Crime Guard CG-850i3 User manual

CG-850i3
REMOTES: Standard - 4 Button / Lock icon-Unlock icon-II Second channel option-III Third channel option / Omega part # 119-05B Optional
3 Button Transmitter Part # 119-05R / 433MHz ET7A.
REMOTE OPERATION / (One Or Two Button Transmitter Operation):
One Button: Lock - Press and hold to Arm/Lock system Holding for 3 seconds activates the panic feature.
Unlock - Disarms the system and unlocks the doors (Unless the system is in the triggered condition.) Holding for 3 seconds
activates the panic feature.
Lock and Unlock - Pressed together will activate the remote start.
II - Pressing and releasing twice arms or disarms without confirmation chirps. Pressing for 2 seconds will activate the 2nd
channel output.
III - Pressing for 3 seconds will activate the optional 3rd channel output.
Two Button: Large Button-Press and release to Arm/Lock and Disarm/Unlock. Press and hold to activate Panic.
Middle Button and Lower Button - Pressed together will activate the remote start.
Middle Button- Press and hold to activate 2nd channel output.
Lower Button- Press and hold to activate 3rd channel output.
ZONE VIOLATION CODE: After remotely disarming the LED will flash one of the following codes if the alarm was activated while it was in
an armed state.
Flash 1 Red / Pause - System was triggered by current sense.
Flash 2 Red / Pause - System was activated from the hood or trunk circuit wire.
Flash 3 Red / Pause - System was activated from the door circuit wire.
Flash 4 Red / Pause - System was activated from the auxiliary input.
Flash 5 Red / Pause - System was activated from the optional pre-warn input.
REMOTE STARTING DIAGNOSTICS: Whenever the system is placed into Easy Valet Mode, the status indicator light illuminates solid red.
Then flashes 1-6 green flashes before resuming solid red.
Red / 1 Green Flash / Red =Programmed run time expired.
Red / 2 Green Flashes / Red = Brake was pressed or hood opened.
Red / 3 Green Flashes / Red = Engine stalled or bad tack signal.
Red / 4 Green Flashes / Red = Received transmitter command to stop.
Red / 5 Green Flashes / Red = Gear selector removed from “park”.
Red / 6 Green Flashes / Red = Security system triggered or low voltage.
CODING REMOTES: 4-Button type/ Turn the ignition “ON”. Press and release valet switch 5 times. The siren will chirp. Press LOCK button
on each remote to be coded. (One at a time.) Turn the ignition “ON”. Press and release valet switch 5 times. The siren will chirp. Press The Big
Button On Each Remote To Be Coded. (One at a time.) NOTES
1) Unit has new “Smart Trigger” feature that makes Dome Light Supervision installation easier.
2) There are 2 ways to monitor the engine running: Tach-Sensing or Voltage Sensing.
1) Unit automatically takes sensor “Off-Line” during remote start.
2) Two sensor imputes.
3) Positive output for a siren.
4) Plug in port for RS-RP to add additional ignition outputs.
5) Unit is compatible with the FPM-1.
6) Unit has “STORM” (Safety Disable) feature. (Pressing UNLOCK while the alarm is in the triggered condition will not unlock the
doors. This is very useful when sensors are being disturbed by the weather.)
7) PIT-STOP feature allows the engine to run without the key. By pressing the valet switch twice, the parking lights flash and the
siren will chirp 5 times, then turn the key off, the engine will run without the key.
8) Remote starting Preactivation feature.
9) Easy valet mode.
10) Starting valet mode.
11) Both full valet mode SAFETY FEATURES
WHILE THE ENGINE IS RUNNING:
1. Pressing the brake pedal will stop the engine.
2. Removing the gear shifter from “Park” will stop the engine.
3. Opening the hood will stop the engine.
THIS UNIT WILL NOT ACTIVATE IF THE FOLLOWING SAFETY CIRCUITS ARE TRIGGERED:
1. Gear shifter not in “Park”. (Produces 1 long chirp.)
2. Open hood. (Produces 1 long chirp.)
Pressed brake pedal. (Produces 1 long chirp.)

Programmable Features
Turn ignition “on” then “off”. Press and release valet button 5 times. Unit will enter feature set-up. Press valet button equal to the feature
number you wish to change.
FEATURE# DEFAULT LOCK UNLOCK
Feature #1 Current Sensing OFF ON OFF
Feature #2 3 or 210 Second Current Sensing Delay 3 210 3
Feature #3 30 or 60 Second Alarm Duration 60 60 30
Feature #4 3 or 45 Second Arming Delay 3 45
Feature #5 Last Door Arming OFF ONOFF
Feature #6 Automatic Rearming OFF ON OFF
Feature #7 Disarm Upon Trunk Release ON ON OFF
Feature #8 Parking Lights Upon Disarm ON ON OFF
Feature #9 Doors Lock With Ignition “ON” ON ON OFF
Feature #10 Ignition OFF Unlock #1 ON ON OFF
Feature #11 Ignition OFF Unlock #2 ON ON OFF
Feature #12 Open Door Bypass To The Previous Three Features ON ON OFF
Feature #13 Doors Lock With Last Door Arming OFF ON OFF
Feature #14 Automatic Rearming Lock OFF ON OFF
Feature #15. Door Lock Unlock Pulse Duration .8 3 .8
Feature #16 Double Unlock Pulse OFF ON OFF
Feature #17 28 Second Lock Pulse OFF ON OFF
Feature #18 Ignition Vehicle Recovery OFF ON OFF
Feature #19 Door Activated Vehicle Recovery OFF ON OFF
Feature #20 Transmitter Activated Vehicle Recovery OFF ON OFF
Feature #21 Confirmation Chirp ON ON OFF
Feature #22 Steady Siren / Pulse horn STEADY PULSED STEADY
Feature #23 Loud Or Soft Confirmation Chirps SOFT LOUD SOFT
Feature #24 One Or Two Button Transmitter Operation TWO ONE TWO
Feature #25 10 Or 20 Minute Engine Run Time 10 20 10
Feature #26 Steady Or Flashing Lights STEADY FLASH STEADY
Feature #27 Gas Or Diesel Engine GAS DIESEL GAS
Feature #28 Extended Crank Time MIN.7 NOTE 1 MIN.7
Feature #29 Tachless Or Tach Operation TACH LESS TACH
Feature #30 Preactivation ON OFF ON
NOTE 1: Each time you press lock button the extended start will advance to the next highest base start time (Two Chirps 1.25 SEC.
Three Chirps, 1.75SEC, Four Chirps 2.5 SEC.). Total System Reset
Method # 1: Preset the FPM-1 to default settings, access feature set-up and reset.

Starter
Yellow: Ignition Input/Output
Battery+
Black: (-) Ground
Red: (+) 12 Volts
30 Amp
30 Amp
Red/White: (+) 12 Volts
Pink: (-) 3rd Channel
Output
✄
White: To Starter Red: To
Ignition Switch
Relay
Orange: Armed (-) Output
Switch
Ignition
White:
Accessory Output
Green:
Starter
Output
AU-SOCKET & relay for starter interrupt
10 Amp
(-) Door Pin Switch
Hood / Trunk Switch
Or Pin
Brown: (+) Siren Output
(+) Door Pin Switch
Siren Red wire
Siren Black wire
to Ground
Light
Switch
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Parking Lights
White: (+) Parking Light Output
Blue: (-) Instant
Violet: (+) Door 10 Amp
1.5 Amp
Green:
(-) Door
Green/Violet: Dome Light Output - connect to vehicle’s dome light wire
see reverse side
Black/Red:
To (-) or (+) as needed
Keyless Entry and Security
Crime Guard
850i3
To (+) 12 volt
To vehicle's circuit or optional device
To (+) or (-)
as needed
Optional relay for
3rd Channel Output
Antenna Cable: Route this cable as high in the vehicle as practicle, and leave the clear center conductor exposed, if possible, and away from metal parts of the vehicle.
Smart Trigger Port
see reverse side
Auxiliary Sensor Port #1
see reverse side
Auxiliary Sensor Port #2
see reverse side
LED/Valet Switch/Data Port
Combination Assembly
Data Port is
behind plug- see
optional FPM-1
instructions
Black/Yellow: Tach Input
see reverse side
P R N D L
Blue/White: Neutral Safety (-)
Red/Black: Brake (+)
Satellite
Relay Ports
see reverse side Doorlock
Output Port
see Installation Manual
Yellow/Red: Factory Disarm Output
see Installation Manual
To (+) 12 volt
Optional relay for
trunk release
To (+) 12 volt or (-) ground
To vehicle’s trunk release wire
Gray: (-) Trunk Release Output
Yellow White Green Red/White Red Black
Siren
IS-CG-850i3