CrimeStopper REVO-1 Series User manual

REVO-1, REVO-3, REVO-4
1-Way RemoteStartSystem
INSTRUCTIONS
CONGRATULATIONS on your choiceofaCrimestopper RevoStart1-WayRemoteStartSystem. Thissystemis
an RFAntenna Decoder thatplugsdirectlyintoaFortinor ADSDatamodule.Noadditionalremotestartmoduleis
needed.The featuresofthe system,dependson the vehicleand datamoduleused.ThissystemrequiresaFortin
orADSdatamodulewithaprogrammertoloadcorrectvehiclesoftware.Youwillneedthevehicleinstallguidefrom
Fortinor ADSiDatalinkwebsite.Manyvehicleshavea“PlugnPlay”Tharnessavailabletosimplifytheinstallation.
The remotesneed tobe programmed after installation ofdatamodulebefore operation.Ifanyquestionsarise,
contact your installation dealer or Crimestopper SecurityProductsInc.
CRIMESTOPPERSECURITYPRODUCTS, INC.
1770 S. TAPO STREET, SIMIVALLEY, CA. 93063
REV 09-2013
ThisdevicecomplieswithFCC Rulespart15.Operation is
subjecttothe following twoconditions: 1)Thisdevicemaynot
causeinterference,and (2)thisdevicemustacceptany
interferencethatmaybe received,including interferencethat
maycauseundesired operation.The manufacturerisnot
responsibleforanyradioorTVinterferencecaused by
unauthorized modification tothisequipment. Suchmodification
couldvoidthe user'sauthoritytooperatethe equipment.

2
USINGTHEREMOTETRANSMITTER
VEH
VEH
REVO-1 REVO-3 REVO-4
ForREVO-1
The transmitter supplied hasone Start button.
ForREVO-3
The transmitter supplied withthissystemhas4verticalbuttons–Lock, Unlock, VehicleSelect and Start.
ForREVO-4
The transmitter supplied withthissystemhas5verticalbuttons–Lock, Unlock, TrunkRelease, VehicleSelect
and Start. Thisremotecan controlup to4AUXfunctionsthru datadepending on the vehicleand datamodule.
Thisistypicallyused for operating left and right sliding doorsand GasCap release. Consult your installer.
VEH1=BlueLED
VEH2=Red LED
REVO-4
AuxChannels
AUX1=Trunk+Lock
AUX2=Trunk+Unlock
AUX3=Trunk+Start
AUX4=Lock +Start

3
BATTERYREPLACEMENT
To replace thebatteryon 1button remote:
Simplyremovethe screwon backofthe transmitter and slide the caseapartasshown.Removethe twoCR-1620
Lithiumbatteriesand replace. Put casebacktogether and tighten screw.

4
BATTERYREPLACEMENT
To Replace theBatteryon 3and 4button remote:
The RemoteControlusestwoCR-2025 Lithium3VoltBatteries.Simplyremovethe Phillipsscrewlocated behind
keyring (see diagrambelow). Useasmall screwdriver asshowninFigure 2toremovethe backcover.Slide old
batteriesout. Insertthe newbatteriesintoplasticcover and slide intoplacewiththe (+)end facing up.The plastic
cover keepsthe batteriesfromshorting out against the side of metalhousing.
VEH CR2025
Remove
Screw

5
2VEHICLEOPERATION
AsingleRemote Control cancontrol twodifferentvehicles.
Toset up the 2-Vehicleoperation you must first programyour remotestoVehicle#2. Followthe “Transmitter
Programming”steps(Pg. 6) at the second vehicleand learn YOUR remote, along withvehicle#2’sexisting
remotes.
VEH
VEH
Tochange fromvehicle1tovehicle2, press the VEH button on remotefor about 2seconds. The LEDon
remotewill change from BluetoRed. The VEHbutton can be used tokeep remotecontrolfromaccidentally
operating your vehicle.
VEH1=BlueLED
VEH2=Red LED

6
TRANSMITTERPROGRAMMING
Note: Programming ofData Moduletovehiclemust becompletedFIRST!
Thesystemlearnsup to4differenttransmittercodes.
There are 2methodsof programming remotesdepending on the Datamoduleused tooperateyour vehicle.
ADSiDatalinkProgramming:
1. Insert keyfob intoKeyport or placekeyinignition switch. Completestep 2within7seconds.
2. Cyclethe ignition on fivetimes(5xOff/On) rapidly.
3. Parking Light will flashonce(1x). Completestep 4within5seconds.
4. Press Lock(or start on 1button remote) button on remoteyou wishtoprogram.
5. Parking lightswill flashonce(1x)toconfirmthe remoteisprogrammed.
6. Toprogramadditionalremotes, repeat step 4&5. The systemcan accept up to4remotes.
7. The systemwill automaticallyexit remotelearning procedure after 5secondsof inactivityand the parking
lightswill flashtwice(2x)toconfirmprogramming exit.
Fortin EVO-ALL Programming:
1.Put the EVO-ALL inprogramming mode (see install guide), releaseprogramming button on BLUE/RED.
2.Press and holdthe programming button on EVO-ALL for 5seconds. The 2LED’swill shut downand turn
backONafter 5seconds.
3.Turn the Ignition ON.
4.Press the “Lockor Start”button on remoteyou wishtoprogram.
5.The BLUEand REDLED’swill flashoncetoconfirmremoteiscoded.
6.Toprogramadditionalremotespress the Lockor Start button of eachremote.
7.The BLUEand REDLED’swill flashoncetoconfirmeachremoteiscoded.
8.Turn Ignition OFF onceall remoteshavebeen programmed.

7

8
www.crimestopper.com
[e-mail]
Phone [phone]
FAX [phone]
©2013 CrimestopperSecurityProducts