through the cable cutout, and connect the cables as described in Connect.
NOTE: The included power pack's cord is typically routed from the wall opening, through the cable cutout, to the soundbar.
5
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

Connect
Make the necessary connections as called out in the following diagram. Connect power last.
lPC: Connect the included USB cable to the PC port and to a USB port on the UCEngine. For optimal results, use a USB 3.0 connection.
lCAMERA: The integrated camera is already connected from the factory.
l24 V, 2.5 A: Connect the power pack to the 24 V, 2.5 A power input and to an AC power outlet.
lAUDIO IN and AUDIO OUT: The soundbar provides unbalanced, stereo, analog input and output jacks (3.5 mm TRS mini-phone). The AUDIOINport
accommodates an optional line-level audio source which feeds to the internal amplifier and speakers without a volume control or other signal
processing. The AUDIOOUT port provides a line-level signal for an optional assistive listening system and carries the same audio signal as the
soundbar speakers.
6
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

Complete
Once all connections are made, pivot the soundbar up to the wall bracket
until the soundbar locks into place.
Operation
Status
The front panel status bar illuminates to provide operational information.
lA green status bar indicates the volume level. Raising the volume
increases the status bar's illumination. Lowering the volume decreases
the status bar's illumination. When the volume = “0”, the status bar is
unlit.
lMuting the microphone and speaker turns the two outer segments of
the status bar red.
7
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

lMuting the microphone turns the center of the status bar red.
System Control
When used as part of a Crestron Flex system, the soundbar is controlled
by the system's touch screen.
For More Information
The UC-SB1-CAM-L-FLEX is an integral component of the following
Crestron Flex UC Video Conference Systems:
UC-B30-T Crestron Flex Wall Mount UC Video Conference System for
Microsoft Teams® Software
UC-B30-Z Crestron Flex Wall Mount UC Video Conference System for
Zoom Rooms™ Software
8
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera

Additional Information
Regulatory Model:UC-SB
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Microsoft Teams is
either a trademark or registered of Microsoft Corporation in the United States and/or
other countries. Zoom Rooms is either a trademark or registered trademark of Zoom
Video Communications, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to
refer to either the entities claiming the marks and names or their products. Crestron
disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 8777A
07/30/20
9
UC-SB1-CAM-L-FLEX QuickStart
UC Video Conference Smart Soundbar & Camera