Cretors 1100 User manual

MODEL 1100
10/20/2016
1
176 MITTEL DRIVE, WOOD DALE, IL 60191
Pretzel Display CaseManual
Model 1100
120 Volt
Single Phase, 60 Cycle
100/120 Volt
Single Phase, 50/60 Cycle
READ and UNDERSTAND these operating and safety
instructions before operating this machine!

MODEL 1100
10/20/2016
2
TABLE OF CONTENTS
I. SAFETY ALERT SYMBOL...................................................................................3
II. SAFETY FIRST ....................................................................................................3
III. INTRODUCTION ..................................................................................................3
IV. PURPOSE OF MANUAL......................................................................................4
V.
INSTALLATIONINSTRUCTIONS
......................................................................4
VI. OPERATING INSTRUCTIONS.............................................................................4
VII.
SANITATION INSTRUCTIONS
..........................................................................5
VIII. MAINTENANCE INSTRUCTIONS........................................................................6
IX.TROUBLESHOOTING..........................................................................................6
X. EXPLODED PARTS DIAGRAM ...........................................................................7
XI. REPLACEMENT PARTS LIST.............................................................................8
XII. WIRING DIAGRAM ..............................................................................................9

MODEL 1100
10/20/2016
3
I. SAFETY ALERT SYMBOL
II. SAFETY FIRST
The information in this manual is essential for the safe installation and
operation of your Cretors machine. The manual must be read and
understood before installing, and operating the equipment, or equivalent
training must be provided.
“The employer shall instruct each employee in the recognition and
avoidance of unsafe conditions, as well as, the regulations applicable to
his work environment and to control or eliminate any hazards or other
exposure to illness or injury”. Ref.: 29 CFR 1926.20 (b)(4)(a)(2)
It is understood that safety rules within individual companies vary. If a
conflict exists between the safety procedures contained in this manual
and the rules of a using company, the more stringent rule should take
precedence.
III. INTRODUCTION
This manual is filled with time-saving and money-saving information regarding your
Cretors machine. There is nothing more important than the safety aids and warnings
that are throughout this document. The Safety Alert Symbol is used to identify topics of
primary safety concern wherever they appear. Furthermore, a separate section has
been included which deals exclusively with service and accident prevention.
If, after reviewing this manual, anything is unclear or technical problems are
encountered, contact the distributor from whom you purchased your machine for
assistance. If there are any additional questions, feel free to contact our Customer
Service Department at the address and/or phone number listed on the last page of this
manual. Always have the model and serial number of your machine available to assist
in obtaining the correct information.

MODEL 1100
10/20/2016
4
IV. PURPOSE OF MANUAL
This instruction manual is intended to familiarize owners with the operation and safety
procedures associated with your Cretors machine.
It is important that this manual be kept available to operating personnel.
A PERSON WHO HAS NOT READ AND UNDERSTOOD ALL
OPERATING AND SAFETY INSTRUCTIONS IS NOT QUALIFIED TO
OPERATE THE MACHINE.
V.
INSTALLATIONINSTRUCTIONS
A. Location
Choose a location for your case to maximize the ease of operation and maintenance
procedures. Check your local building and fire codes for location restrictions.
While unpacking the display case, carefully inspect it for missing parts or damage during
shipment.
B. Power Supply
Plug unit into a grounded outlet and turn on power switches (Items 18and 19).
This will turn the lights on, rotate the rack and start heating the cabinet. The
display case requires a 120-voltpower supply. Use a GROUNDED 120-VOLT
CIRCUIT WITH A 15-AMPBREAKERorFUSE. Donotuseanextensioncord.
THIS UNIT IS NOT FUSED. BE SURE TO CONNECT IT TO A
GROUNDED 120-VOLT CIRCUIT WITH A 15-AMP BREAKER OR
FUSE
VI. OPERATING INSTRUCTIONS
Operating the Display Case
1.
Turn off main power switch (Item 18)to stop rack rotation while
loading and unloading pretzels.
2.
Load the display case with up to five pretzels per rack arm (Item 14)fora total of 60
pretzels.
DO NOT OVER FILL.
3.
Turn on both switches to display pretzels and maintain lighting inside the case.
PRETZELS MUSTBECOOKED ASRECOMMENDED BYTHE
MANUFACTURER PRIORTODISPLAY.

MODEL 1100
10/20/2016
5
VII.
SANITATION INSTRUCTIONS
A clean, attractive display case is safer. Be sure to use cleaning materials that are non-
corrosive, non-abrasive, and food safe. Clean and sanitize with materials appropriate for
stainless steel and aluminum.
NEVER IMMERSE THE UNIT IN WATER. THIS APPLIANCE
SHOULD NOT BE CLEANED WITH A WATER JET.
BE CERTAIN THE MACHINE IS TURNED OFF AND POWER IS
UNPLUGGED BEFORE SANITIZING THIS MACHINE. FAILURE TO
DO SO COULD RESULT IN INJURY.
Do not clean appliances until they have been given sufficient time to cool. Failure to do
so may result in serious burns.
Unplug the unit and allow the unit time to cool. Remove all excess pretzels remaining on
the rack arms (Item 14).
To remove rack assembly, loosen the thumb screw located near the top that holds the
rack onto the gear motor shaft (Item 12).
NOTE: Be sure the thumb screw lines up with the hole on the shaft
during reattachment this ensure that the rack will not fall off if the thumb
screw loosens during use.
Reminder: Always completely reassemble the display case before operating
.

MODEL 1100
10/20/2016
6
VIII. MAINTENANCE INSTRUCTIONS
ONLY QUALIFIED PERSONNEL SHOULD PERFORM
DIAGNOSTIC CHECKS, AND, IF NECESSARY, CORRESPONDING
ADJUSTMENTS AND REPAIRS. MAINTENANCE OF THIS DEVICE
MAY PRESENT AN ELECTRICAL SHOCK HAZARD AND CAN
CAUSE SERIOUS INJURY OR DEATH.
PERFORM WORK ONLY ON DE-ENERGIZED CIRCUITS. FAILURE
TO DO SO MAY LEAD TO ELECTRICAL SHOCK, RESULTING IN
PERSONAL INJURY OR DEATH.
To access all electrical components, unplug power cord (Item 20) from outlet then lay
unit on its side to remove the four screws from the base cover (Item 1) exposing heating
element, switches and wiring. Use the wiring instructions on to aid in troubleshooting.
THIS UNIT IS NOT FUSED. Be sure to connect it to a grounded 120-volt
CIRCUIT WITH A 15-AMP BREAKER OR FUSE.
Periodically check all electrical switches and cords for signs of wear. Check all
screws and rivets for tightness.
IX. TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
ACTION
Will not heat.
Loose connection to the
heater.
Remove bottom cover and check for
loose connection.
If no loose connections, check for
continuity in element. If no continuity,
replace element.
Light will not work.
Bulb burned out.
Plug in machine and/ or turn on switch.
Turn off machine and/ or turn off
switch.
Replace bulb with recommended
replacement bulb.

MODEL 1100
10/20/2016
7
X. EXPLODED PARTS DIAGRAM
12
2

MODEL 1100
10/20/2016
8
XI. REPLACEMENT PARTS LIST
ITEM
PART NO.
DIAGRAM
DESCRIPTION
QUANTITY
1
1800
BASE COVER
1
2
1900
MOTOR DECK
1
3
1802
EXTRUSION • REAR
3
4
1901
EXTRUSION • CATCH
1
5
1902
BASE
1
6
1903
TOP CAP
1
7
1904
PLEXIGLAS DOOR
1
8
4866
DOOR HINGE (SET)
1
9
1905
STRIKE PLATE
1
1O
1820
MAGNETIC CATCH
1
11
1906
MAGNET BRACKET
1
12
1907
PRETZEL RACK GEARMOTOR
1
13
1908
PRETZEL RACK SHAFT
1
14
1909
PRETZEL RACK ARM
12
15
4864
HEAT LAMP SOCKET
2
16
2053
ID)
40 WATT BULB)
2
17
1823
/D)
FLEXIBLE HEATER WIRE ASS'Y
1
18
7250
MAIN POWER SWITCH
1
19
4855
KETTLE/HEAT LAMP SWITCH
1
20
1597
/D)
POWER CORD 16/3 SJT
1
21
2350
/D)
Slll.AJN RELIEF 6P34
1
22
832TINN
(N/S)
#8-32 TINNERMAN TYPE J NUT
10
23
4867
RUBBER FEET
4
25
1811
GLASS
3
(D) Denotes that part Is shown on WIRING DIAGRAM on PAGE 9.
(N/S) Denotes that part Is not shown on Illustrations.

MODEL 1100
10/20/2016
9
0
0
0
0
0
--&----
ff
-,
---------
,
r--
I\
I/
n
11
11
ti
--
U
--------i' --------- --
l
II II
lt
I
!I
u
II
-----
u
U
XII. WIRING DIAGRAM
Referenced to
REPLACEMENT
PARTS LIST on PREVIOUS
PAGE.
THIS VIEW FROM
UNDERNEATH TOP
CAP
THISVIEW FROM
UNDERNEATH
BASE
WITH BASE
COVER (ITEM 1)
REMOVED.
.

MODEL 1100
10/20/2016
10
This manual is filled with time-saving and money-saving information regarding your
Cretors oil pump. There is nothing, however, more important than the safety aids and
warnings found throughout this document.
If you have any questions regarding the operation or cleaning of your Cretors machine,
contact your local distributor. Should you have any difficulties or are unable to reach
them, feel free to contact the Customer Service Department at C. Cretors and Company.
Additional copies of this manual can be obtained from C. Cretors and Company at the
address listed below. Please provide the model and serial number when requesting
additional copies of this manual. There will be a nominal charge for additional copies.
Cretors guarantees this machine to be free of defects in parts, materials and
workmanship for two years. Please take this time to fill out the factory registration card
and return it to the factory to activate your warranty. If you have any questions
concerning the Cretors’ warranty, please contact your local distributor or the Customer
Service Department at C. Cretors and Company.
C. CRETORS AND COMPANY
176 MITTEL DRIVE
WOOD DALE, IL 60191
PHONE (847) 616-6900, (800) 228-1885, FAX (847) 616-6970
Table of contents
Other Cretors Display Case manuals
Popular Display Case manuals by other brands

Eurocryor
Eurocryor SPRING operating manual

Moducase
Moducase Df Series manual

Delfield
Delfield F15MR48D Specification sheet

Hussmann
Hussmann Austral H1 installation manual

Woodson
Woodson W.HFS Series Specification, installation and operation manual

Hatco
Hatco FLAV-R-FRESH FDWD Series Installation and operating manual